Loading ...
Loading ...
Loading ...
12
© 2021 United States Stove Company
The heater will begin to feed fuel and the exhaust
(draft) blower is running. Note that the exhaust
blower is pulsing. The auto-start ignitor will ignite
the fuel in approximately 5-10 minutes. In the start-
up mode, the “ON” LED will ash until it reaches a
factory preset temperature. At that point, the “ON”
LED will come on solid and the heater will begin to
ramp up to your selected heat range. The Room Air
Blower will not function until the heater reaches a
factory preset temperature. Attempts to achieve
heat output rates that exceed heater design
specications can result in permanent damage to
the heater.
SHUT DOWN PROCEDURE
WARNING:
NEVER SHUT DOWN THIS UNIT BY UNPLUGGING
IT FROM THE POWER SOURCE.
Press the “OFF” button on the control pad to put
the stove in shut down mode. At this time, the red
light above the OFF will blink and the “ON” light will
go off. The auger will stop feeding pellets, but the
distribution blower and exhaust blower will continue
to operate. When the internal temperature of the
unit drops below the factory preset temperature,
the distribution blower and exhaust blower will
cease to operate. The red light will then shut off
and the unit will be completely shut down. The
hotter the unit is during its operation, the longer it
will take for the stove to complete the shut down
cycle. If the stove stays on for more than 1 hour after
pressing the “OFF” button and you are sure that
the re is out, the stove can be unplugged from
the outlet. After approximately 10 seconds, the unit
can be re-connected to the power source and the
control board will be reset.
DAILY OPERATION
• Never place your hand near the auger while the
heater is in operation.
• This unit should be lled when the hopper level
drops below 3-inches.
• In the event of a power outage, the heater will
not function. If the unit was “ON” when the power
outage occurred, one of the following will take
place:
1. If the heater is still warm, it will resume feeding
fuel and continue to operate normally. If the re
has gone out, you will have to press the “OFF”
button and then the “ON” button again to begin
a new start-up sequence.
2. If the heater has cooled-off, it will reset to its
“OFF” condition. At this point, you may press
the “ON” button and the unit will begin a new
start-up sequence. Make it a habit to empty the
burn pot in these situations.
NOTE: The unit will also shut down in the event of an
exhaust blower failure; if this is the case, the unit will
not re-start and you must contact Customer Service.
The amount of visible smoke being produced can be
an effective method of determining how efciently
the combustion process is taking place at the given
settings. Visible smoke consist of unburned fuel
and moisture leaving your stove. Learn to adjust
the air settings of your specic unit to produce the
smallest amount of visible smoke. Wood that has
not been seasoned properly and has a high wood
moisture content will produce excess visible smoke
and burn poorly.
SAFETY AND CONVENIENCE FEATURES
Your heater incorporates safety switches that helps
ensure that everything is in proper working order
before feeding fuel to the burn pot. The heater will
not operate if the viewing or combustion door is left
open; or if the exhaust blower fails or the exhaust
system is blocked. The RTD, Resistance Temperature
Device, will prevent your heater from operating at
abnormally high temperatures. The heater has two
over temperature limits. If the unit reaches the rst
limit, it will reduce fuel consumption in order to
reduce temperatures. If the unit reaches the second
limit, it will shut down and will need to be restarted.
Your heater also includes an auto-start igniter as
a standard feature. The use of other re starter
materials (wood chips, starter gel, etc.) is not
necessary. By simply pressing the “ON” button on
the digital control panel, your heater will begin to
feed fuel and automatically start within 5 minutes.
This wood heater has a manufacturer-set minimum
burn rate that must not be altered. It is against
federal regulations to alter this setting or otherwise
operate this wood heater in a manner inconsistent
with operating instructions in this manual.
OPERATION INSTRUCTIONS
Loading ...
Loading ...
Loading ...