Loading ...
Loading ...
Loading ...
WARNING – SERVICING TO BE CARRIED OUT ONLY BY AN AUTHORISED PERSON
Disconnect from electricity and gas supplies before servicing. Check appliance is safe when you have nished.
42
2.5 To Change a Hotplate Burner Thermocouple
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel and hotplate (see 1.2 & 2.1).
Unplug the FSD lead from the rear of the tap.
The thermocouple sits in a hole that has a slot at one side.
Ensure that the thermocouple is cool. Turn the thermocouple
so that the earth lead (no sleeve) is in line with the slot. Lift
the thermocouple clear of the hole.
Reassemble in reverse order.
2.6 To Remove or Change a Hotplate Burner
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the hotplate top (see 2.1). Remove the control panel
(see 1.2).
The burners except the right hand wok burner are mounted
on support struts. For these burners, disconnect the burner
feed pipes at the burner. Remove the screws at the front and
rear holding the support struts. Lift the strut and burners
clear. The burners are xed to the support struts with 2
screws. Remove the appropriate burner and t the new
one. Reassemble in reverse order. Check burner operation is
satisfactory.
Right hand Wok burner
Disconnect the burner feed pipe at the burner. Fit the new
one and reassemble in reverse order. Check burner operation
is satisfactory.
3 Control
3.1 To Change the Ignition Generator
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Change the hotplate tap as detailed in 2.2
3.2 To Replace the Light Switch
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel (see 1.2).
NOTE: The old switch may be destroyed during removal.
Remove the old switch from its bezel by gripping the switch
body behind the control panel and twisting sharply. Remove
the switch bezel by folding back its locking wings and
pushing forward.
Fit the new bezel to the control panel by rst lining up the
raised key on its body with the cut-out in the control panel
and pushing it in from the front.
Assemble the new switch to the bezel by lining up the key
sections and pushing home. Fit the new button by pushing in
from the front.
Replace the control panel in reverse order and test for correct
operation.
3.3 To Remove the Electronic Timer
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Pull o the timer control button(s) and remove the control
panel (see 1.2).
Remove the timer/mounting bracket assembly from the
control panel by removing the xing screws.
Remove the timer from its mounting bracket by depressing
the plastic lugs on the timer case, at the same time pulling
the unit forward.
Reassemble in reverse order. When replacing the leads, refer
to the wiring diagram in this manual. Check the operation of
the timer.
4 Grill
4.1 To Replace the Grill or Ceramic Hob Controller
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove the control panel (see 1.2) and hotplate top (see
2.1). Disconnect the wiring from the controller. Remove the 2
screws holding the controller to the mounting panel.
Fit the new controller and reassemble in reverse order. Check
for correct operation.
4.2 To Remove the Grill Element
DISCONNECT FROM THE ELECTRICITY SUPPLY.
Remove grill pan from inside the grill compartment; remove
the enamelled front shield from the grill roof, by removing
the 2 screws and washers.
Remove the 2 screws and washers securing the grill element
front support. Remove the screws from the grill element.
Lift the element out carefully, disconnecting the leads from
the element terminals (noting their position).
If it is not possible to disconnect the leads in this way, pull the
cooker forward to gain access to the rear, remove the screws
securing the electric cover to the back sheet, remove the
cover and disconnect the terminals from the rear.
Fit the new element and reassemble in reverse order. Check
the operation of the grill.
Loading ...
Loading ...
Loading ...