Loading ...
Loading ...
additionaJ safety instructions for scroll saw
Safety isacombination ofoperator common sense and altert-
ness at all times when the scroll saw is being used,
WARNING: FOR YOUR OWN SAFETY, DO NOT ATTEMPT
TO OPERATE YOUR SCROLL St_' UNTIL IT IS COMPLETELY
ASSEMBLED AND iNSTALLED ACCORDING TO THE
INSTRUCTIONS...AND UNTIL YOU READ AND UNDER.
STAND THE FOLLOWING:
Page
1. General Safety Instructions for Power Tools ...... 2
2. Assembly .................................. 6
3. Getting To Know Your Scroll Saw .............. 12
4. Basic Scroll Saw Operation ................... 14
5. Maintenance ............................... 16
6. Stability of Machine.
Your scroll saw must be bolted securely to stand or work
bench, In addition, if there isany tendencyfor the scroll saw
tomove during certain operations,bolt yourscrollsaw stand
or workbench to the floor.
7. Location
This scrollsaw is intended for indoor use only.
8. Protection: Eyes, Hands, Face, Ears, Body
A. To avoid being pulled intothe blade:
1. Roll long sleeves above elbows
2. Do not wear:
a. Gloves
b. Jewelry
c. Ties or other loose clothing
3. Tie back long hair
B. Do not cut pieces ofmaterial toosmall to hold by hand
outside the blade guard.
C. Avoid awkward hand positions where a sudden slip
could cause a hand to move intothe blade.
D. Toavoid slips due tolifting of the workpiece make sure
the blade teeth point downward toward the table.
E. To avoid blade breakage always adjust blade tension
correctly.
F. To avoid losing control of the work piece or tool:
1. When cutting a large piece of material make sure it
is fully supported at table height.
2. Hold the work piece firmly against the table.
3. Do notfeed the material too fast while cutting. Only
feed the material fast enough so that the blade will
cut.
4. Use caution when cutting off material which is
irregular incross section which could pinch the blade
before the cut is completed. A piece of moiding, for
example, must ray flat on the table and not be per-
mitted to rock while being cut.
5. Use caution when cutting off round material such as
dowel rods, or tubing. They have a tendency to roll
while being cut causing the blade to bite. Use a V-
block to control the piece.
G. When backing the blade out ofthe workpiece, the blade
may bind in the kerf (cut).,.this is usually caused by
sawdust clogging up the kerf. If this happens: Turn off
the scroll saw.. .remove plug from power source
outlet...wedge open the kerr.., back the blade out ofthe
workpiece.
H. To avoid unsupervised work, use or accidents due to
inattention:
t. Never leave the scroll saw workarea with the power
on, before the machine has come to a complete stop,
or without removing and storing the switch key.
2. Do not perform layout, assembly or set up work on
the table while the cutting tool is in operation.
3. Turn saw "OFF" and remove plug from power supply
outlet before installing or removing an accessory
attachment.
4. Never turn your scrolt saw "ON" before clearing the
table ofall objects: (tools, scraps of wood, etc.) except
for the work piece and related feed or support
devices for the operation planned.
9. Should any part of this scroll saw be missing, bent, or fail
in any way, or any electrical component fail to perform
properly, shut off power switch and remove plug from power
supply outlet. Replace damaged, missing, and/or failed
parts before resuming operation.
10.Think Safety.
Safety is a combination of operator common sense and
alertness whenever the scroll saw is in operation.
WEAR YOUR
The operation of any power tool can resuit in foreign objects
being thrown into the eyes, which can result in severe eye
damage. Always wear safety goggles complying with ANSI
Z87.1 (shown on Package) before commencing power tool
operation. Safety goggles are available at Sears retail or
catalog stores.
i DANGER ! _o,You_ownSAF_'_-__._ o._.
manu_bek_'eoparat_j Sc_t Saw.
t. ALWAYS wear SAFETY GOGGLES complying with ANSi 7.87.!.
3.Turn saw Off and REMOVE SW]TCH KEY before ad_ saw, ch_ blade, or
_vingarea.
4.When INSTALLING BLADE: Blade teeth must a_ays point down. Puttension onblade
I_ turr_ kno_ (at rear) dook_se or_ _1t _,_rnI_ t_,e,up of _, F_ _
installal_ az_ ct'_YJng: procedure inowner's manual. _\
Eiect_al: 120voWs
60 HZ AC 0_ty, 2,0 amps es,_4_=
I
J
WARNING: ALWAYSKEEP ALERT. DO NOT ALLOW FAMILIARITY (GAINED FROM FREQUENT USE OF YOUR SCROLL SAW)
TO CAUSE A CARELESS MISTAKE. ALWAYS REMEMBER THAT A CARELESS FRACTION OF A SECOND IS SUFFICIENT
TO iNFLICT SEVERE INJURY.
Loading ...
Loading ...
Loading ...