Loading ...
Loading ...
Loading ...
20
If the coee machine is left unused with the lter installed, it
will last a maximum of three weeks.
3. To activate the lter, run tap water through the hole in the
lter as shown in g. 35 until water comes out of the open-
ings at the side for more than a minute.;
35 36
0,5 L
4. Extract the tank (A17) from the appliance and ll with
water;
5. Insert the lter in the water tank and immerse it complete-
ly for about ten seconds, sloping it and pressing it lightly to
enable the air bubbles to escape (g. 36).
6. Insert the lter in the lter housing (A18) and press as far
as it will go (g. 37);
7. Close the tank with the lid (A16) (g. 38), then replace the
tank in the machine;
37 38
When you install the lter, you must notify the appliance of its
presence.
8. Press
(B6) to enter the "Settings" menu;
9. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two lines. Press OK;
10. Press the selection arrows until "Install lter" is displayed,
then press OK;
11. Conrm?": press OK;
12. "Hot water, Conrm?": Position a container under the hot
water spout (C6) (min. capacity: 500 ml), then press OK;
13. The appliance begins hot water delivery and the message
"Please wait" is displayed;
14. After the ow of hot water stops, the appliance automati-
cally resets to "Ready for coee" status.
The lter is now active and you can use the coee machine.
17.2 Replacing the lter
Replace the lter (C4) when "Replace lter, ESC to cancel, OK to
replace" appears on the display (B1). To replace immediately,
press OK (B3) and follow the instructions from point 8. To re-
place later, press ESC (B5). The
symbol on the display reminds
you that the lter needs replacing.
To replace the lter, proceed as follows:
1. Extract the tank (A17) and exhausted lter;
2. Take the new lter out of its packet and proceed as illus-
trated in points 2, 3, 4, 5, 6 and 7 in the previous section;
3. Press
(B6) to enter the "Settings" menu;
4. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two lines. Press OK;
5. Press the selection arrows until "Replace lter" is dis-
played, then press OK;
6. Conrm?": press OK;
7. "Hot water, Conrm?": Position a container under the hot
water spout (C6) (min. capacity: 500 ml), then press OK;
8. The appliance begins hot water delivery and the message
"Please wait" is displayed;
9. After the ow of hot water stops, the appliance automati-
cally resets to "Ready for coee" status.
The new lter is now active and you can use the coee machine.
Please note!
After two months (see date indicator) or when the appliance has
not been used for 3 weeks, you should replace the lter even if
the message has not yet been displayed.
17.3 Removing the lter
If you want to use the appliance without the lter (C4), you
must remove it and notify the appliance of its removal. Proceed
as follows:
1. Extract the tank (A17) and exhausted lter;
2. Press
(B6) to enter the "Settings" menu;
3. Press the selection arrows (B2 and B4) until "Maintenance"
is displayed between the two lines. Press OK;
4. Press the selection arrows until "Remove lter" is dis-
played, then press OK;
5. "Conrm?": press OK to conrm removal. The appliance
goes back to the "Maintenance" menu;
Press
/ESC (B5) to exit the menu.
Loading ...
Loading ...
Loading ...