QP2724, QP2834
QP2724 QP2834
>75 % recycled paper
>75 % papier recyclé
Manufactured for: Philips Personal Health
a division of Philips North America LLC
P.O. Box 10313, Stamford, CT 06904, USA
This symbol on the product’s nameplate means it is
listed by Underwriters’ Laboratories, Inc.
Norelco is a registered trademark of Philips North America LLC.
PHILIPS and Philips shield are registered trademarks of
Koninklijke Philips N.V.
©2022 Philips North America LLC. All rights reserved.
3000.092.1303.2 (09/29/2022)
NOT INCLUDED
1-5 mm
QP2834
QP2834
3 mm
2
1
1
2
NOT INCLUDED
3
1
2
2
1
6
10
14
18
22
3
7
11
15
19
4
8
12
16
20
5
9
13
17
21
English
IMPORTANT SAFETY
INSTRUCTIONS
When using an electric product, basic precautions should
always be followed, including the following:
Read all instructions before using this product.
DANGER
To reduce the risk of electric shock:
- To charge the product, only use a USB power source on
a certied product with output rating 5V, ≥ 1A. For safe
charging in a moist environment (e.g. in a bathroom),
only use an IPX4 (splash-proof) power source. A
suitable power source (e.g. Philips HQ87) is available via
www.philips.com/support. If you need support nding
the correct USB power source, contact Philips support at
1-800-243-3050. Using a non-certied USB power source
may cause hazards or serious injuries.
- Keep the USB cable and the USB power source dry.
- Do not reach for a corded product that has fallen into
water. Unplug immediately from the power outlet.
- Do not place or store the product where it can fall or be
pulled into a tub or sink. Do not place or drop the product
into water or other liquid.
- This product does not work while it is connected to the
power outlet. Except when charging, always unplug this
product from the power outlet.
- Remove USB power source from power outlet and product
before cleaning the product with water.
WARNING
To reduce the risk of burns, re, electric shock, or injury to
persons:
- This product is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the product by a person responsible for their safety.
Children should be supervised to ensure that they do not
play with the product.
- Use this product only for its intended household use as
described in this manual. Misuse can lead do hazards or
serious injuries. Do not use attachments not recommended
by Philips North America LLC.
- Never operate this product if it has a damaged USB power
source, if it is not working properly, after it has been
dropped or damaged, or after the product or the USB
power source has been dropped into water. For assistance
call 1-800-243-3050.
- Keep the USB cable and the USB power source away from
heated surfaces.
- Never drop or insert any object into any opening.
- Do not use the USB power source in or near a power outlet
that contains an electric air freshener to prevent damage to
the USB power source.
- Do not use product outdoors or operate where aerosol
(spray) products are being used or where oxygen is being
administered.
- Always check cuttings units and other attachments and
accessories before you use the product. Never use the
product with a damaged cutting unit, attachment or
accessory, as injury may occur.
- Always attach the USB cable to the USB power source and
the product rst, then attach the USB power source to the
power outlet. To disconnect, set all controls to ‚o‘ position.
Then remove the USB power source from the power outlet.
- Plug USB power source directly into power outlet. Do not
use an extension cord.
- Unplug USB power source before plugging in or
unplugging the product.
- The batteries used in this product may present a re or
chemical burn hazard if mistreated. Do not disassemble,
heat above 100°C (212°F) or incinerate.
- Only use original Philips accessories or consumables.
- Charge, use and store the product at a temperature
between 41 °F / 5°C and 95 °F / 35°C.
- Keep product and batteries away from re and do not
expose them to direct sunlight or high temperatures.
- If the product becomes abnormally hot or smelly, changes
color or if charging takes longer than usual, stop using and
charging the product and contact Philips.
- Do not place products and their batteries in microwave
ovens or on induction cookers.
- Do not open, modify, pierce, damage or dismantle the
product or battery to prevent batteries from heating up
or releasing toxic or hazardous substances. Do not short-
circuit, overcharge or reverse charge batteries.
- If batteries are damaged or leaking, avoid contact with the
skin or eyes. If this occurs, immediately rinse well with water
and seek medical care.
- When you handle batteries, make sure that your hands, the
product and the batteries are dry.
- To avoid accidental short-circuiting of batteries after
removal, do not let battery terminals come into contact
with metal objects (e.g. coins, hairpins, rings). Do not wrap
batteries in aluminum foil. Tape battery terminals or put
batteries in a plastic bag before you discard them.
SAVE THESE
INSTRUCTIONS
Introduction
Congratulations on your purchase and welcome to Philips
Norelco!
