Loading ...
Loading ...
Loading ...
TEC_TM_009 | REV. G | EN 07/19/2022 Page 33 of 76TR-30/36 INSTALL MANUAL
PAGE TITLEINSTALLATION
PROCEDURE
1. Measure and mark the depth of the bracket's
placement in the installation location.
• For a flush installation: 24-31⁄32" (634.20625 mm)
• For a proud installation: 22-31⁄32" (583.40625 mm)
2. Place and center the bracket at the measured
depth.
3. With the bracket as a guide, drill pilot holes into the
wall and/or floor.
NOTE: FOR INCREASED STABILITY, SECURE
THE BRACKET TO AS MANY JOISTS AND/OR
STUDS AS POSSIBLE.
4. With the provided hardware, secure the anti-tip
bracket.
5. Adjust the rear leveling rollers 1⁄4 turn clockwise.
6. Slide the unit into place and hook the anti-tip
bracket into the castor assembly slots.
ANTI-TIP BRACKET INSTALLATION
KIT CONTENTS
• One (1) anti-tip bracket
• Four (4) 3⁄16" masonry screws
• Eight (8) #12 –2" wood screws
• Twelve (12) 1⁄4" washers
REQUIRED TOOLS
• Tape measure
• 7⁄16" socket
• Marking utensil
• Phillips bit driver
• 1 ⁄8" drill bit
• Drill or ratchet
WARNING! TIP OVER HAZARD. To avoid a
hazard from appliance instability, install
the anti-tip bracket in accordance with
the instructions below.
BEFORE YOU BEGIN
Consult a flooring expert to confirm that the flooring
where the unit will be installed is rated for at least 150
pounds per square foot.
22 31/32"
583mm
PROUD INSTALL
24 31/32"
634mm
FLUSH INSTALL
9 9/32"
236mm
9 9/32"
236mm
℄
TR-30REF-R-SG-A
R
℄
℄ = Center Line
–-– = Bracket Location
TOP VIEW
30 INCH / 36 INCH UNIT
ANTI-TIP BRACKET KIT:
• One (1) anti-tip bracket (Figure 1.1)
• Four (4) masonry 3/16” screws
• Eight (8) wood #12 – 2” screws
• Twelve (12) 1/4” washers
FOR ALL FULL SIZE RESIDENTIAL MODELS, THE ANTI-
TIP BRACKET ENGAGES WITH THE REAR LEVELING
LEGS TO SECURE THE UNIT. FOLLOW THESE STEPS
TO SECURE THE BRACKET BEFORE MOVING THE
UNIT INTO FINAL OPERATING POSITION.
1. Determine final location of the unit. For a FLUSH
install, measure back 24-31/32” (Dimension A)
from the surrounding cabinetry. For a PROUD
install, measure back 22-31/32” (Dimension B)
from the surrounding cabinetry. For either type of
install, place the anti-tip bracket centered in the
rough opening.
2. Using the bracket as a guide, drill pilot holes into the
wall/floor. It is recommended to secure the bracket
to as many floor joists and wall studs as possible.
3. Using the provided screws and washers, secure the
bracket to the wall/floor. Adjust the rear rollers to
just above their lowest position and move the unit to
its final position. Raise the rear rollers a minimum
of 1/8” to engage the bracket.
FIGURE 1.1 - ANTI-TIP BRACKET
987036
5.19.17 A L
TRUE RESIDENTIAL REFRIGERATION
UPRIGHT ANTI-TIP BRACKET INSTALLATION
30 INCH UNIT
22 31/32"
583mm
PROUD INSTALL
24 31/32"
634mm
FLUSH INSTALL
9 9/32"
236mm
9 9/32"
236mm
C
L
C
L
TR-30REF-R-SG-A
R
NOTE: DIMENSIONS MAY VARY BY ±
1
/
8
”
WARNING: To avoid a hazard due to instability of
the appliance, it must be fixed in accordance with
the instructions.
AVERTISSEMENT: Pour éviter tout risque dú a
l´instabilité del l´appareil, vous devez le fixer
conformément aux instructions.
Dimensions may vary by ± 1/8" (3.2 mm)
Loading ...
Loading ...
Loading ...