ENGLISH
IMPORTANT
SAFETY
INSTRUCTIONS
When using an electric product,
basic precautions should always be
followed, including the following:
Read all instructions before using this
product.
DANGER
To reduce the risk of electric shock:
- Do not reach for a corded product
or charging stand that has fallen
into water. Unplug immediately.
- The power cord and the accessories
connected to it are not for
immersion or for use in shower.
- Do not use an extension cord with
this product.
- Do not place or store the product
or charging stand while plugged in
where it can fall or be pulled into a
tub or sink. Do not place or drop the
product or charging stand water or
other liquid while plugged in.
- Always unplug this product and
charging stand from the electrical
outlet immediately after (re)charging.
- Unplug and remove power supply
cord from this product or charging
stand before cleaning.
- The batteries used in this product
may present a re or chemical
burn hazard if mistreated. Do not
disassemble, heat above 100 °C
(212 °F) or incinerate.
WARNING
To reduce the risk of burns, re,
electric shock, or injury to persons:
- Close supervision is required when
this product and charging stand
are used by, on, or near children,
or persons with limited physical,
sensory, or mental capabilities or
invalids.
- Use this product and charging stand
for its intended household use as
described in this manual. Do not
use attachments not recommended
by Philips Electronics North America
Corporation.
- Never operate this product or
charging stand if it has a damaged
power cord, if it is not working
properly, after it has been dropped
or damaged, or dropped into water
while plugged in. For assistance call
1-800-243-3050.
- Keep the product, power cord,
charging stand and any attachments
away from heated surfaces.
- Never drop or insert any object into
any opening.
- Do not use the adapter in or near
a power outlet that contains an
electric air freshener to prevent
damage to the adapter.
- Do not charge, clean or plug in
product outdoors or operate where
aerosol (spray) products are being
used or where oxygen is being
administered.
- Always check blade and comb
before using the product. Do not
use the product if blade or comb
are damaged, as injury may occur.
- Always attach power cord to
product or charging stand rst, then
to power outlet. To disconnect, turn
product o then remove power
cord from outlet.
- Keep the power cord and charging
stand dry at all times. Do not handle
with wet hands.
- Never put the product or charging
stand in direct sunlight or store at a
temperature above 140 °F (60 °C).
- To prevent possible damage to the
power cord, do not wrap power
cord around the product.
- This product is for use on human
hair only. Do not use the product for
any other purpose.
- Always store the product, attachments
and power cord in a moisture-
free area. Make sure the cord is
disconnected from the product.
- Do not attempt to open the product
to remove or replace the built-in
rechargeable battery.
- Only use the power cord and other
accessories supplied with the product.
SAVE THESE
INSTRUCTIONS
IMPORTANT: The power plug contains a
transformer. Do not cut o the power plug
to replace it with another plug as this will
cause a hazardous condition.
Introduction
Congratulations on your purchase and
welcome to Philips Norelco!
To fully benet from the support that
Philips Norelco oers, register your
product at www.philips.com/register.
1
2
3
4
5
7
6
8
9
13
12
11
10
3mm/1/8 in.
15
14
16
1
General description (Fig. 1)
1 OneBlade (for face)
2 Blade release slide switch
3 Travel lock
4 Battery status percentage
5 Charge symbol
6 LED Digital display
7 On/o button
8 Charging stand
9 Small plug of the charging stand
10 Small plug
11 Power plug
12 14-length Precision trimming comb
13 Hair length setting wheel
14 OneBlade (for body)
15 Click-on skin guard
16 Click-on body comb 3mm (1/8 in.)
Not shown: pouch
This symbol indicates that the
product can be used in the bath
or shower.
432
75 6
1098
1311 12
1 2
161514
1
2
1917 18
1
2
222120
3 sec.
2523 24
282726
2
1
3129 30
32 33
Charging
Charging takes approx. 1 hour.
Charge the product before rst use and
when the display indicates that the battery
is almost empty.
- Charging or using the product at
temperatures below 40 °F (4,5 °C) or
higher than 95 °F (35 °C) adversely
aects the lifespan of the battery.
- If the product is subjected to a major
change in temperature, pressure or
humidity, let the product acclimatize for
30 minutes before use.
Battery status indications
- When the product charge is almost
empty, the charge symbol ashes
orange (Fig. 2).
- The remaining battery capacity
is indicated by the battery status
percentage on the display.
- When the product is charging, the
charging symbol ashes white (Fig. 3).
- Quick charge: after approx. 5 minutes
charging, the product contains enough
energy for 5 minutes use. During quick
charge the charge symbol quickly blinks
white until quick charge is nished.
- When the battery is fully charged,
the battery status percentage shows
100 % and the charge symbol lights up
continuously.
