Loading ...
Loading ...
Loading ...
iiii iiii i i ....
TROUBLE SHOOTING POINTS
iii el i iii = H =H== = H =I=====H== =n,== ........
TROUBLE SHOOTING CHART
SYMPTOM CORRECTION
Engine willnot start or
wil!run only for a
few seconds after
starting.
,,j ,
1. Fuel tank empty.
2. Engine flooded.
3. Spark plug not firing,
4. Fuel not reaching carburetor.
5. Carburetor requires adjustment.
6. None of the above.
Engine willnot
idle properly.
1. Carburetor set too fasi or too slow.
2. Carburetor requires adjustment.
3. None of the above.
Engine wili not 1. Air filter dirty.
accelerate, lacks 2. Spark plug fouled.
power,or dies
under a load. 3. Carburetor requires adjustment.
4. Muffler outlets plugged.
5. None of the above.
Engine !. Airfilter dirty.
Smokes 2. Fuel mixture incorrect.
excessively, 3. Carburetor requiresadjustment.
Engine
runs hot
Cutting head
stopsunder a load
or does not turn when
engine is accelerated,
_L
1. Fuel mixtureincorrect.
2. Spark plug incorrect.
3. Carburetorset too high (lean).
4. WrongdiametercuttingIine.(too large)
5. None ofthe above.
Line doesnot
advance or breaks
whilecutting.
Line weldsonto
spool.
Line purlsback
into head.
'i. Driveshaftnot engaged.
2. Driveshaftbroken,
1. Line improperiY';outedin head.
2. Line improperly wound onto spool.
3. Line size incorrect,
4. Old cuttingline.
5, Too littleline outside head.
6. Dirt accumulated in cover.
7. Line woundin wrong direction.
,,, ,.,,, ,,
1. Line size incorrect.
2. Old cuttingline.
3. Incorrect spool.
4. Crowding line against material
being cut.
,,ml i ,, i, i,,,,,,,i i,i ii, i
1 Too litUeline outside of head.
2. Old cuttingline.
1. Filltankwith correctfuel mixture.
2. See "Starting Instructions".
3. InstalJnew plug/check ignitionswitch.
4. Reptace fuel filter; inspectfuel line.
5. See "Carburetor Adjustments."
6. Contact your SEARS Service Center/Dept.
1.See "Carburetor Adjustments."
2. See "Carburetor Adjustments."
3. Contact your SEARS Service Center/Dept.
1. Clean or replace air filter.
2. Clean or replace spark ptug and re-gap.
3. See "Carburetor Adjustments."
4. Contact your SEARS Service Center/Dept,
i 5. Contact your SEARS Service Center/Dept,
1.Clean or replace air filter.
2. Refuel with correct fuel mixture.
3. See "Carburetor Adjustments."
1, See' "Fueling'"-Your Unit."
2. Replace with correct plug.
3. See Carburetor Adjustments."
4. Use only .080 "diameter cutting line.
_.Contact your SEARS Service Center/Dept.
1. See "Assembly," "Tube", insert fully.
2. Contact your SEARS Service Center/Dept.
t. Remove cover. Check linerouting.-_--
2. rewindline tightlyand evenly.
3. Useonly.080" diameter line,
4. Replace with new cutting line.
5. Remove cover. Pull4" of lineto outside.
6, Clean cover.
7. Rewindin correctdirection.
1, Use only.080" diameter line,
2. Replace with new cutting line.
3. Use properspool.
4. Cut withtip of line.
5. Reduce cuttingspeed.
,, ,,,, i i
1. Remove cover. Pull 4" of line to outside.
2. Replace with new cuttingline.
If situationsoccurwhichare not covered in this manua usecare and good judgemenL
Ifyou need assistance, contact your SEARS ServiceCenter/Department or the
CUSTOMER ASSISTANCE HO TLINE AT 1-800-235-5878.
- 31 -
Loading ...
Loading ...
Loading ...