Loading ...
Loading ...
Loading ...
en Cleaning function
28
5. Swipe to the left or right to select "EasyClean š".
6. Touch the bottom line.
7. Touch the # touch button.
The appliance starts EasyClean. The remaining time
appears on the display.
Finishing
As soon as the cleaning aid has finished, an audible
signal sounds and the appliance ends the operation
automatically.
As soon as you open the appliance door, the interior
lighting is switched on so that you can finish cleaning
the cooking compartment more easily. The remaining
water in the cooking compartment must be removed
promptly. Do not leave the remaining water in the
cooking compartment for a long time (e.g. overnight).
The appliance must not be operated when the cooking
compartment is still wet or damp.
Subsequent cleaning
1. Open the appliance door and remove the remaining
water with an absorbent sponge cloth.
2. Clean the smooth surfaces in the cooking
compartment with a dish cloth or a soft brush.
Stubborn residues can be removed using a stainless
steel scouring pad.
3. Remove limescale with a cloth soaked in vinegar.
Then wipe with clean water and rub dry with a soft
cloth (including under the door seal).
4. Use the # touch button to switch off the appliance.
5. Leave the appliance door ajar in the stop position
(approx. 30°) for approx. 1 hour to allow the enamel
surfaces in the cooking compartment to dry
thoroughly.
Removing heavy deposits of dirt
You have several options for removing particularly
stubborn deposits of dirt.
■ Leave the soapy water to work for some time before
starting the cleaning aid.
■ Rub soapy water onto the dirt on the smooth
surfaces before starting the cleaning aid.
■ Repeat the cleaning aid once the cooking
compartment has cooled down.
Descaling
The appliance must be descaled regularly in order for it
to continue operating correctly.
There are several steps in the descaling programme.
For hygiene reasons, the descaling programme must
be run through completely so that the appliance can be
ready for operation again.In total, the descaling
programme runs for approx. 70-90 minutes.
■ Descale (approx. 55-70 minutes), then empty and
refill the water tank
■ First rinsing cycle (approx. 6-9 minutes), then empty
and refill the water tank
■ Second rinsing cycle (approx. 6-9 minutes), then
empty and dry the water tank
If the descaling process is interrupted (for example, due
to a power failure or because the appliance has been
switched off), you are prompted to rinse the appliance
twice after it is switched back on. The appliance cannot
be used until the second rinsing cycle has come to an
end.
The frequency with which the appliance must be
descaled depends on the hardness of the water used.
When only five more steam-assisted operations are
possible, or fewer, the appliance reminds you to
descale it with a message on the display. The number
of remaining operations is displayed after the appliance
is switched on. You can therefore prepare for the
descaling in good time.
Start
Caution!
■ Damage to the appliance: Use only liquid descalers
that are recommended by us for the descaling
programme. The time the product needs to work
during descaling depends on the type of descaler
used. Other descalers may damage the appliance.
Descaler order no. 311 680
■ Descaling solution: Do not allow any descaling
solution or descaler to come into contact with the
control panel or other delicate surfaces. This will
damage the surfaces. If this does happen, remove
the descaling solution immediately with water.
If you have used a steam-assisted operation
immediately before descaling, you must first switch the
appliance off so that the residual water is pumped out
of the evaporator system.
1. Mix 400 ml water with 200 ml liquid descaler to
make a descaling solution.
2. Touch the # touch button.
3. Remove the water tank and fill with descaling
solution.
4. Fully insert the water tank filled with the descaling
solution.
5. Close the control panel.
6. Touch the 0 touch button.
7. Swipe to the left or right to select "Descale ,".
8. Touch the bottom line.
The duration of the descaling programme is
displayed. It cannot be changed.
9. Touch the bottom line.
10. Touch the # touch button.
The appliance is descaled. The remaining time
counts down on the display. As soon as the
descaling programme has finished, an audible
signal sounds.
First wash cycle
1. Open the control panel.
2. Remove the water tank, rinse thoroughly, fill with
water and reinsert.
3. Close the control panel.
4. Touch the # touch button.
The appliance is rinsed. As soon as the wash cycle
has finished, an audible signal sounds.
Loading ...
Loading ...
Loading ...