Note: Approx. 30 minutes after the
battery is fully charged or when you
disconnect the product from the outlet,
the battery status indicator switches o
automatically.
Charging with the power cord
1 Make sure the product is switched o.
2 Insert the small plug into the product
and put the power plug in any 120 V AC
outlet (Fig. 4).
3 After charging, remove the power plug
from the wall outlet and pull the small
plug out of the product.
Charging in the charging stand
1 Insert the small plug into the charging
stand and put the power plug in any
120V AC outlet (Fig. 5).
2 Put the product in the charging stand
(Fig. 6).
3 After charging, remove the power plug
from the wall outlet and pull the small
plug out of the charging stand.
Operating time
When the product is fully charged, it has a a
cordless operating time of up to 90 minutes.
Note: An adapter plug may be necessary
for cord usage in some foreign countries.
Use an attachment plug adapter of the
proper conguration for power outlet.
Using the product
This product comes with 4 blades. Use two
blades for your face only and the other
blades for your body.
14-length precision comb is for use on
facial hair. It is not intended for shaving,
edging or trimming hairs on lower body
parts or scalp hair. Body
comb is for use
on body parts below the neck.
The blade with the skin guard attached is for
use on sensitive body areas.
Note: This product is for cordless use only
(Fig. 7).
- Use this product for its intended
household use as described in this
manual.
- For hygienic reasons, the product
should only be used by one person.
- Trimming is easier when the skin and
hair are dry.
- Use the product with the face blade to
trim, edge or shave facial hair (beard,
mustache and sideburns). Shave for a
smooth result, trim with the precision
comb to obtain a certain length and
edge to create perfect edges and
sharp lines.
Manufactured for:
Philips Personal Health
A division of Philips North America LLC
P.O. Box 10313, Stamford, CT 06904
This symbol on the product’s nameplate means
it is listed by Underwriters’ Laboratories, Inc.
Norelco is a registered trademark of
Philips Electronics North America Corporation.
PHILIPS and Philips shield are registered trademarks of
Koninklijke Philips N.V.
©2019 Philips North America LLC
All rights reserved.
4222.002.9126.1 (05/2019)
QP6620
QP6620
- Use the product with the body blade to
trim and/or shave your body hair. Shave
your chest by only using the blade.
Shave your sensitive areas (e.g. groin,
armpits) with the skin guard attached.
Use the body comb to trim your body hair.
- Take your time when you rst start to
use the product. You have to acquire
practice with the product.
Switching the product on and o
1 Press the on/o button once to switch
the product on or o (Fig. 8).
Shaving
- Make sure that the blade is in full contact
with the skin by placing it at on the skin.
- For the best result, move the product
against the grain.
- Make long strokes while pressing lightly.
- Use the product dry or wet with gel or
foam, even in the shower.
- Shaving a clean beard and face gives
the best results.
1 Switch the product on (Fig. 8).
2
Place the blade on the skin and move the
product up or against the grain in long
strokes while pressing lightly (Fig. 9).
Note: Make sure you hold the surface of
the blade at against your skin (Fig. 10).
3 Switch o and clean the product after
every use (see ‘Cleaning’).
Edging
- Use both edges of the blade to create
sharp lines and perfect edges.
- Hold the product in such a way that
the blade is perpendicular to the skin
and one of its edges touches the skin.
This allows more precise detailing of
sideburns and the area around the
mouth and nose.
1
To create sharp edges and lines, you can
use either edge of the blade
(
Fig. 11).
2 Switch the product on (Fig. 8).
3 Place the edge of the blade
perpendicular onto the skin (Fig. 12).
4 Make straight strokes while applying
gentle pressure (Fig. 13).
5 Switch o and clean the product after
each use (see ‘Cleaning’).
Trimming with comb
- The precision trimming comb allows
you to trim hair to dierent lengths.
When you trim for the rst time, start at
the highest length setting to familiarize
yourself with the product.
- Always trim in the direction of the
teeth of the precision trimming comb
making sure the at part of the comb is
in full contact with the skin for an even
trimming result (Fig. 15).
- Since all hairs do not grow in the same
direction, you may want to try dierent
trimming positions (i.e. upwards,
downwards, or across). Practice is best
for optimum results.
- Make sure to always move the product
against the grain.
- Trimming is easier when the skin and
hair are dry.
1 Place the front part of the comb
ontothe blade and push the projection
at the back of the comb into the
product (‘click’) (Fig. 16).
2 Turn the hair length setting wheel to
select the desired hair length setting
(Fig. 17).The settings on the wheel
correspond to the remaining hair length
after trimming. You can select a length
from 1/32 in./0.4 mm to 13/32 in./10 mm
(Fig. 14).
