Loading ...
Loading ...
Loading ...
INSTALLATION OVERVIEW
Attach Mounting Plate to Wall
Prepare Top Cabinet
Mount the Microwave Oven
IMPORTANT NOTES:
• Make sure the screws for the blower motor and blower
plate are securely tightened when they are reinstalled.
This will help to prevent excessive vibration.
• Make sure the motor wiring has been properly routed
and secured, and that the wires are not pinched.
Installation Instructions
Place the mounting plate against the wall and
insert the toggle wings into the holes in the wall
to mount the plate.
NOTE: Before tightening toggle bolts and wood
screw, make sure the bott m of the mounting plate
touch the bottom of the cabinet when pushed flush
against the wall and that the plate is properly
centered under the cabinet.
CAUTION: Be careful to avoid pinching fingers
between the back of the mounting plate and the wall.
Tighten all bolts. Pull the plate away from the wall
to help tighten the bolts.
4
3
ATTACH THE MOUNTING
PLATE TO THE WALL
Attach the plate to the wall using toggle bolts.
At least one wood screw must be used to attach
the plate to a wall stud.
Remove the toggle wings from the bolts.
Insert the bolts into the mounting plate through
the holes designated to go into drywall and
reattach the toggle wings to
3
⁄4″ (19 mm) onto
each bolt.
1
Wall
M ounting
Plate
Spacing for Toggles
M ore Than Wall
Thickness
Bolt End
Toggle
Bolt
Toggle Wings
To use toggle bolts:
2
RECIRCULATING (Non-Vented Ductless)
Install or change Charcoal Filter
Check Blower Plate
NOTE:
If the cabinet depth including the cabinet doors
is more than 13""'' then the unit must be spaced
o
A
A1.
A2.
A3.
A4.
A5.
A1.
Cabinet
Cabinet
(33 cm)
13" MAX.
out from wall using adequate materials supporting
150 Ibs to allow proper top vent air exhaust/intak
e.
3/8"TO
EDG
E
NO
TE
: IT IS VERY IM
POR
TANT TO
READ AND FOLLO
W
THEDIRECTIONS
IN THE INSTALLAT
ION INSTRUCTIONS
BE
F
O
RE PR
O
CEEDINGWITH TH
IS
REAR W
ALL TEMPLAT
E.
T
hi
s Rear
Wall Template serves to position
the bottom
mounting plateand to l
o
cate th
e h
or
i
zontal ex
hau
st
out
le
t.
1
. Us
e a le
velto check that the t
emplate is p
os
ition
ed
accuratel
y
.
2. L
oca
te a
ndm
ark at le
a
s
t onestu
d
on theleft or
right
side of the c
e
nterli
ne
.
It is import
an
t to use at le
as
t
one
wood
scre
w
mou
nte
d
fi
rmly in a
s
tud to suppor
t th
e weight
ofth
e micr
ow
ave
.
Mark two addi
tional, evenlyspa
c
ed
locatio
n
s for the
supplied toggle
bo
lts.
3. Drill hole
s in the
marked locations.Whe
r
e t
he
re is
a
stu
d
, d
r
ill a 3/16" hole
for woo
d screws. For holes
thatdo not line up with a s
tu
d, drill 5/8" h
oles fo
r
toggle bolts.
DO NOT INSTALL T
HE
MOU
NT
I
NG
PLA
T
E
A
T
THIS
T
IME.
4. Re
move the template fromthe r
ear
wal
l.
5.Revie
ht
w e In
sta
llationInstr
uc
tion book for
y
our
in
stallation
s
i
tuation.
Locate and mark holes to align with holes in the
mounting
p
late.
IMPO
RTANT
:
LO
C
AT
E AT LEAST
O
N
E STUD
ON EIT
HER
SID
E OF
TH
E CENTERLIN
E
.
MARKT
HE LO
CATION
FO
R 2 ADDITIONAL, EVENLY
SPACE
D TOGGLE BOLTS
IN
THE MOUNTING
PLATE
AREA
.
Locate and mark
holes to ali
gn with holes
in the
.
e
ta
lp
gn
itn
u
o
m
IMPO
RTANT
:
LOCAT
E AT LEAST ON
ESTUD ON EITHER SI
DE OF
THE
CENTER
LIN
E.
MARKT
HE LOCATIONFO
R 2 ADDITION
AL, EV
ENLY
SPACED
TO
G
GLE BO
LTS IN
THE MO
UN
TING PLATE
AREA
.
Trim t
he rear wall templat
e along
t
he do
tted line.
Trim the rear
wal
l t
emplat
e along
the dotted lin
e.
12"
4"
Darlevu
eltaa la ho
j
apara
c
o
nsul
t
a
r
la
v
e
r
s
i
ó
ne
nEs
paño
l.
EN-10
Loading ...
Loading ...
Loading ...