Black+Decker BDH1715SMAPB Liftreach-Head SteamMop

Instruction Manual - Page 8

For BDH1715SMAPB.

PDF File Manual, 24 pages, Read Online | Download pdf file

BDH1715SMAPB photo
Loading ...
Loading ...
Loading ...
ENGLISH
6
To Re-Fit the Lift+Reach Head
1. Return the handle tube
4
to the upright position and
turn the steam mopOFF.
2. Wait until it cools down. (approximately five minutes)
3. Place the front of your shoe onto the Lift+Reach™ head
cleaning pad removal tab and press downfirmly.
4. Lift the Lift+Reach™ head
6
up off the cleaningpad.
5. Place the tip of the Lift+Reach™ head into the steam
head
5
and push downward. Ensure it is locked into
place by gently pulling upwards on thehandle.
NOTICE:
Do not store with a wet pad as this can
damage your floor. Always place the steam mop with
the handle
4
in the upright position when stationary
and make sure the steam mop is turned OFF when
not inuse.
Hints for Optimum Use (Fig. A)
WARNING: It is important to monitor the water level
in the water tank. To refill the water tank and continue
to sanitize/ clean, see Filling the Water Tanksection.
NOTICE: Never leave the steam mop in one spot on
any surface for any period of time. Do not store with a
wet pad as this can damage your floor. Always place
the steam mop with the handle tube
4
in the upright
position when stationary and make sure the steam
mop is turned off when not inuse.
Always vacuum or sweep the floor before
using the steammop.
The easiest way to use the steam mop is to tilt the
handle to a 45˚ angle and clean slowly, covering a small
area at atime.
Do not use chemical cleaners with your steam
mop. To remove stubborn stains from vinyl or linoleum
floors, you can pre-treat them with a mild detergent and
some water before using the steammop.
Steam Cleaning
1. Place a cleaning pad
7
on the floor with the ‘loop’ side
facingup.
2. Lightly press the steam mop down onto the cleaning
pad
7
.
3. Plug the steam mop into a walloutlet.
4. Press the ON/OFF switch
1
. It takes approximately
15-30 seconds for the steam mop to heatup.
5. Press the steam operate button
2
. After a few seconds,
steam will start to come out of the steamhead.
NOTE: If the system has been run dry it may take up to 45
seconds to prime the system on firstuse.
6. It takes a few seconds for steam to enter the cleaning
pad. The steam mop will now glide easily over the
surface to be sanitized/cleaned.
7. Push and pull the steam mop slowly across the surface
to thoroughly steam clean eachsection.
8. When you have finished using the steam mop, return
the handle
4
to the upright position, making sure that
it is supported and turn itOFF.
9. Wait until the steam mop cools down (approximately
fiveminutes).
NOTICE: It is important to monitor the water level
in the water tank
3
. To refill the water tank and
continue to sanitize/clean stand the mop upright
making sure that the handle is supported and turn the
steam mop ‘OFF’. Unplug the unit from the electrical
wall outlet, refill the water tank
3
.
NOTICE: Never leave the steam mop in one spot
on any surface for any period of time. Always place
the steam mop with the handle 
4
supported in the
upright position when stationary and make sure the
steam mop is turned off when not inuse.
After Use (Fig. A, G)
1. Press the steam operation button
2
to OFF and then
press the ON/OFF switch
1
toOFF.
2. Unplug the steam mop from the electrical wall outlet.
3. Wait until the steam mop cools down
(approximately 15 mins).
4. Empty the water tank.
5. Remove the cleaning pad
7
and wash it for the next use.
6. Clip the power cord around the cord hooks
9
and
10
.
7. There is a hanging bracket
14
built into the back of
the hand grip
11
, which allows your steam mop to be
hung from a suitable screw on the wall. Always ensure
that your wall screw is capable of supporting the weight
of the steam mopsafely.
MAINTENANCE AND CLEANING
Your BLACK+DECKER corded appliance has been designed
to operate over a long period of time with a minimum of
maintenance. Continuous satisfactory operation depends
upon proper appliance care and regularcleaning.
WARNING: Before performing any maintenance or
cleaning on corded appliances switch off and unplug
theappliance.
Clean your appliance using a soft damp cloth. Never
let any liquid get inside the appliance; never immerse
any part of the appliance into a liquid. IMPORTANT:To
assure product SAFETY and RELIABILITY, repairs,
maintenance and adjustment should be performed
by authorized service centers or other qualified service
organizations, always using identical replacementparts.
For stubborn marks you can use a mild solution of soap
and water to dampen yourcloth.
Care of the Cleaning Pads
NOTICE: Follow the cleaning instructions printed on
the label of your cleaningpad.
Wash care instructions - Machine wash warm 140°F (60°C)
- No bleach - No fabric softener - Air dry only - Allow to dry
fully before re-use.
Loading ...
Loading ...
Loading ...