Loading ...
Loading ...
Loading ...
_i • _ _
i WARNING_ For yourow'n safety, turn switch "OFF", and remove plug from power source outlet before trou-
bleshooting your spindle: sander_
1
i
CAUSE .... REMEDY
Excessive noise:' _ :_: 1! Motor for gearbox. 1.ConsultSears Service, any attempt to repairthis
NOTE: The sandel_wiii motoror gearboxmay create a hazard unless repair
makesome noise when: _: ....... isdone by a qualifiedSears service technician.
itis operating normaily i _ :
Motor fails to develop::" 1. Circuit overloaded with lights, 1. Do not Use sander on heaviiyloaded circuits
full power, starts slowly;i
or fails to come up to full
speed,
NOTE: Low voltage
appliances and other motor.
2: General overloading of power
company facilities.
3. Motor relay not operating.
2, Request a voltage check by qualified electrician
,
Have relay replaced.Consult Sears Service, Any
attempt to repair this relay may create a hazard
unless repair isdone by a qualified Sears service
technician,
Motor overheats
Motor stalls (resulting in
blown fuses or circuit
breakers)
Frequent opening of
fuse or circuits breaker
1. Motor Overloaded. I. Reduce' Pressure on workpiece,
i. Motor relay not operating. I, Have relay replaced.Consult Sears 'i3ervice, Any
2. Voltage too low. Circuit over-
loaded or ger_eral overloading of
power company facilities.
3, Incorrect fuses or circuit breakers 3.
in power line.
1. Motor Overloaded. 1.......... 1.
2, incorrect fuses or circuit breaker 2.
in power line.
3. Relay not operating. 3.
• • • •••_ :••••-• • i•
Motor will not run 1. Damaged On-Off Swffch/Cord,
2: Burned out motor.
3. No power to motor,
.... 4. Low voltage.
attempt to repair this relay may create a hazard
unless repair is done by a qualified Sears service
technician.
2, Request voltage check by qualified electrician
Install correct fuse or circuit breaker,
Feed work slower in'to drum
Install correct fuse or circuit breakers,
Have relay replaced, Consult Sears Service, Any
............. ,,L
Sanding drum slips or 1. Applying too much pressure to 1.Ease up on workpiece.
slows down easily
attempt to repair this relay may create a hazard
unless repair is done by a qualified Sears service
technician,
_f.Replace damaged parts before using sander,' .......
2. Consult Sears Service, Any attempt to repair this
motor may create a hazard unless repair is done
by a qualified Sears service technician.
workpiece.
2. Lower drum washer not in place.
3, Incorrect or missing upper drum
washer.
4, Spindle nut too loose.
2, Install lower drum washer.
3, Install correct upper drum washer.
,
........ i ......................................
Wood burns while sand- 1, Sanding drum is glazed with sap, 1.
Tighten spindle nut,
Replace sanding drum,
ing
iSandpaper doesn't
iremove material
Spindle doesn't go
through full 3/4" travel
1. Sanding dru'rn"is compacted with
sawdust.
1. sawdust is compacted under
lower drum washer.
2. Damaged gearbox.
1. Replace sanding drum.
i'. Vacuum sawdust from area lower drum wash'er.
Ensure that lower drum washer is installed with
grooved side down,
2, Consult Sears Service, Any attempt to repair this
gearbox may create a hazard unless repair is
done by a qualified Sears service technician.
•20
; i:_ i_: _
Loading ...
Loading ...
Loading ...