Dewalt DWST08060 Instruction Manual

Loading ...

ENGLISH

The label on your tool may include the following symbols. The

symbols and their definitions are asfollows:

V ......................... volts

Hz .......................hertz

min ..................... minutes

or DC ......direct current

...................... Class I Construction

(grounded)

A ......................... amperes

W ........................watts

Wh ......................watt hours

Ah ....................... amp hours

or AC ........... alternating current

or AC/DC .... alternating or direct

current

...................... Class II Construction

(double insulated)

......................earthing terminal

.....................safety alert symbol

.....................hot surface

..................... visible radiation–

do not stare into

the light

..................... wear respiratory

protection

..................... wear eye protection

..................... wear hearing

protection

..................... r

ead all documentation

.....................

do not expose to rain

Minimum Gauge for Cord Sets

Volts

Total Length of Cord in Feet

(meters)

120 V 25 (7.6) 50 (15.2) 100 (30.5) 150 (45.7)

240 V 50 (15.2) 100 (30.5) 200 (61.0) 300 (91.4)

Ampere Rating

American Wire Gauge

Than

Not

Than

0 6 18 16 16 14

6 10 18 16 14 12

10 12 16 16 14 12

12 16 14 12 Not Recommended

Additional Safety Information



WARNING: Never modify the power tool or any part of

it. Damage or personal injury couldresult.



WARNING: ALWAYS use safety glasses. Everyday

eyeglasses are NOT safety glasses. Also use face or

dust mask if cutting operation is dusty. ALWAYS WEAR

CERTIFIED SAFETYEQUIPMENT:

• ANSI Z87.1 eye protection (CAN/CSA Z94.3),

• ANSI S12.6 (S3.19) hearing protection,

• NIOSH/OSHA/MSHA respiratoryprotection.

• An extension cord must have adequate wire size

(AWG or American Wire Gauge) for safety. The smaller

the gauge number of the wire, the greater the capacity

of the cable, that is, 16gauge has more capacity than

18gauge. An undersized cord will cause a drop in line

voltage resulting in loss of power and overheating. When

using more than one extension to make up the total length,

be sure each individual extension contains at least the

minimum wire size. The following table shows the correct

size to use depending on cord length and nameplate

ampere rating. If in doubt, use the next heavier gauge. The

lower the gauge number, the heavier thecord.

• Before using work light, read all instructions

and cautionary markings on work light, charger

andbattery.

• Store the work light indoors when not in use. Keep out

of reach ofchildren.

• Make sure extension cord is located so that it will not

be stepped on, tripped over, or otherwise subjected to

damage orstress.

• Use only a proper extension cord that is necessary to

operate the work light on AC power (refer to Use of

Extension Cords with work light). Use of an improper

extension cord could result in risk of fire, electric shock,

orelectrocution.

• A proper extension cord will be marked with the suffix

letter "W" and with a tag stating "Suitable for Use

with Outdoor Appliances."

• Place the work light away from any heatsource.

• Do not disassemble work light. Take it to an authorized

service center when service or repair is required. Incorrect

reassembly may result in a risk of electric shock,

electrocution orfire.

• Disconnect the work light from the outlet before

attempting any cleaning. This will reduce the risk of

electric shock. Removing the battery pack will not reduce

thisrisk.

• Use type SJW, SJOW, SJTW, SJTOW, SW, SOW, STW

and STOW cord when operating the Work light on

ACpower.

Wireless Certifications andSafetyInformation

• This device is either CAN ICES-3(B)/NMB-3(B)or CAN ICES-

5(B)/NMB-5(B)compliant.

• This device complies with Part 15 of the FCC Rules and

Industry Canada License-exempt RSS standard(s). Operation

is subject to the following two conditions: 1) This device may

not cause harmful interference, and 2) This device must accept

any interference received, including interference that may

cause undesiredoperation.

This equipment has been tested and found to comply

with the limits for a Class B digital device, pursuant to Part

15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and

can radiate radio frequency energy and, if not installed

and used in accordance with the instructions, may cause

harmful interference to radio communications. However,

there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be

determined by turning the equipment off and on, the user

is encouraged to try to correct the interference by one or

more of the followingmeasures: 1)Reorient or relocate the

receivingantenna, 2) Increase the separation between the

equipment andreceiver, 3) Connect the equipment into an

outlet on a circuit different from that to which the receiver

isconnected or 4) Consult the dealer or an experienced radio/

TV technician forhelp.

Loading ...

Dewalt DWST08060 TOUGHSYSTEM 2.0 ADJUSTABLE WORK LIGHT WITH STORAGE

Instruction Manual - Page 7