Loading ...
Loading ...
Loading ...
OPERATION NO. 6 - BEVEL RIPPING
Bevel ripping is either in-ripping or out-ripping as
described above, except the saw blade is tilted out of
perpendicular to the saw table surface The radial
arm is indexed at 0 ° and locked, the bevel is set to
the desired bevel angle and the yoke is positioned
for in=ripping (saw blade at rear) or outripping (saw
blade at front), as required All requirements and
observations applicable to normal ripping operations
also apply to bevel ripping
DADOING
Instructions for operating the different dado blades
are contained in Owner's Manual furnished with the
dado.
The saw arbor is designed for a dado up to 13/16
inches wide. Using a wider dado on the arbor could
cause the dado and arbor nut to spin off. Take
several passes of the dado if cut required is greater
than 13/16 of an inch wide
For best results and to avoid excessive load on the
motor never cut a 13/16 of an inch wide dado deeper
than 3/8 of an inch in one pass,
When installing the dado on the arbor, always install
the inside "loose collar" first to ensure good arbor
nut engagement Do not install the outside blade
collar Make sure the arbor nut is snug, install the
arbor nut directly against the outside of the dado
MOLDING
instructions for operating the molding head are
contained in an Owner's Manual furnished with the
molding head.
EDGING
Use of the dado or molding head in the horizontal
position (parallel to table) requires the proper acces-
sory guard be used (See recommended accessories
page 50).
Use of the dado or molding head in the horizontal
position requires an auxiliary fence (page 39), or
that the radial arm be positioned as follows:
1 Miter the arm to the left approximately 30 °
2, Swivel the motor until bottom of motor is parallel
to and facing the rip fence and operating instruc-
tions label is visible
3, Follow all steps outlined on motor label
4. A copy of the label reads as follows:
DANGER
Know this tool:
t Read and Underefend ell wnrnlngs _nd InstructlonB on
Sew, In Owner's Monoel end with recommended eccee.-
eotJeg
2 Properly guard the cutting 3 Provide proper workplace
tool sttppott
4 Position the culling teat
#__ _ehind tha fenca by may÷
log the arm tO the taft and
clamping the yoke so this
label feces the fence: or
COI_,_fOCf _n s_Y_l|ta!ry
fence pet Owner'e Man,-
uel
_ S W_fh powe_" _ff the sw_tCh
key removed, turn cutting
tool by t_end to make sure
_.O_r_:¢_ __ it deo_ got =ttlke gue#d,
lance or any other mow
pads t_,,i,*,
38
For use of the molding head or drum sander with saw
arbor' vertical the rear table requires an opening
(next to rear face of fence) for arbor clearance. Cut
opening directly below arbor in vertical position.
Opening should be:
REAR TABLE -_[ _ 3" 3-1/2"
For top side use of the dado (rabbeting) or molding
head in the in-rip position locate the desired position
on the area and lock the rip lock handle. Lower the
arm into the fence very slowly, remove only as much
material from the fence as is necessary.. This will
provide maximum support for the workplace.
WARNING: NEVER USE A DADO HEAD OR MOLD-
ING HEAD WITH THE SAW ARBOR VERTICAL
WITHOUT INSTALLING AND ADJUSTING A
MOLDING HEAD/DADO GUARD, FOR TOP-SIDE
DADOING OR MOLDING INSTALL AND ADJUST
THE SAWBLADE GUARD AND ANTI-KICKBACK
ASSEMBLY FOR RIPPING OR CROSSCUTTING
AS APPROPRIATE.
Loading ...
Loading ...
Loading ...