Loading ...
Loading ...
Loading ...
19
11. "Rinsing underway": hot water is delivered rst from the
coee spouts, then from the hot water spout;
12. When the water in the tank has run out, empty the con-
tainer used to collect the rinsing water;
13. "Rinse tank and ll with water": extract the water tank and
ll with fresh water up to the MAX level. Press OK;
14. "Insert lter": put the water softener lter (if removed)
back in its housing in the water tank, and replace the tank
in the appliance. Press OK;
15. "Place 1.8L container empty under spouts":
place the con-
tainer used to collect the descaler solution empty under
the hot water spout. Press OK;
16. "Rinsing Conrm?": press OK.
17. "Rinsing underway".
Hot water comes out of the hot water
spout;
18. "Empty drip tray": At the end of the second rinse, remove,
empty and replace the drip tray (A15) and grounds con-
tainer (A11). Press OK;
19. "Descale complete": press OK;
20. "Fill tank": empty the container used to collect the rinse
water, remove the water tank and ll with fresh water up
to the MAX level, then put back in the appliance.
Descaling is complete.
Please note!
• If the descaling cycle is not completed correctly (e.g. no
electricity) we recommend repeating the cycle;
• After descaling, it is normal for the grounds container
(A11) to contain water;
• If the water tank has not been lled to the MAX level, at
the end of descaling, the appliance requests a third rinse to
guarantee that the descaler solution has been completely
eliminated from the machine's internal circuits.
• The appliance may request descaling cycles at very short
intervals. This is normal and due to the appliance’s ad-
vanced control system.
16. SETTING WATER HARDNESS
The descale message is displayed after a period of time estab-
lished according to water hardness.
The machine is set by default for a hardness level of 4. The ma-
chine can also be programmed according to the hardness of the
mains water in the various regions so that the machine needs to
be descaled less often.
16.1 Measuring water hardness
1. Remove the "TOTAL HARDNESS TEST" indicator paper (C1)
from its pack (attached to the English instructions);
2. Immerse the paper completely in a glass of water for one
second;
3. Remove the paper from the water and shake lightly. After
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. Each square corresponds to
one level;
16.2 Setting water hardness
1. Press
(B6) to enter the "Settings" menu;
2. Press the selection arrows (B2 and B4) until "General" is
displayed between the two lines. Press OK;
3. Press the selection arrows until "Water hardness" is dis-
played, then press OK;
4. The current selection appears on the display and the new
selection ashes. Press the selection arrows until the re-
quired new selection is displayed. Press OK.
The new level is saved and the appliance goes back to the "Gen-
eral" menu.
Press /ESC (B5) twice to go back to the main screen.
17. WATER SOFTENER FILTER
Certain models are tted with a water softener lter (C4). If this
is not the case with your model, you are recommended to pur-
chase one from De’Longhi Customer Services.
To use the lter correctly, follow the instructions below.
17.1 Installing the lter
34
1. Remove the lter (C4)
from the packaging. The
date indicator disk varies
according to the lter
provided.
2. Turn the date indicator
disk (g. 34) until the
next 2 months of use are
displayed.
Please note
The lter lasts about two
months if the appliance is
used normally.
soft water (level 1)
hard water (level 3)
very hard water (level 4)
slightly hard water (level 2)
Loading ...
Loading ...
Loading ...