Loading ...
Loading ...
Loading ...
If your saw
that looks like below.
is for use on less than 150 volts it has a plug
3-PRONG PLUG
GROUNDING PRONG
_ PROPERLY GROUND'ED
3-PRONG OUTLET
Plug power cord into 110-120V properly grounded type
outlet protected by a 15-amp. time delay or Circuit-Saver
fuse or circuit breaker.
IF YOU ARE NOT SURE THAT YOUR OUTLET IS
PROPERLY GROUNDED, HAVE IT CHECKED BY A
QUALI FI ED ELECTRICIAN.
WARNING: DO NOT PERMIT FINGERS TO TOUCH
THE TERMINALS OF PLUG WHEN INSTALLING OR
REMOVING THE PLUG TO OR FROM THE OUTLET.
WARNING: IF NOT PROPERLY GROUNDED THIS
POWER TOOL CAN INCUR THE POTENTIAL HAZARD
OF ELECTRICAL SHOCK, PARTICULARLY WHEN
USED IN DAMP LOCATIONS; IN PROXIMITY TO
PLUMBING, OR OUT OF DOORS. IF AN ELECTRICAL
SHOCK OCCURS THERE IS THE POTENTIAL OF A
SECONDARY HAZARD SUCH AS YOUR HANDS
CONTACTING THE SAWBLADE.
This saw is equipped with a 3-conductor cord and
grounding type plug which hasagrounding prong, approved
by Underwriters' Laboratories and the Canadian Standards
Association. The ground conductor has a green lug and is
attached to the tool housing at one end and to the ground
prong in the attachment plug at the other end.
This plug requires a mating 3-conductor grounded type
outlet as shown.
If the outlet you are planning to use for this saw is of the
two prong type DO NOT REMOVE OR ALTER THE
GROUNDING PRONG IN ANY MANNER. Use an adapter
as shown and always connect the grounding lug to a known
ground.
It is recommended that you have a qualified electrician
replace the TWO prong outlet with a properly grounded
THREE prong outlet.
An adapter as shown below is available for connecting plugs
to 2-prong receptacles. The green grounding lug ex_ending
from the adapter must be connected to a permanent ground
such as to a properly grounded outlet box.
GROUNDING LUG
ADAPTER / _ -
/ I1_I MAKESURET_I[S1S
3-PRONG \ _ ! _'_,._---- CONNECTED I'C A
PLUG _[_ I "_ I KNOWN GROLIND
\ ,,_'%-__1 I I I
,_ _- '_ RECEPT _,CLE
NOTE: The adapter illustrated is for use only if you already
have a properly grounded 2-prong receptacle.
The use of any extension cord will cause some loss of
power. To keep this to a minimum and to prevent
over-heating and motor burn-out, use the table below to
determine the minimum wire size (A.W.G.) extension cord.
Use only 3 wire extension cords which have 3 prong
grounding type plugs and 3-pole receptacles which will
accept the plug on the saw.
Extension Cord Length Wire Size A.W.G.
Upto 100 Ft ...................... 12
100 - 200 Ft ....................... 10
200 - 400 Ft ........................ 8
CO NTE NTS
WARRANTY ....................................... 2
GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS .............................. 2
ADDITIONAL SAFETY INSTRUCTIONS
FOR TABLE SAWS ................................ 3
MOTOR SPECIFICATIONS AND ELECTRICAL
REQUIREMENTS .................................. 4
UNPACKING AND CHECKING CONTENTS ........... 6
Tools Needed ..................................... 6
List of Loose Parts ................................ 6
ASSEMBLY ....................................... 7
Installing Elevation and Tilt Handwheels ............ 7
Checking Table Insert ............................. 7
Checking Blade Squareness to Table ............... 8
Checking Blade Elevation .......................... 8
Attaching Table Extensions ........................ 8
Installing Rip Fence Guide Bars .................... 9
Assembling Steel Legs .......................... 1O
Mounting Saw ................................. 10
Aligning Table Extensions ....................... 11
Aligning Rip Fence .............................. 11
Installing Blade Guard .......................... 13
GETTING TO KNOW YOUR SAW .................. 15
On-Off Switch .................................. 15
Reset Button ................................... 16
Elevation Handwheel ............................ 16
Tilt Handwheel ................................. 16
Rip Fence ...................................... 16
Miter Gauge .................................... 16
Blade Guard .................................... 16
Table Insert .................................... 16
Removing and Installing Sawblade ............... 17
BASIC SAW OPERATION USING THE MITER GUAGE 17
Work Helpers ................................... 17
Crosscutting .................................... 18
Repetitive Cutting ............................... 19
Miter Cutting ................................... 20
Bevel Crosscutting .............................. 20
Compound Miter Cutting ........................ 20
BASIC SAW OPERATION USING THE RIP FENCE .. 20
Ripping ........................................ 21
Bevel Ripping .................................. 21
Resawing ...................................... 22
Cutting Panels .................................. 22
Ploughing and Molding .......................... 22
Rabbeting ...................................... 23
Dadoing ........................................ 23
Using Featherboards ............................ 23
ADJUSTMENTS ................................. 24
Miter Gauge .................................... 24
Heeling Adjustment or Parallelism of
Sawblade to Miter Gauge Groove ............... 24
Blade Tilt, or Squareness of
Blade to Table ................................. 25
Blade Elevation ................................. 26
Tilt and Elevation Mechanism .................... 26
MAINTENANCE .................................. 27
LUBRICATION ................................... 27
RECOMMENDED ACCESSORIES .................. 27
TROUBLESHOOTING ............................. 28
REPAIR PARTS .................................. 30
Loading ...
Loading ...
Loading ...