Loading ...
Loading ...
Loading ...
kickback.
* Whilecuttinglog,neverholdlogwith
yourhandorleg.
* Whilecuttinglog,neverallowanother
persontoholdlog.
* Turnoffandunplugsawbeforemoving
fromoneplacetoanother.
ASSEMBLING TIlE
EXTENSION PQLE (QNL¥
FQR MODEL WG3QS)
_ ARN|NG: Before attaching the
e_e"sEon po|e (20), make sure that
the too| is switched off a"d u"p|ugged.
1. Turn the release lever to allow the handle
clamp to spring open (See Fig. Z1).
2. With the pole slightly angled away from
the tool, insert the steel tab into the slot
behind the front handle, then swing the
pole towards the tool's rear handle. (See
Fig Z2).
3. Position the pole handle clamp inside the
JawSaw's rear handle as shown in Fig
Z3.To allow the clamp to properly fit the
handle, push lock out button and depress
the trigger.
4. Close the clamp, the locking lever will
automatically lock into place.
5. Check that the rear handle is properly
fitted to the clamp and check that the
clamp is properly set in the lock position.
6. Plug in the tools power cord to the
extension pole power cord (_). (See Fig.
Z4)
_ WARN|NO. w Before attachi"g the
power cord of the machi"e to the
power cord of the exte"sio" po|e ((_)
i" Fig. Z4), make sure that the too| is
switched off a"d u"piugged fro,. the
power supply.
_ ARN|NO." Whe" using this
machi"e with the exte"sio" pole,
make sure that a_achi"fj the power
cord of the machi"e to the power cord
of the exte"sio" pole, a"d the" attach
the power cord of the exte"sio" pole to
power supply.
_ ARNiNG". ELECTROCUTION
HAZARD
Never use the JawSaw or extension pole in
an area with overhead power lines or where
the branch being cut can come into contact
with overhead power lines.
CUTTING WITH EXTENSION POLE (ONLY
FOR WG3B8)
1. Attached the pole as described in
"Assembling the extension pole".
2. Connect the JawSaw to extension cord.
Connect extension cord to power supply.
NOTE: The JawSaw is quite heavy on the
end of the extension pole.
Add the pole attachment when cutting
limbs above shoulder height and remove
the pole saw when cutting limbs at or
below shoulder height.
3. Lift JawSaw with extension pole upward
one step by one step (See Fig. AA). To
raise to the vertical position, lift by the
Jawsaw first, then hand over hand along
the pole.
4. Before cutting a high branch, consider all
the same points detailed in the previous
section "Trimming Branches" but pay
particular attention to the likely path of the
falling branch.
WARN|NG: Do "ot sta"d direct|y
be|ow a bra"ch bei"g cut. Keep
bysta"ders far away. |)o "or sta"d o" a
|adder or other type of e"stabie suppo_
while usi"g the tool |)o "or use the too|
,,ear ca|)ie, e|ectrica| power or teiepho"e
|i"es. Keep I Oft (3,.) away from ai|
power |i"es. (See Fig. AS14&B4|)
5. Position the Jaw perpendicularly on the
branch being cut.
NOTE: Maximum eetti"g capacity of
JawBaw is 4 i"ches (10cm).
6. One hand should firmly grip the push
handle of the extension pole.The other
hand should hold the metal portion ofthe
pole or the sliding handle on the pole (See
Fig. AC).
7. Complete the cut as described in
"Trimming Branches"
8. At the completion of the cut, be ready to
immediately support the weight of the
Loading ...
Loading ...
Loading ...