Loading ...
Loading ...
Loading ...
12
© 2021 United States Stove Company
OPERATION INSTRUCTIONS
PRESTARTUP CHECK
Remove burn pot, making sure it is clean and none of the
air holes are plugged. Clean the firebox, and then reinstall
burn pot. Clean door glass if necessary (a dry cloth or
paper towel is usually sucient). Never use abrasive
cleaners on the glass or door. Choose which fuel setting
that you wish to operate in. Do this by first pressing
the “ON” button, then press the “Heat Range” Up and
Down arrows together for approximately 3-4 seconds
and release. A “C” or “P” in the first digit of the display
will indicate the mode. The “ON” led will be blinking and
the display will show “CR-1” or “PR-1”, depending on the
mode. The “Heat Range” indicator LED and the “Auto”
LED should be lit and the dash in the Heat Range display
should be flashing. You will notice the draft fan starts
immediately. If you press the “Heat Setting” button up, the
draft fan changes speed, increasing speed the higher the
heat setting. You should begin to see the igniter, located
in the center and behind the burnpot, begin to glow after
a short period of time. In CR-1, the auger and agitator will
start rotating after a few minutes, allowing for proper fuel
ignition. In PR-1, the auger will turn immediately, then
the agitator will begin to rotate once the heater reaches
operating temperature. Note: The room fan will not
operate at this time, as a temperature of at least 110°F
must be reached before operating. If proper operation of
your heater is confirmed, press the “OFF” button, then fill
your hopper with fuel. Ensure there is no foreign matter in
your fuel, hopper or burnpot.
BUILDING A FIRE
Never use a grate or other means of supporting the fuel.
Use only the burn pot supplied with this heater. Hopper
lid must be closed in order for the unit to feed pellets.
During the start-up period:
• Make sure the burn pot is free of pellets.
• DO NOT open the viewing door.
• DO NOT add pellets to the burn pot by hand.
NOTE: During the first few fires, your stove will emit an
odor as the high-temperature paint cures or becomes
seasoned to the metal. Maintaining smaller fires will
minimize this. Avoid placing items on the stovetop during
this period because the paint could be aected. Attempts
to achieve heat output rates that exceed heater design
specifications can result in permanent damage to the
heater.
IGNITOR
• Close all doors, lids, and cleanouts.
• Press the “ON” button and select desired heat range.
This will start the ignition sequence.
• At this point, the igniter will come on and run for preset
time limit (approximately 9 minutes). The auger will
begin to turn and feed fuel into the burnpot. After the 9
minutes or if the heater reaches operating temperature,
the igniter will shut o and normal operation will begin.
• Make fine adjustments to the air/fuel with the damper
located centered, under the hearth.
• Once the heater reaches warm temperature, the room
fan will start to circulate air into the room.
• If you would like to increase the life of your ignitor, you
can run your heater in the “CR” mode. However, you
must place pellets in the burnpot, up to the igniter level
as shown in the illustration below for auto ignition.
Close the door and press the “ON” button. The igniter
only runs approximately half the time in “CR” as oppose
to the “PR” mode.
OPENING DOOR
CAUTION:
• DO NOT OPERATE YOUR STOVE WITH THE
VIEWING DOOR OPEN. THE AUGER WILL NOT
FEED PELLETS UNDER THESE CIRCUMSTANCES
AND A SAFETY CONCERN MAY ARISE FROM
SPARKS OR FUMES ENTERING THE ROOM.
• THE DOOR MUST BE CLOSED AND SEALED
DURING OPERATION.
If the door is opened while the stove is in operation it
must be closed within 30 seconds or the stove will shut
down. If the stove shuts down push the “On/O” button
to re-start your stove. The stove will have to fully shut
down and turn o before you will be able to restart the
stove.
TAMPER WARNING
This wood heater has a manufacturer-set minimum low
burn rate that must not be altered. It is against federal
regulations to alter this setting or otherwise operate this
wood heater in a manner inconsistent with operating
instructions in this manual.
Loading ...
Loading ...
Loading ...