Loading ...
Loading ...
3
There are several things to consider when choosing the appropriate location to install your waterfall.
The waterfall is designed to be installed into a 2” x 4” interior wall. The waterfall should not be installed in a load bearing wall, unless it
can be framed in with proper supports and headers as required by your local building codes. Check with your local building authority for
specifications. Installing the waterfall in an exterior wall is not recommended, as it cannot be properly insulated. If there are no suitable
alternative locations, then the waterfall can be installed in a 2” x 6” wall using rigid foam insulation between the exterior of the house and the
back of the fountain. The waterfall cannot be installed in a 2” x 4” exterior wall.
The see-thru waterfall only has water running down one side of the glass, so thought should be given as to which direction the unit is
mounted. The side with the manifold is the side with the water flow. The see-thru waterfall is not designed to be air tight like a window and
cannot be placed on an exterior wall. If being placed between rooms where privacy may be a concern, a clouded or patterned glass can be
used. Some noise will also travel between the two rooms that share the waterfall.
The lights, pump and optional UV-light require power. Make sure you choose a location that has the available power within reach of the
supplied electrical cords. The receptacle must be GFI (ground fault interrupt) protected. Electrical work must be done by a qualified electrician.
Check with your local building authority for specifications for your area. Do not run extension cords behind walls.
An area to locate the pump module is also required. It should be located as close to the fountain as possible and in a location
that is easily accessible for servicing and maintaining the module. Although we recommended that the pump module and the
waterfall be located as close as possible to each other we have specified some maximum heights which you must follow. Maximum height
from floor on which pump module is sitting to top edge of waterfall frame is 12 feet. The maximum horizontal distance from drain outlet on
waterfall to drain inlet on pump module is 15 feet. For every 1 foot that the pump module is located away from the fountain unit, 1 inch of
drop is required from the fountain basin drain outlet to the pump module drain inlet. With longer lines there are a few other things to
consider, the drain needs to have a constant slope from the waterfall outlet to the pump module inlet, if there are dips or rises the drain will
gurgle. A lot more water is held in the lines, this means that there is a large difference in the level of water in the reservoir from when the
unit is off, to when the unit is operating. To eliminate any potential problems such as unit overflowing or running dry, the unit must be
hooked up to both a water supply and a drain.
The waterfall is designed to be connected to a water source, to automatically refill the basin as water evaporates, and to a drain, in case
of accidental overflow. The unit can be operated without the water source connection, but is not recommended. The water will evaporate
naturally and will require additional water to ensure proper flow and pump operation. Damage to the pump incurred by running dry is not
covered by warranty. The waterfall must be hooked-up to a drain which will allow the tank to be purged for routine cleaning, and will
prevent the unit from overflowing if the float valve malfunctions.
Water damage to surrounding objects in your home is not covered in your NAPOLEON warranty. The waterfall is designed to not splash,
however if it is not properly installed or maintained, some splashing may occur. Protect delicate nearby surfaces that could be damaged by
splashing. Do not trim with materials that can be damaged by moisture such as particle board or MDF. It is best to install the unit in stone,
marble, glass, tile etc.
Although your NAPOLEON Waterfall will be beneficial to the air quality of your home, excess moisture can lead to the formation of mold and
mildew. It is recommended that all homes have some form of humidity control and air exchange system to prevent such an occurence.
Tools:
- utility knife
- adjustable wrench
- 3/8” nut driver
- pliers
- flat screw driver
installation Tools and materials required
Materials:
- saddle valve and 1/4” tubing (ice maker plumbing kit) (required if unit is being con-
nected to house water supply)
- teflon tape
- possible additional 1/2” i.d. tubing and 3/4” i.d. tubing depending on location of unit.
- liquid TSP (Trisodium Phosphate) or TSP Substitute cleaner
Before you begin hooking up the fountain ensure that you have access to the following materials and tools.
indoor air quality
Your new NAPOLEON waterfall will dramatically improve the indoor air quality in your home. The waterfall is a natural
humidifier which helps alleviate dry skin and allergies. This is extremely beneficial in dry climates and also cold climates
where forced air furnaces dry the air. The waterfall also cleans the air by attracting contaminants. Moving water attracts
airborne particles, such as dust, pet dander, pollen and other pollutants. The waterfall draws these particles into the water,
which is then filtered through a 5 micron filter before being recirculated. The result is cleaner, fresher, humidified air.
Waterfalls also generate negative ions. These odourless tasteless invisible molecules are created in nature as air
molecules break apart due to sunlight, radiation, and moving air and water. Researchers now believe that negative ions aid
in alleviating depression, reducing stress and boosting energy.
appropriate location
Loading ...
Loading ...
Loading ...