Loading ...
Loading ...
Loading ...
Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bottom of the mounting plate
touch the bottom of the cabinet when pushed
flush against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
3
4
ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate
through the holes designated to go into drywall
and reattach the toggle wings to
3
⁄4″ (19 mm) onto
each bolt.
1
INSTALLATION OVERVIEW
Attach Mounting Plate to Wall
Prepare Top Cabinet
Mount Microwave Oven
Adjust Exhaust Adaptor
Wall
M ounting
Plate
Spacing for Toggles
M ore Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
Installation Instructions
2
OUTSIDE TOP EXHAUST (Vertical Duct)
IMPORTANT NOTES:
• Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
• Make sure the motor wiring has
been properly routed and secured,
and that the wires are not pinched.
. Connect Ductwork
Check Damper Operation
Adapting Microwave Blower for
Outside Top Exhaust
C
C2.
C1.
C3.
C4.
C6.
C5.
C7
C1.
3/
8"
TO
EDGE
NOTE
:
IT IS
VERY IMPO
R
TANT TO
READ AND FO
LLOWTHE D
IRECTIO
N
S
IN THE INSTALLATION INSTRU
CTI
O
N
S
BE
FO
RE PRO
CEEDING
WITH TH
IS
REAR WA
LL TEMPLA
TE.
Thi
s
R
ea
rWa
ll Templa
te serves to p
ositio
n
the bo
tto
m
mou
ntin
g p
l
a
te
and
to l
oc
ate the hor
iz
ontal exhau
s
t
ou
tlet.
1. Use a levelto
check tha
t the t
emplate i
s
positioned
ac
cu
r
a
tely.
2. L
oc
ate a
ndma
r
k at lea
st o
nestud on the left or
right
s
id
e of the centerli
ne
.
It is importa
nt to u
s
e a
t le
as
t
one
wood
sc
rew
mounted
fi
rmly in
a
stud to suppor
t the w
eight
of
th
e mic
r
owav
e.
M
ar
k t
wo
a
d
dition
al, evenly
spac
ed
locations
f
o
r
the
s
upplied toggle bolts.
3. Dr
i
ll hole
s in
th
e
marked locations.Wher
e ther
e is
a s
tu
d,
drill
a 3/1
6" h
ole fo
r wood screw
s. Fo
r ho
les
th
atdo not line up
w
ith a stu
d, d
rill 5/8
" holes fo
r
to
ggle bolts.
DO NOT
IN
S
T
AL
L THE MO
UNTING P
LATE
AT THIS
T
IME.
4. Re
m
o
v
e
the template fr
o
m
the r
ea
r wall.
5.Review the Ins
ta
llationInstr
ucti
o
n bo
ok for you
r
instal
l
a
ti
on situation.
Locate and m
ar
k holes
to ali
gn with holes in t
he
mounting
p
late.
IMP
O
RTANT
:
LO
C
AT
E
AT LEA
ST ONE STUD
ON EI
T
HERSID
E O
F
THE CENTE
R
LI
N
E.
MARK
THE LO
CATIONF
O
R 2 ADDIT
IO
NAL, EVENLY
SPACED T
OGGLE
BOLTS IN THE MO
UNTING
PLATE
AREA
.
Locate and mark
holes
to al
i
gn with holes
in t
he
mountingplate.
IMPORTANT:
LO
C
A
TE AT LEA
ST O
NESTUD ON EITHER SI
D
E OF
THE
CENTE
R
LINE
.
MARKTHE LO
CATION
FOR 2 ADDITIONA
L, EV
ENLY
SPACEDTOG
GLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the re
ar
wall tem
plate along
the dotted
line.
Trim the rear
wall templat
e along
t
he dotted lin
e.
12"
4"
Da
rl
e
v
ue
lt
a
ala
hoj
a
par
a
co
ns
u
ltar
la
ver
sió
n
enEs
pa
ñol.
EN-20
Loading ...
Loading ...
Loading ...