Loading ...
Loading ...
Loading ...
ENGLISH
13
Tool Use and Care
• Do not use the tool if the switch does not turn it on or
off. Any tool that cannot be controlled with the switch is
dangerous and must berepaired.
• Store idle laser products out of the reach of children and
do not allow persons unfamiliar with the laser product
or these instructions to operate the laser product. Laser
products are dangerous in the hands of untrainedusers.
• Use only accessories that are recommended by the
manufacturer for your model. Accessories that may be
suitable for one tool, may become hazardous when used with
anothertool.
The RBRC® Seal
Please take your spent battery packs to an
authorized DeWALT service center or to your
local retailer for recycling. In some areas,
it is illegal to place spent battery packs in
the trash. You may also contact your local recycling center
for information on where to drop off the spent battery pack.
Do not place in curbside recycling. For more information visit
www.call2recycle.org. or call the toll free number in the
RBRC®Seal.
RBRC® is a registered trademark of Call 2Recycle,Inc.
Installing and Removing the Battery Pack
(Fig.E)
NOTE: For best results, make sure your battery pack is
fullycharged.
To install the battery pack
15
, align the battery pack with
the rails inside the laser’s battery port and slide it in until the
battery pack is firmly seated in the laser and ensure that it does
notdisengage.
To remove the battery pack from the laser, press the release
button and firmly pull the battery pack out of the battery port.
Insert it into the charger as described in the charger section of
thismanual.
Operation
Operating Tips
• To extend battery life per charge, turn the laser off when it is
not inuse.
• To ensure the accuracy of your work, check the laser
calibration often. Refer to Calibrating theLaser.
• Before attempting to use the laser, make sure the tool is
positioned on a relatively smooth, securesurface.
• Always mark the center of the laser line or dot. If you mark
different parts of the beam at different times you will
introduce error into yourmeasurements.
• To increase working distance and accuracy, set up the laser in
the middle of your workingarea.
• When attaching to a tripod or wall, mount the lasersecurely.
• When working indoors, a slow rotary head speed will produce
a visibly brighter line, a faster rotary head speed will produce
a visibly solidline.
• To increase beam visibility, wear Laser Enhancement Glass es
and/or use a Laser Target Card to help find the beam.
WARNING: These are not ANSI Z87.1 eyeprotection.
• Extreme temperature changes can cause movement or
shifting of building structures, metal tripods, equipment,
etc., which can affect accuracy. Check your accuracy often
whileworking.
• When working with the DeWALT Digital Laser Detector, set
the laser’s rotation speed to the fastestsetting.
• If the laser is dropped or has suffered a sharp blow, have the
calibration system checked by a qualified service center before
using thelaser.
Control Panel (Fig.A, B)
The laser is primarily controlled by the power button
1
, the
mode button
2
, the speed/rotation button
3
and the scan
mode button
4
. These features are then modified when
used with either the Axis selection button
5
(DW079LR/LG in
Slope mode only), or the two direction/elevation adjustment
buttons
6
and
7
.
The direction/elevation adjustment buttons control the
rotational direction of the laser head as well as adjust the
elevation of the beam when the unit is in slopemode. These
buttons can also be used to incrementally rotate the beam
when the unit is in Scanmode.
The buttons on the DW074LR control panel, DW079LR/
DW079LG control panel, and the DW079LR/DW079LG Remote
keypad all work the same, unless otherwiseindicated.
Power Button
The Power button is used to turn the laser unit on andoff.
• To power ON the DW074LR or DW079LR/LG laser unit,
press the Power buttononce.
• To completely power OFF the DW074LR or DW079LR/LG
laser unit, press the power button for 3sec.
Speed/Rotation Button
The speed/rotation button
3
is used to adjust the rotation
speed of the laser beam through its 4preset speeds (150, 300,
600, and 1200RPM).
Scan Mode Button
15˚/45˚/90˚
The scan mode button
4
is used to make the laser head sweep
back and forth, creating a short, bright laser line. This short line
is much brighter and more visible than when the unit is in full
rotationmode.
Using Scan Mode
• To enter Scan Mode, push and release the scan mode
button
4
. To cycle through the scan angles, continue to
press the button until you reach the desiredangle.
Loading ...
Loading ...
Loading ...