3 Switch the product on (Fig. 8).
4 Place the comb onto the skin and move
the product upwards slowly, against the
grain (Fig. 18).
5 Switch o and clean the product after
each use (see ‘Cleaning’).
6 To remove the comb, pull the back part
o the product and then slide the comb
o the blade (Fig. 19).
Body
- For hygienic reasons, only use the body
blade for trimming and shaving your
body.
- For body trimming and shaving, make
sure hair is clean and dry as wet hair
tends to stick to the body.
- When shaving sensitive areas, always
use the skin guard.
- Since all hairs do not grow in the same
direction, you may want to try dierent
trimming positions (i.e. upwards,
downwards, or across). Practice is best
for optimum results.
- For the best result, move the product
against the grain.
- Make long strokes while pressing lightly.
- You can also use the product dry or wet
with gel or foam, even in the shower.
- Shaving a clean body gives the best
results.
Shaving with skin guard
For optimal performance, use the skin
guard only on sensitive areas (for example
the groin and armpits).
1
Hold the skin guard on both sides and
press onto the blade (Fig. 20).
2 Switch the product on (Fig. 8).
3 Place the skin guard onto the skin and
stretch the skin with your free hand.
Move the product upwards slowly,
against the grain (Fig. 21).
- When using the product on your
armpits, raise your arm and put your
hand on the back of your head to
stretch the skin.
- Regularly remove cut hair from the
guard. If a lot of hair has accumulated
in the guard, remove it from the
product and blow and/or shake out
the hairs.
4
Switch o and clean the product after
each use.
5 To remove the skin guard, put one
nger under the edge of the guard and
press on the blade with your thumb
(Fig. 22).
Shaving without skin guard
The body blade without the skin guard
allows you to shave hair on your body
below the neckline (for example the chest).
1
To remove the skin guard, put one nger
under the edge of the guard and press
with your thumb on the blade (Fig. 22).
2 Switch the product on (Fig. 8).
3 When you use the product on your chest,
place the blade on the skin and move the
product against the grain in long strokes
while pressing lightly. Stretch the skin
with your free hand (g. 24).
Note: Make sure you hold the surface of
the blade at against your skin (Fig. 10).
4 Switch o and clean the product after
every use (see ‘Cleaning‘).
Trimming with body comb
The 3 mm (1.8 in.) body comb allows you to
trim hair on your body below the neckline
(for example chest, armpits, groin).
1 Hold the body comb on both sides and
press onto the blade (Fig. 23).
2 Switch the product on.
3 Place the comb onto the skin and
stretch the skin with your free hand.
Move the product upwards slowly,
against the grain (Fig. 24).
- Make sure that the at part of the
comb is always in full contact with
the skin to obtain an even trimming
result (Fig. 15).
- When you use the product on your
armpits, raise your arm and put your
hand on the back of your head to
stretch the skin.
- Regularly remove cut hair from the
guard. If a lot of hair has accumulated
in the guard, remove it from the
product and blow and/or shake out
the hairs.
4 Switch o and clean the product after
each use (see ‘Cleaning‘).
5 To remove the comb, hold it on both
sides and pull it o the blade (Fig. 22).
Travel lock
The product is equipped with a travel lock
function. You can use the travel lock if you
are going to store the product for a longer
time period or if traveling. The travel lock
prevents the product from being switched
on by accident.
Activating the travel lock
1 Press the on/o button for 3 seconds
(Fig. 25).
- The travel lock symbol lights up and the
digital display counts down (Fig. 26).
- When the travel lock is activated,
the travel lock symbol ashes.
Deactivating the travel lock
1 Press the on/o button for 3 seconds
(Fig. 25).
- The display counts down. Then the
travel lock symbol lights up and
switches o (Fig. 27).
- The product is now ready for use.
Note: The product unlocks automatically
when connected to an electrical outlet.
Cleaning
Clean the product after every use.
Never use scouring pads, abrasive cleaning
agents or aggressive liquids such as
gasoline or acetone to clean the product.
Do not tap the product or blade against a
surface to remove hairs and water as this
may cause damage to the product and
blade (Fig. 28). If the blade is damaged,
replace immediately.
Never dry the blade with a towel or
tissue, as this may cause damage.
Cleaning the product
1 Switch o the product.
2
Remove the comb from the blade (Fig. 19).
3 Blow o any hairs that have
accumulated on the blade and/or comb.
4
Switch on the product approx. 15 seconds
while rinsing the blade with lukewarm
water.
5 Rinse the comb for approx. 15 seconds
with lukewarm water.
6 Carefully shake o excess water and let
all parts air dry completely.
