Loading ...
Loading ...
Loading ...
5756
CULTIVATOR EDGER PRUNING SAW HEDGE TRIMMER BRUSHCUTTER
10. Exhaust Gas Precautions
DANGER
Do not run the engine in a room or in any confined area where
exhaust emissions can accumulate. Doing so can result in an
accumulation of carbon monoxide and other poisonous gases that
can cause death or severe poisoning.
11. Cutting Blades Precautions
DANGER
• Keep your hands and feet a safe distance from the cutting
blades while the tiller is in operation.
• If you need to touch the tines in order to untangle vines or the
like, first shut off the engine and allow the cutting blades to
come to a full stop.
• Even after the cutting blades have stopped, wear heavyduty
gloves and handle the cutting blades with care. The edges
of the cutting blades are very sharp and can cause death or
severe injury.
12. The Hazard Area
WARNING
• Keep the working end of the machine away from power cables,
telephone wires, and all other cables. The machine is not
insulated against external electric shock. Electric shock can
lead to death or severe injury.
• Do not operate the device within 15 meters of a child, animal,
or bystander. Consider a 15-meter radius around the device to
be a “hazard area.”
• If someone approaches the hazard area, immediately shut off
the engine.
Operation of the machine can result in falling or flying objects that
can lead to death or severe injury.
13. Limit your worktime
WARNING
• Rest for 10 to 20 minutes after every 30 to 40 minutes of
operation.Continuing to operate the machine without a
break can result in excessive fatigue. The resulting loss of
attentiveness can lead to an accident or problems with your
fingers or hands. If you experience any abnormal symptoms
such as pain, discomfort, or paralysis of the fingers or hand,
immediately stop operating the machine and seek medical
attention.
14. Avoiding Electric Shock
WARNING
Never touch the spark plug cap or high-voltage wire while the
device is running. Doing so can result in a highvoltage electric shock
that can cause death or severe injury.
15. Avoiding Burns
CAUTION
Never touch the muffler, muffler cover, exhaust pipe, cylinder or
cylinder head while the machine is running or immediately after
operation, as they become very hot.
Doing so can cause burns.
Ensuring Safe Operation
CAUTION
To ensure safety, strictly observe the following instructions. Failure to
do so can lead to personal injury or severe damage to the machine.
1. Pre-operation inspection
Carefully inspect and perform any necessary maintenance before
starting the machine. Failure to do so can lead to severe property
damage or damage to the machine.
a. Tighten or replace loose or lost screws.
b. Replace any damaged or worn parts.
c. Check for spilled fuel. Check the fuel tank cap and wipe off any
spilled fuel.
d. Check the cutting blades for chips, cracks, deformation, and
excessive wear.
For more information, see Inspection and maintenance.
2. Removing obstacles from the work area
Before starting operation, remove obstacles from the work area. Be
extremely careful about obstacles that can trip the operator, such as
tree roots, stumps, and holes.
3. Marking the hazard area
A circular area within a radius of 15 meters of the machine is the
hazard area. When necessary, mark the rope and post a warning
sign.
4. Wearing the Harness
• Put on the harness before starting to work with the machine.
• Adjust the length of the harness belt so that you can hold the
machine comfortably.
5. Starting the engine
• In some cases, the cutting blades can suddenly begin to run
when the engine is started. Keep a safe distance from the
blades when starting the engine.
• Make sure that no bystanders are within 15 meters before
starting the engine.
• Place the machine on flat solid ground before starting the
engine.
• Ensure that nothing is in contact with the cutting blades,
including the ground.
Operation
The tilling width of the cultivator is approximately 300mm. Place
cultivator in area to be tilled, hold unit firmly with left hand on front
grip and right hand on rear grip and gradually engage throttle
trigger. Guide the cultivator allowing the tines to pull forward; the soil
hardness will control tilling speed.
The cultivator attachment is capable of tilling in the forward or
reverse direction, for deep soil tilling. Till forward then lightly pull unit
rearward allowing the tines to make a deeper cut into the soil. Deep
soil cultivating can also be enhanced by repositioning the tines.
To raise or aerate the soil, tilt engine closer to the ground which will
raise cultivator tines higher relative to the soil surface
IMPORTANT
Do not operate cultivator under water, the gear housing is not
sealed and water will wash away lubrication damaging gears,
bearings, and seals.
Assembly
Attaching The Tools To The Drive Shaft Assembly
• Rest the power unit/shaft assembly on a flat firm surface.
• Ensure that the clamping wing nut (2) is loose, pull out locator
pin (1).
• Carefully fit attachment drive shaft assembly (5) into coupler (3).
• After the attachment drive shaft is in the coupler, release the
locator pin (1).
• Turn the attachment drive shaft until the locator pin engages
with the locating hole (4) in the drive
• shaft, when this has happened it will not be possible to twist
the drive shaft.
• Secure the drive shaft by tightening the clamping wing nut (2).
Transportation
• Never transport the multi-tool with the engine running.
Loading ...
Loading ...
Loading ...