To fully benet from the support that Philips Norelco oers,
register your product at www.philips.com/register.
General description (Fig. 1)
Your product comes with the following components included:
1 360 face blade
2 OneBlade handle
3 USB cable
Note: A suitable power source (e.g. Philips HQ87) is
available via www.philips.com/support.
4 5-in-1 guard
The following additional components are included with
QP2834 only:
1 Body blade
2 Click-on guard for body hair 1/8in. (3mm)
Getting started
- Use this product for its intended household use as
described in this manual.
- For hygienic reasons, the product should only be used by
one person.
- You can use this product either wet or dry, or even in the
shower. For that reason, this product does not work while
it is connected to the power outlet. Except when charging,
always unplug this product from the power outlet.
Charging OneBlade
Low Battery
When the battery is low, the motor will run more slowly.
Charging with the USB cable
Warning: Keep the USB cable and the USB power source
dry.
1 Insert the small plug of the USB cable into the socket in the
bottom of the product.
2 Insert the USB plug into the USB power source (not
included) (Fig. 2).
3 Insert the USB power source into the power outlet (Fig. 3).
4 To fully charge the battery, allow it to charge for 8 hours.
The charging indicator will remain illuminated when the
product is connected to the power outlet.
5 Unplug the adapter from the power source, then remove
the USB cable from the handle.
Note: for safety reasons, the product can only be used when
the USB cable is not attached.
6 A fully charged OneBlade has an operating time of
approximately 30 minutes.
Turning OneBlade on and o
To turn the product on or o, simply press the power button
once (Fig. 4).
Tip: If the product will not turn on, check that the battery is
fully charged and remove the charging cable from the handle
before pressing the power button.
Using OneBlade
Shaving and edging
To shave with OneBlade, remove any combs or guards. Your
OneBlade is waterproof, so you can shave in the shower or
with foam or gel.
1 To shave, make long, slow and steady strokes (Fig. 5),
applying gentle pressure with the blade at against your
skin (Fig. 6). Move the blade back and forth to make use of
both sides of the blade (Fig. 7).
2 To edge your beard (Fig. 8), mustache or sideburns, hold
the blade perpendicular to your skin (Fig. 9).
3 For best results, clean your OneBlade after each use.
Trimming facial hair
To trim the length of your facial hair, use the 5-in-1 guard. The
numbers on the guard relate to the hair length remaining after
trimming (in millimeters).
Tip: if you are unsure which length you prefer, start with the
longest setting and reduce the length further if necessary.
1 Hook the back of the guard over the back of the blade, then
gently press the front of the guard downwards until it clicks
into place (Fig. 10).
Note: if you experience diculties attaching the guard,
ensure that the two small hooks on the bottom (on the side
closest to the teeth) are properly aligned on the upper edge
of the blade.
2 Press down on the length dial on the comb using your
thumb, and roll it until your preferred length is selected
(Fig. 11).
3 Trim against the direction of hair growth (Fig. 12), with the
teeth of the guard at against your skin (Fig. 13).
4 To detach the guard, hold the handle rmly and gently lift
the guard o the blade (Fig. 14). For best results, clean your
OneBlade after each use.
Trimming body hair
Note: the following section applies to the QP2834 only.
The 1/8inch (3mm) body guard allows you to trim hair on
your body below the neckline (for example chest, armpits and
groin).
For hygiene reasons, we recommend using the separate body
blade provided when trimming body hair.
For delicate areas such as the groin, only trim when the guard
is attached.
1 Place the the guard onto the blade and gently press until it
clicks into place (Fig. 15).
2 Trim against the direction of hair growth, with the teeth of
the guard at against your skin. The guard is double sided,
so you can move your OneBlade back and forth to cut hairs
growing in dierent directions (Fig. 16).
3 To detach the guard, hold the handle rmly and gently
lift the guard o the blade. For best results, clean your
OneBlade after each use.
Maintenance
Cleaning OneBlade
Clean after each use
For a quick clean, simply blow on the blade and any
accessories to remove hairs and dirt (Fig. 17).
Thorough cleaning
1 Turn on your OneBlade and rinse it under the tap with cold
or lukewarm water (Fig. 18). If you shave with foam or gel,
be sure to remove all residue after each shave.
2 Guards can also be cleaned under the tap using warm
water.
3 Allow your OneBlade and accessories to air dry completely
before storage.
Note: Do not bang the handle on the sink or any hard surface,
a this may damage the product (Fig. 19). Do not use a towel or
cloth to dry the blade.
