Loading ...
Loading ...
Loading ...
LCD Operation
GETTING READY
15
1
Settings screen
Press to change the default machine settings. Press
or , after you changed necessary settings.
Q Sewing settings
1 Select whether to use the sewing speed controller to
determine the zigzag width. (page 66)
2 Make adjustments to character or decorative stitch
patterns. (page 73)
3 Set to [ON] when using twin needle. (page 71)
4 Adjust the height of the presser foot when the presser
foot is raised.
5 Adjust the presser foot pressure. The higher the number,
the greater the pressure will be. Set the pressure at [3]
for normal sewing.
6 Select either “1-01 Straight stitch (Left)” or “1-03 Straight
stitch (Middle)” as the utility stitch that is automatically
selected when the machine is turned on.
7 Adjust the height of the presser foot when sewing is
stopped when the pivot key is selected. (page 37)
8 Adjust the height of the presser foot when the machine is
set to free motion sewing mode. (page 64)
9 When set to [ON], the thickness of the fabric is
automatically detected by an internal sensor while
sewing. This enables the fabric to be fed smoothly.
(page 36)
0 When set to [ON], reinforcement stitches are sewn at the
beginning and/or end of sewing for a reinforcement
stitch pattern, even when the (Reverse stitch button)
is pressed.
A When set to [ON], pressing the “Start/Stop” button (or
depressing the foot controller) automatically lowers the
presser foot when it is raised, allowing sewing to begin.
B When set to [ON], pressing the “Start/Stop” button (or
releasing the pedal of the foot controller) to stop sewing,
it will then automatically raise the presser foot. The
presser foot is raised to the height specified for [Presser
Foot Height] on page 2 of the settings screen.
When the pivot setting is selected, the presser foot is
raised to the height specified for [Pivoting Height] on
page 3 of the settings screen.
C When set to [ON], pressing (Thread cutter button)
automatically lowers the presser foot when it is raised,
allowing the thread to be cut.
After the thread is cut, the presser foot is raised again.
Q Embroidery settings
1 Select the embroidery frame to be used.
2 Select the center mark and grid lines that are displayed.
3 When set to [ON], you can only select the embroidery
pattern corresponding to the embroidery frame size that
you selected in
1. (page 86)
4 Change the thread color display on the embroidery
screen; thread number, color name. (page 89)
5 When the thread number [#123] is selected, select from
thread brands. (page 89)
6 Select the maximum embroidery speed setting.
7 Adjust the upper thread tension for embroidering.
(page 91)
8 When set to [ON], pressing the "Start/Stop" button when
the presser foot is raised automatically lowers the
presser foot before starting embroidering. (page 91)
9 Select the height of the embroidery foot during
embroidering. (page 82)
0 Select the color of the background for the embroidery
display area.
A Select the color of the background for the thumbnail
area.
B Select the size of pattern thumbnails.
C Select the display units (mm/inch).
Memo
• The latest version of software is installed in your
machine. Check with your local authorized Brother
dealer or at “ http://s.brother/cpham/
” for available
updates.
• You can save the current settings screen image in
a USB flash drive by pressing when the USB
flash drive is inserted into the USB port. The files
are saved in a folder labeled “bPocket”.
1
2
3
4
5
6
7
8
9
0
A
B
C
3
2
1
4
5
6
7
8
0
9
A
B
C
Loading ...
Loading ...
Loading ...