Note: The blade is fragile. Handle it
carefully. Replace the blade immediately if
it is damaged.
This product has no other user-serviceable
parts. For assistance call 1-800-243-3050.
Storage
- Always attach the precision trimming
comb on the blade to protect the blade
from damage during traveling or storage
(Fig. 16).
- Store the product in the pouch
supplied. Make sure the product and
attachments are completely dry before
storing in the pouch.
- Be sure the product is switched o.
Remove cord from outlet and the
product before storing it in a safe, dry
location where it will not be crushed,
banged, or subject to damage.
- Do not wrap cord around the product
when storing.
- Store cord in a safe location where it
will not be cut or damaged.
- Do not place or store the product where
it can fall or be pulled into a tub or sink,
water or other liquid while plugged in.
Replacement
Replacing the blade
For optimal cutting and gliding
performance, replace the blade every
4 months or when it no longer provides
the shaving or trimming results you expect.
This advice is based on two full shaves a
week and actual results may vary.
The blade is equipped with a blade
wear indicator. A green bar will gradually
appear on the blade as you use it. When
it is highly visible, it is recommended to
replace your blade for the best OneBlade
experience. Always replace the blade with
original Philips Norelco blade
(see ‘Accessories’).
Depending on your usage behavior, the
exact lifetime of the blade could be longer
or shorter. Similar to a manual blade, the
blade becomes blunt over time, which
results in increased hair pulling and
reduced cutting performance.
Replacing the blade
1 Switch the product o.
2 Carefully push the blade release slide
switch upwards while holding the blade
on both sides (Fig. 31). This will prevent
the blade from ying away.
3 Hold the new blade on both sides and
press it onto the handle (‘click’) (Fig. 32).
Note: Be careful, the edges of the blade
are sharp. When you hear a click, the new
blade is placed correctly and ready for use.
Accessories
Replacement parts and accessories may
be purchased at a store near you or on our
website www.philips.com/store.
The following accessories are available:
- Model QP210 Philips Norelco
Replacement Blade, 1-Pack
- Model QP220 Philips Norelco
Replacement Blade, 2-Pack
- Model QP230 Philips Norelco
Replacement Blade, 3-Pack
Assistance
For assistance, visit our website:
www.philips.com/support or call toll free
1-800-243-3050.
Online information is available 24 hours
a day, 7 days a week.
Disposal
- This product contains a rechargeable
lithium-ion battery which must be
disposed of properly (Fig. 33).
- Contact your local town or city ocials
for battery disposal information. You
can also call 1-800-822-8837 or visit
www.call2recycle.org for battery
drop-o locations.
- For assistance, visit our website
www.philips.com/support or call
1-800-243-3050 toll free.
- Your product is designed and
manufactured with high quality
materials and components, which can
be recycled and reused. For recycling
information, please contact your local
waste management facilities or visit
www.recycle.philips.com
Full Two-Year Warranty
Philips North America LLC warrants this
new product (except blade and 14-length
precision comb) against defects in
materials or workmanship for a period of
two years from the date of purchase, and
agrees to repair or replace any defective
product without charge.
IMPORTANT: This warranty does not
cover damage resulting from accident,
misuse or abuse, lack of reasonable
care, the axing of any attachment not
provided with the product or loss of parts
or subjecting the product to any but the
specied voltage or batteries.*
NO RESPONSIBILITY IS ASSUMED
FOR ANY SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES.
In order to obtain warranty service,
simply go to www.philips.com/support
for assistance. It is suggested that for
your protection you return shipments
of product by insured mail, insurance
prepaid. Damage occurring during
shipment is not covered by this warranty.
NOTE: No other warranty, written or oral, is
authorized by Philips North America LLC.
This warranty gives you specic legal
rights, and you may also have other rights
which vary from state to state. Some states
do not allow the exclusion or limitation of
incidental or consequential damages, so
the above exclusion and limitations may
not apply to you.
*Read enclosed instructions carefully.
45-DAY MONEY-BACK GUARANTEE
If you are not fully satised with your
product send the product back and we’ll
refund you the full purchase price.
The product must be shipped prepaid
by insured mail, insurance prepaid, have
the original sales receipt, indicating
purchase price and date of purchase,
and the money-back guarantee return
authorization form enclosed.
We cannot be responsible for lost mail.
The product must be postmarked no later
than 45 days after the date of purchase.
Philips reserves the right to verify the
purchase price of the product and limit
refunds not to exceed suggested retail price.
To obtain the money-back
guarantee service, please go to
www.PhilipsMoneyBack.com,
and follow the simple 3 step process.
Delivery of refund check will occur 6–8
weeks after receipt of returned product.
