Loading ...
Loading ...
Loading ...
ENGLISH
5
Attaching the Water Tank (Fig. C)
1. Install the water tank
3
to the steam mop body
ensuring the water tank is securely inplace.
Attaching the Cleaning Pad (Fig. A, D)
Replacement cleaning pads, SMP20, are available from
your BLACK+DECKER dealer. Replacement cleaning pads
for Lift+Reach™ head are SMP30
1. Place cleaning pad
7
on the floor with the “loop” side
facingup.
2. Lightly press steam mop or Lift+Reach™ head down
onto the cleaning pad. You are now ready to steam
clean and sanitize your floor.
NOTICE:
Do not store with a wet pad as this can
damage
your floor. Always place the steam mop with
the handle
4
in the
upright position when stationary
and make sure the steam mop is turned off when not
inuse.
Removing a Cleaning Pad
WARNING: Always wear suitable shoes when
changing the cleaning pad on your steam mop. Do
not wear slippers or open toedfootwear.
1. Return the handle
4
to the upright position and turn
the steam mopOFF’
2. Wait until the steam mop cools down (approximately
5minutes).
3. Lift the steam mop away from the cleaning pad freeing
it from the velcrofastening.
WARNING: Always place your steam mop with the
handle
4
supported in the upright position when
stationary and make sure the steam mop is turned off
when not inuse.
Filling Water Tank (Fig. E)
WARNING: Do not over fill the tank.
NOTE: Do not use chemical cleaners with your steam mop
watertank.
NOTE: Fill the water tank with clean tapwater.
NOTE: In areas of hard water, the use of distilled water
isrecommended.
NOTE: Ensure the filler cap is firmly secured.
NOTE: Always empty the water tank afteruse.
1. Make sure the steam mop is turned OFF andunplugged.
2. Remove water tank from the steam mop body.
3. Open the water tank filler cap
13
.
4. Fill the water tank
3
withwater.
5. Replace the water tank filler cap
13
.
NOTE: Ensure the water tank filler cap
13
is
firmlysecured.
WARNING: Your water tank has a 380 ml capacity.
Do not over fill thetank.
OPERATION
CAUTION: Never use the steam mop without first
attaching a cleaningpad.
IMPORTANT: This unit will kill 99.9% of germs when used in
accordance with the instructions in this manual and with the
micro-fiber pad fitted and a continuous run time of 90seconds.
NOTICE:
Do not use on any unsealed hard floor
surfaces. Additionally, on surfaces that have been
treated with wax or some no wax floors, the sheen
may be removed by the heat and steam action. It
is always recommended to test an isolated area of
the surface to be cleaned before proceeding. We
also recommend that you check the use and care
instructions from the floormanufacturer.
NOTICE:
Never leave the steam mop in one spot on
any surface for any period of time. Do not store with a
wet pad as this can damage your floor. Always place
the steam mop with the handle tube
4
in the upright
position when stationary and make sure the steam
mop is turned OFF and unplugged when not inuse.
NOTICE:
Always empty the water tank afteruse.
Switching On and Off (Fig. A)
NOTE: It takes approximately 30 seconds for the steam mop
to heatup.
1. To switch the appliance ON, press the On/Off button
1
.
2. Press the steam operation button
2
. This will operate
the pump and the unit will begin to producesteam.
3. To stop steam generation, press steam operation
button
2
a second time. This will maintain power to
the boiler for quicker startup.
4. To switch the appliance OFF, press the On/Off button
1
.
NOTICE:
Never leave the steam mop in one spot on
any surface for any period of time. Always place the
steam mop with the handle tube
4
supported in the
upright position when stationary and make sure the
steam mop is turned off when not inuse.
NOTICE:
Always empty the steam mop afteruse.
NOTE: When first filled or after running dry, it can take up to
45 seconds for steam to beproduced.
The Lift+Reach
TM
Head (Fig. F)
This Steam Mop incorporates a built in Lift+Reach™ head
which enables you to access tight corners and narrowgaps.
CAUTION: Always wear suitable shoes when
accessing the Lift+Reach head on your steam mop.
Do not wear slippers or open-toedfootwear.
To Access the Lift+Reach Head
1. Return the handle to the upright position and turn the
steam mopOFF.
2. Wait until it cools down (approximately five minutes).
Place the front of your shoe onto the steam head
removal tab
12
and press downgently.
3. Lift the Lift+Reach™ head up off the steam head
5
.
4. Place the Lift+Reach™ head cleaning pad
8
on the floor
with the hook and loop side facingup.
5. Press the Lift+Reach™ head down onto the cleaning
pad
8
. You are now ready to steam clean and sanitize
yourfloor.
1. Press the Lift+Reach™ head down onto the cleaning
pad
8
. You are now ready to steam clean and
sanitize yourfloor.
Loading ...
Loading ...
Loading ...