Loading ...
FULL ONE YEAR WARRANW ON CRAFTSMAN BENCHTOP TOOLS
e Sander:fails dueto a defect in material or workmanship within one year
fi_omthe date of purchase, RETURN IT TOTHE NEAREST SEARS SERVICE CENTER IN THE UNITED
!STATES_Iand Sears will repair it, free of charge::
-_ifthis Oscillating Spindle Sander is used for commercial or rental purposes, this warranty will apply
for ninety days from the date of purchase.
This warranty applies only while this product is in the United States.
This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
= Sears, Roebuck and Co., I)/817 WA Hoffman Estates, IL 60179
Safety Instructions For Oscillating Spindle Sander .....
Safety is a combination of common sense, staying alert and knowing how your oscillating spindle sander works. Read
this manual to understand this sander,
Safety Signal Words
DANGER:means if the safety informationis not followed
someone will be seriously injured or killed.
Before Using The Sander
WARNING: To avoid mistakes that could cause !
/
serious, permanent injury, do not plug the sander
1
in until the following steps are completed.
• Assembly. (See pages 8-11)
° Learn the use and function of the ON-OFF switch,
(See page 13)
WARNING: means if the safety information is not fol-
lowed someone could be seriously injured or killed,
CAUTION: means if the safety information is not followed
someone may be injured.
.............. J i ....
- !
o Review and understanding of all safety instructions
and operating procedures in this manual.
-Review of the maintenance methods for this sander.
(See page 18)
Read the following WARNING label found on the front of
the sander:
[J JI [ L lI=lt_
1; Read manual before using sander. ,::: ::: :: i::: ,
: Wear_afety ....... :
= : i : : =
: ::3! Weara dust masl(_ :i:: : : :: ::
:4. Keep fingers away from abrasive s[beve:when machine ison.
i:
li ..... ;, ,,,,;.......... . , ,,,uu I II
i
.. ....................... ,,,,,,,,
When Installing Or Moving The Sander
Avoid dangerous environment. Use the sander in a
dry, indoor place protected from rain. Keep work area
well Fighted.
To avoid burns or other fire damage, never use the
5. Use the proper spacer ring insert for each sleeve to minimize pinch
points between sleeve and spacer ring insert.
6. Always support workpiece against the table.
7. Avoid fire, clean out all sawdust and disconnect
from any vacuum before sanding metals.
I i iii1,1 ,1_ i I ......... _,,,i
,,,,1.111 ,,,,,,,..,, nil
,, ,,,
,, ,,,,,,,,,,,,,,,,,
oNever use this or any power sander for wet sanding.
Doing so could cause electrocution, serious injury or
worse.
To avoid injury from unexpected sander movement:
sander near flammable liquids, vapors or gasses.
To avoid injury or death from electrical shock:
° Ground the sander. This sander has an approved 3-
conductor cord and a 3-prong grounding type plug.
Use only 3_wire, grounded outlets rated 120 volts, 15
amperes (amps), The green conductor in the cord is
........ the grounding wire, To avoid electrocution, Never con-
.... nect the green wire to .alive terminal.
::: i :"Make sure your fingers do not touch the plug's metal
:::: : :: plugging or unplugging the sander.
!
- Always unplug the sander before, moving it.
o Put the sander on a firm level surface where there is
plenty of room for handling and properly supporting the
workpiece.
Attach rubber feet. ::
o Support the sander so it does not rock:......
- Bolt the sander to its work surface. Use the fasteners
and method shown in "Assembly." (See page 9.)
o Never stand on too!. Serious injury could occur #the
tool tips. Do not store anything above or near the too]
where anyone might stand on the tool to reach it.
Loading ...
Loading ...
Loading ...