Laser Dart Line Mounting Instructions #37-0108
AVOID EXPOSURE LASER RADIATION IS EMITTED FROM THE APERTURE
AVOID DIRECT EYE EXPOSURE
Max Output <5mW, Wavelength 650nm-660mm, Class II Laser Product
Complies with FDA Radiation Performance Standards 21 CFR Chapter 1, Subchapter J
GLD Products, Muskego, WI 53150, Model #37-0108
ACCESSION NO:1410047-000
When the laser beam dims, or stops operating, replace batteries
Dispose of batteries promptly and properly, Do not burn them
Use only fresh batteries of the required size and type
Do not mix old and new batteries, or different types
If you do not plan to use the Laser Dart Line for a month or more remove batteries,
batteries can leak chemicals that can damage electronic parts
WARNING! Never look directly into the laser
WARNING! Keep away from children
WARNING! Never point the device towards anyone’s eyes
WARNING! Laser light can also be dangerous when reflected on a mirror-like surface
WARNING! Use of controls or adjustments, or the performance of procedures other than specified herein,
can result in hazardous radiation exposure
Read all instructions carefully before mounting the Laser Dart Line.
The Laser Dart Line can be mounted directly to a wall or the underside of a dartboard cabinet.
Required tools: pencil, screws, screwdriver, tape measure, drill, drill bit, and level.
Instructions
1) Mount your dartboard or dart cabinet. With one hand place the Laser Dart Line on the wall or cabinet
directly below and centered to the dartboard. With your other hand level the Laser Dart Line.
2) Locate the two mounting holes on the front of the Laser Dart Line. Use a pencil, marker, or nail to mark the
center of the holes on the wall or cabinet.
3) Drill a pilot hole on each mark that you created in step two. If using plastic anchors for dry wall, plaster, or
cement drill the holes so that the anchors fit snugly. Insert the plastic anchor. If drilling into a wood cabinet
or wood stud, only pilot holes will be necessary.
4) Align the Laser Dart Line with the anchors or pilot holes and screw the Laser Dart Line into place. The
screws will expand the plastic anchors. Before tightening the screws, check that the Laser Dart Line is level.
5) Remove the front battery cover and insert 4 AA batteries. The Laser Dart Line can also be powered by an
AC to 5v adapter with DC plug polarity configured as positive (+) outside and negative (-) inside. (4 AA
Batteries and adapter not included)
DANGER
Backboard
Dartboard
Laser Dart Line
Level
Cabinet
Dartboard
Laser Dart Line
Level
Cabinet
Door
Laser Dart Line
Side View
Mounting Holes
Close Up
Make sure your mark
is centered in the oval
OFF ON
6) Measure the distance for your throw line
7) Once your laser throw line is set, tighten the 2 screws next to ball to secure the Laser Line in place.
8) WARNING: AVOID DIRECT EYE EXPOSURE
Turn the Laser Dart Line on and position the laser head until it is flush with your temporary line.
9) If your surface area is uneven, loosen either the left or right screw and place shims behind the housing of
the Laser Dart Line until the Laser Dart Line is in the correct position.
The laser line should be 96" from the face of the dartboard
Soft Tip
Dartboard
Wall
The laser line should be 93¹/4" from the face of the dartboard
Steel Tip
Dartboard
Wall
Temporary line
Measure
96" or 93¼"
Measure
96" or 93¼"
Adjust the angle of the laser head
so that the line appears the correct
distance from the wall
Temporary line
Laser Dart Line
Muskego, WI 53150
www.gldproducts.com
by GLD PRODUCTS
LASER DART LINE Item #37-0108 Power Adapter Order Form
Mail To:
GLD Products
S84 W19093 Enterprise Drive
Muskego, WI 53150
Email: [email protected]
www.gldproducts.com
Name
Address
City
State Zip
Date
Phone-Day
Phone-Evening
Email
Order# Description Unit Price QTY Amount
#42-9988 5v 500ma Positive Outer Adapter
$10.00
Subtotal
Shipping will be added. If paid by check or money
order, call for quote
S/H
5.1% Waukesha, WI tax will apply (Subject to
Change)
TAX
Total
Shipping Address
Name________________________________________________________________
Address_______________________________________________Phone__________
City___________________________________________State________Zip________
Method of Payment
____Check or Money Order
____Credit Card
__Visa __Mastercard __Discover __American Express
Card#___________________________________
Security Code #_____________Billing Address Zip Code__________
Signature_______________________________ Exp. Date _________
Use a common household
item, such as a broom handle
or ruler, to make a temporary
line at the correct distance.
Measure from each side of the
dartboard to the temporary line.
