Loading ...
Loading ...
Loading ...
INSTALLATION OVERVIEW
B1. Prepare Rear Wall
B3. Attach Mounting Plate to Wall
B4. Prepare Top Cabinet
B5. Adjust Blower
B6. Mount the Microwave Oven
IMPORTANT NOTES:
• Make sure the screws for the
blower motor and blower plate
are securely tightened when
they are reinstalled. This will
help to prevent excessive
vibration.
•
been properly routed and secured,
and that the wires are not pinched.
Remove and save the screw that holds the blower
plate to the microwave. Lift off the blower plate.
Back of
M icrowave
Installation Instructions
PREPARING THE REAR WALL
FOR OUTSIDE BACK EXHAUST
B1.
You need to cut an opening in the rear wall for
outside exhaust.
• Read the instructions on the REAR
WALL TEMPLATE.
• Tape it to the rear wall.
• Cut the opening, following the instructions of the
REAR WALL TEMPLATE.
B2.
OUTSIDE BACK EXHAUST (Horizontal Duct)
B
Blow er Plate
REMOVE BLOWER PLATE
B2. Remove Blower Plate
3/8" TO EDGE
NOTE: IT IS VE
RY IMPORTANT TO
READ AND FOLL
OW THE DIRECTIONS
IN THE INSTALLATION INSTRUCTIONS
BEFORE PROCEEDING WITH THIS
REAR WALL TEMPLATE.
This Rear Wall Template serves to position the bottom
mounting plate and to locate the horizontal exhaust
outlet.
1. Use a level to check that the template is positioned
accurately.
2. Locate and mark at least one stud on the left or
right side of the centerline.
It is important to use at least one wood
screw mounted firmly in a stud to support the weight
of the microwave. Mark two additional, evenly spaced
locations for the supplied toggle bolts.
3. Drill holes in the marked locations. Where there is
a stud, drill a 3/16" hole for wood screws. For holes
that do not line up with a stud, drill 5/8" holes for
toggle bolts.
DO NOT INSTALL THE MOUNTING PLATE
AT THIS TIME.
4. Remove the template from the rear wall.
5. Review the Installation Instruction book for your
installation situation.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTANT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLIN
E.
MARK THE LOCATION FOR
2 ADDITIONAL, EVENLY
SPACED TOGG
LE BOLTS IN THE MOU
NTING PLATE
AREA.
Locate and mark holes to align with holes in the
mounting plate.
IMPORTA
NT:
LOCATE AT LEAST ONE STUD ON EITHER SIDE OF
THE CENTERLINE.
MARK TH
E LOCATION FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE BOLTS IN THE MOUNTING PLATE
AREA.
Trim the rear wall templa
te along the dotted line.
Trim the rear wall template along the dotted line.
12"
4"
Darle vuelta a la ho
ja para consultar la
versión en Español.
Make sure the motor wiring has
3
/8"
TO
EDGE
NO
TE
: IT IS
VERY I
MPO
R
TANT TO
READ AND FOLLO
WT
HED
IRECTIONS
IN THE INSTALLAT
ION INSTRU
CTI
ONS
BE
FORE PROCEEDINGWITH T
HIS
REAR WALL TEMPLA
T
E
.
This Rea
r
Wall Templ
ate
s
e
rves
to p
osition the bo
ttom
mou
ntin
g platea
n
d
to locate the h
o
ri
zon
ta
l ex
hau
st
ou
tlet.
1. Use a levelto
c
heck
th
at the templa
te is p
osition
ed
a
ccur
ate
ly
.
2. Lo
ca
te and
mark at leas
t onestu
d
on the
le
ft o
r
righ
t side o
f the
centerli
n
e.
It is im
po
rtant to u
se
a
t least
one
wood
scre
w mounted fi
r
mly in a stud
to support the weight
o
fthe mic
r
ow
ave.
Mar
k two a
dditional, e
ve
nlyspa
ced
loc
ation
s f
or the s
upplied
to
ggle
bo
lts.
3. Drill holes in
the m
arked lo
cations.Wher
e t
he
re is
a stud, d
r
ill
a 3/16" h
ol
e
for
woo
d s
cr
e
w
s.
For holes
that
d
o n
ot lin
e up
w
ith a s
tud, dr
il
l 5/8
"
holes for
toggl
e bo
lts.
DO
NOT
I
N
S
T
A
L
L THE MOU
NT
I
N
G P
LATE
AT
THIS
TIME.
4. Re
m
ove the templa
te fromthe r
ear wall.
5.R
evie htw e Insta
llationIns
tr
uc
tion book for
your
in
stallatio
n si
tua
t
ion.
Locat
e and m
ar
k
holes
to ali
gn with holes in the
mounting
plate.
IMPO
RTANT
:
LOCATE AT LEAST O
NE
STUD ON EITHER
SIDE OF
TH
E CENTER
LI
N
E.
MARKT
HE LOCATIO
N
FOR 2 ADDITIONAL, EVENLY
SPACED TOGGLE
BO
LTS IN
THE MO
UNTING
PLATE
AREA.
Locate and mar
k holes
to al
ign with holes
in the
.
e
t
alpgnitnuom
IMPO
RTANT
:
LO
CAT
E AT LEAST ONESTUD ON EITHER SIDE O
F
THE
CENTE
R
LINE.
MARKT
HE LOCATIONF
O
R 2 ADDITION
A
L, EVENLY
SPACEDTO
G
GLE BO
LTS IN
THE MOUNTING PLATE
AREA.
Trim the r
ear wall temp
lat
e alongt
he dotted
line.
Trim the rear
wal
l t
em
pla
t
e along
t
h
e dotted line.
12"
4"
Dar
l
evu
elt
aa la ho
j
apar
a
consul
t
a
r
la
v
e
r
s
ióne
nEs
pa
ño
l.
EN-16
Loading ...
Loading ...
Loading ...