Loading ...
_ : ,::_ :::/, . - ) : : :: : :, .
SCROLL SAW
.=to a defect in material or
--I'SMAN SCROLL SAWTO THE NEAREST
tNTHE UNITED STATES.
also have other rights which varyfrom state to
Seam Tower; BSC 41-3, Chicago, fill®is 60884
general safety instructions for power teems
1. KNOW YOUR POWER TOOL
Read and understand the owner's manual and labels
affixed to the toot. Learn its application and limitationsas
well as the specific potential hazards pecutiar tothistool.
2. GROUND ALL TOOLS
This toolis equipped with an approved 3-conductor cord
and a 3_prong grounding type plug to fit the proper
groundir_g type receptacle. The green conductor in the
cord is the grounding wire. Never connect the green wire
to a live terminal.
3; KEEPGUARDS IN PLACE
--in working order, and place adjustment and alignment.
4. REMOVE ADJUSTING KEYS AND WRENCHES
Form'a habit of checking to seethat keys and adjusting
wrenches are removed from tool before turning it on.
5, KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents. Floor must
notbe slippery due towax or sawdust.
6,: AVOID DANGEROUS ENVIRONMENT
7. KEEP CHILDREN AWAY ..... =
All Visitorsshoutd be kept a safedistance from workarea;
8. MAKE WORKSHOP CHILD PROOF : :
with padlocks, master switches, or by removingstarter
keys.
9. DON'T FORCE TOOL
It will do the job better and safer at the rate fo{"which it
was designed.
USE RIGHT TOOL
Don't force tool or attachment to do a job it was not
designed for.
WEAR PROPER APPAREL
Do not wear loose clothing, gloves, neckties or jewelry
(rings, wristwatches) to get caught in moving parts.
NONSLIP footwear is recommended. Wear protective
hair covering to contain long hair.RGII longsleeves above
the elbow.
10.
!1.
12; USE SAFETY GOGGLES (Head Protection)
Wear safety goggles (must comply with ANSI Z87.1)at all
times; ,Everyday eyeglasses only have impact resistant
lens. the/are NOT safety glasses." Also, use face or dust
mask if cutting operation is dusty, and ear protectors
(plugs or muffs) during extended periods of operation.
13. SECURE WORK
Use clamps or a vise to hold work when practical. It's
safer than using your hands and frees both hands to
operate tool,
14, DON'T OVERREACH
Keep proper footing and balance at all times,
15. MAINTAI N TOOLS WITH CARE
Keep tools sharp and clean for best and safest perfor-
mance. Follow instructions for lubricating and changing
accessories.
16.
17.
18.
DISCONNECT TOOLS
before servicing; when changing accessories such as
blades, bits, cutters, etc.
AVOID ACCIDENTAL STARTING
Make sure switch is in "OFF" position before plugging
in power cord.
USE RECOMMENDED ACCESSORIES
Consult the owner's manual for recommended acces-
sories. Followthe instructionsthataccompany the acces-
sones. The use of improper accessories may cause
hazards.
19_ NEVER STAND ON TOOL
Serious injury could occur if the tool is tipped or if the
cutting tool isaccidentally contacted.
Do not store materials above or near the tool such that
it isnecessary to stand on the tool to reach them.
20. CHECK DAMAGED PARTS
Before further use ofthe tool, a guard or other part that
is damaged should be carefully checked to ensure that
it will operate properly and perform its intended function.
Check for alignment of moving parts, binding of moving
parts, breakage of parts, mounting, and any other con-
ditions that may affect its operation. A guard or other part
that is damaged should be properly repaired or replaced.
21. DIRECTION OF FEED
Feed work into a blade or cutter against the direction of
rotation of the blade or cutter only,
22. NEVER LEAVE TOOL RUNNING UNATTENDED
Turn power off Don't leave tool until it comes to a
complete stop,
2
Loading ...
Loading ...
Loading ...