Loading ...
Loading ...
Loading ...
A light filmofoi! shouldbewipedonthefaceof the
columntubeto lubricatethefit betweenthecolumn
tubeandcolumnsupport.Withelevationcrankraise
armto upperlimit Completelycollapsebellowsby
pullingdownon top flangeas illustratedfor-access
to columntube.
Thethreadon theelevationshaftassemblycan be
lubricatedthroughthe oil holein the centerof the
radialarmcap Lubricaterampon theswivelindex
spring.
CAUTION:Excessive oil at any location will attract
airborne dust particles and sawdust.
recommended accessories
ITEM CAT,, NO,,
Sawblades (!0" diameter with
with 5/8" hole) ................................ See Catalog
Sanding Drum ...................................... 9-25246
Drill Chuck and Key ............................ 9-2980
Dust Collector ............................... See Catalog
Molding Head Guard 8"o ..................... 9-29523
Taper Jig ........................................ 9-3233
Auxiliary Table Cover ...................... See Catalog
Miter Square ...................................... 9-32056
Pin Router ........................................ 9-32765
Extension Table ................................... 9-32787
Satin Cut Dado
7". .............................................. 9-3257
8". .............................................. 9-3253
8" Carbide ................................... 9-3264
Standard Cut Dado
8". ........................................................ 9-32475
ITEM CAT,, NOr
Adjustable Dado
7", 24 Tooth Carbide .............................. 9-326t
7", 32 Tooth Carbide .......................... 9-3262
7", t6 Tooth Carbide ............................. 9-3263
8", 48 Tooth Carbide ............................. 9-32708
Molding Heads
7" Bits not included .......................... 9-3214
7", 27 Piece Set ................................... 9-3217
7", !5 Piece Set .............................. 9-3218
Sanding Wheel, !0" o............................. 9-22723
Blade Stabilizer ................................. 9-2952
Cabinet Accessories
Shelf .................................... 9-22251
Door. ..................................... 9-22252
3 Drawer Set ................................. 9-22253
'eLower Retractable Guard
(For 90 ° Crosscut Only) ..................... 9-29009
The above recommended accessories are current
and were available at the time this manual was
printed
*NOTE:This lower retractable-guard isdesigned to provide
additional protection to the operator in an axial
direction to the sawblade (perpendicular to the
plane of the sawblade),
(a) When NOT in the cut (guards in full down
position (touching the table) and carriage in fult
rear position behind fence):
(b) When saw is set up to perform 90 ° crosscut
operations (sawblade 90 ° to table surface and
arm in 90 ° crosscut position),
The lower retractable guard wilt NOT provide protec-
tion to the operator, either crosscutting or ripping:
(a) Axially when in the cut, because the inner and
outer guards ride on top of the fence or workpiece
during the cutting operation, exposing the teeth
of the sawbtade;
(b) Radially (in a direction in line with the cutting
teeth);
(c) Obliquely (at an angle to the guard and saw-
blade), between the axial and radial directions
Power Tool Know How Handbook ......... See Catalog
eMeets OSHA Requirements as of 8-73
Potential risks of injury may be introduced if the
lower retractable guard is used for other- than 90 °
crosscut operations, including:
(a) Becoming caught or jammed in prior kerfs in the
fence or table;
(b) Giving the operator a false sense of security
when performing miter, bevel, and rip cuts;
(c) Jamming when setting-up, and while operating,
for bevel and compound miter cuts
(d) Jamming for certain in-rip cuts
The following warning appears on the Lower Outer
Guard:
WARNING:
TO AVOID INJURY
SHUT OFF POWER
BEFORE CLEARING A
,JAMMED LOWER GUARD
__....... ....... _....... _._
5O
Loading ...
Loading ...
Loading ...