Storage
Store your OneBlade in a safe, dry location where it will not be
crushed, banged, or subject to damage. Do not wrap the cable
around the product when storing, and do not place or store
the product where it can fall or be pulled into a tub or sink,
water or other liquid while plugged in.
Blade Replacement
When to replace the blade
We recommend replacing the blade of your OneBlade at least
once every four months, or whenever the blade shows signs of
wear.
Wear indicator
A replacement symbol will gradually appear on the blade as
you use it. When the replacement symbol is fully visible, it‘s
time to replace your blade.
Note that accessories such as guards can prevent the
replacement symbol from becoming visible.
Tip: the replacement symbol resembles the arrow icon on the
handle of your OneBlade. For older blades, a green rectangle
may appear in place of the replacement symbol.
If blade is damaged
If you notice any damage on your blade, please replace it
immediately.
How to replace the blade
Before you begin, make sure your OneBlade is turned o and
any guards are removed.
1 Press the release slide upwards and lift o the old blade,
holding it by both short sides (Fig. 20).
Note: hold the blade before pressing the release slide,
because the blade may y o and become damaged.
2 The old blade can be discarded with your normal household
waste.
3 Remove your replacement blade from the packaging. To
avoid damaging the blade, don‘t use sharp objects or crush
the packaging.
4 Hold the new blade by both short sides and insert the
protrusions on the bottom of the blade into the slots on the
OneBlade handle (Fig. 21).
5 Gently press the blade downwards onto the handle until it
clicks into place.
6 Your OneBlade is now ready to use.
The following Philips Norelco replacement blade packs are
available for your OneBlade:
- Face blades: QP420/80 and QP430/80.
- Body blades: QP210/80, QP220/80 and QP230/80.
Assistance
For assistance, visit our website: www.philips.com/support
or call toll free 1-800-243-3050.
Online information is available 24 hours a day, 7 days a week.
Disposal
- This product contains a rechargeable battery which must be
disposed of properly.
- Contact your local town or city ocials for battery disposal
information. You can also call 1-800-822-8837 or visit
www.call2recycle.org for battery drop-o locations
(Fig.22).
- For assistance, visit our website www.philips.com/support
or call 1-800-243-3050 toll free.
- Your product is designed and manufactured with
high quality materials and components, which can be
recycled and reused. For recycling information, please
contact your local waste management facilities or visit
www.recycle.philips.com.
Full Two-Year Warranty
Philips North America LLC warrants this new product (except
blade) against defects in materials or workmanship for a
period of two years from the date of purchase, and agrees to
repair or replace any defective product without charge.
IMPORTANT: This warranty does not cover damage resulting
from accident, misuse or abuse, lack of reasonable care, the
axing of any attachment not provided with the product or
loss of parts or subjecting the product to any but the specied
voltage or batteries.*
NO RESPONSIBILITY IS ASSUMED FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES.
In order to obtain warranty service, simply go to www.philips.
com/support for assistance. It is suggested that for your
protection you return shipments of product by insured mail,
insurance prepaid. Damage occurring during shipment is not
covered by this warranty.
NOTE: No other warranty, written or oral, is authorized by
Philips North America LLC.
This warranty gives you specic legal rights, and you may
also have other rights which vary from state to state. Some
states do not allow the exclusion or limitation of incidental or
consequential damages, so the above exclusion and limitations
may not apply to you.
*Read enclosed instructions carefully.
45-DAY MONEY-BACK GUARANTEE
If you are not fully satised with your product send the
product back and we’ll refund you the full purchase price.
The product must be shipped prepaid by insured mail,
insurance prepaid, have the original sales receipt,
indicating purchase price and date of purchase, and
the money-back guarantee return authorization form
enclosed.
We cannot be responsible for lost mail.
The product must be postmarked no later than 45 days after
the date of purchase. Philips reserves the right to verify the
purchase price of the product and limit refunds not to exceed
suggested retail price.
To obtain the money-back guarantee service, please go to
www.PhilipsMoneyBack.com and follow the simple 3-step
process.
Delivery of refund check will occur 6–8 weeks after receipt
of returned product.
QP2724-QP2834-SIGMA-OneBlade_US_3000.092.1303.2_LFLT_folded96x171mm_BW.indd 1,4-7QP2724-QP2834-SIGMA-OneBlade_US_3000.092.1303.2_LFLT_folded96x171mm_BW.indd 1,4-7 27-10-22 10:0527-10-22 10:05
Loading ...
Loading ...
Loading ...