Loading ...
Loading ...
Loading ...
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity before servicing. Check appliance is safe when you have nished.
33
Reassemble in reverse order, making sure that the leads are
reconnected.
Check for correct burner operation.
2.2 To Change a Hotplate Tap
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the hotplate top (see 2.1). Unplug the FSD lead from the
rear of the tap and undo the compression tting. Remove the xings
that secure the tap to the gas rail. Remove the tap. Remove and
discard the gasket seal.
Fit the new gasket seal to the replacement tap. Reassemble in
reverse order.
Make sure that the valve is adjusted for correct gas operation. Check
that the cooker is gas sound. Check hotplate ignition.
2.3 To Replace a Hotplate Burner Jet
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the burner cap and head (Fig. 10.4). Remove the old jet. Fit
the new orice.
Note: The wok burner has 2 orices.
Reassemble in reverse order. Check that the appliance is gas sound.
2.4 To Change a Hotplate Burner Electrode
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Lift o the pan supports and remove the burner cap. Remove
the screw holding the electrode. Pull the electrode vertically up
suciently to grip the lead between thumb and forenger. Pull o
the electrode, but keep hold of the lead.
Fit the new electrode to the lead. Fix the electrode in the burner
with the screw. Replace the burner cap.
Check the burner ignition. Replace the pan supports.
2.5 To Change a Hotplate Burner Thermocouple
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel and hotplate (see 1.2 & 2.1).
Unplug the FSD lead from the rear of the tap.
The thermocouple sits in a hole that has a slot at one side. Ensure
that the thermocouple is cool. Turn the thermocouple so that the
earth lead (no sleeve) is in line with the slot. Lift the thermocouple
clear of the hole.
Reassemble in reverse order.
2.6 To Remove or Change a Hotplate Burner
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the hotplate top (see 2.1). Remove the control panel (see 1.2).
Centre Hotplate Burners
The burners are mounted in pairs on the cross supports. Disconnect
the burner feed pipes at the burners. Remove the screw at the front
holding the cross support (Fig. 10.5). Slide the support to the right
to release it from the rear location.
Lift the cross support and burners clear. The burners are xed to the
cross supports with screws underneath. Remove the appropriate
burner and t the new one.
Reassemble in reverse order. Check that the burner operation is
satisfactory.
Wok Burners
Disconnect the burner feed pipes at the burner. Fit the new one
and reassemble in reverse order. Check that the burner operation is
satisfactory.
3 Controls
3.1 To Change Ignition Generator
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Pull the cooker forward to gain access to the cover box at the rear of
the left-hand oven. Remove the screws securing the cover and lift
clear. Pull o all the leads to the generator, noting their positions.
Slacken the 2screws holding the generator to the cooker and
remove the generator.
Fit the new generator to the cooker and replace the leads, referring
to the wiring diagram.
Reassemble in reverse order. Check ignition performance.
3.2 To Replace the Light Switch
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel (see 1.2).
Note: The old switch may be destroyed during removal.
Remove the old switch from its bezel by gripping the switch body
behind the control panel and twisting sharply. Remove the switch
bezel by folding back its locking wings and pushing forward.
Fit the new bezel to the control panel by rst lining up the raised key
on its body with the cut-out in the control panel and pushing it in
from the front.
Assemble the new switch to the bezel by lining up the key sections
and pushing home. Fit the new button by pushing in from the front.
Replace the control panel in reverse order and test for correct
operation.
Loading ...
Loading ...
Loading ...