Loading ...
Loading ...
Loading ...
the supply circuit) or when the supply circuit is
extremely long. Always check connections, load and
supply circuit when the motor fails to perform
satisfactorily. Check wire sizes and lengths with the
table in the next paragraph. Replace or repair damaged
or worn cord immediately.
CONNECTING TO POWER SOURCE OUTLET
This saw must be grounded while in use to protect the
operator from electrical shock.
If power cord is worn or cut, or damaged in any way, have
it replaced immediately.
CAUTION: This saw is wired for operation on 240 volts
only. Connect to a 15 ampere branch circuit protected by a
15 ampere time delay or circuit saver fuse or circuit
breaker,
WARNING: Do not permit fingers to contact the terminals
of power or motor plugs when installing or removing the
plug to or from a live power source. Hold the plug as
shown,
GROUNDING BLADE IS
LONGEST OF 3 BLADES
WARNING: IF NOT PROPERLY GROUNDED THIS
POWER TOOL CAN INCUR THE POTENTIAL HAZARD
OF ELECTRICAL SHOCK, PARTICULARLY WHEN
USED IN DAMP LOCATIONS, IN PROXIMITY TO
PLUMBING, OR OUT OF DOORS. IF AN ELECTRICAL
SHOCK OCCURS THERE IS THE POTENTIAL OF A
SECONDARY HAZARD SUCH AS YOUR HANDS
CONTACTING THE SAWBLADE.
This power tool is equipped with a 3-conductor cord and
grounding type plug which has a grounding prong, approved
by Underwriters' Laboratories and the Canadian Standards
Association. The ground conductor has a green lug and is
attached to the tool housing at one end and to the ground
prong in the attachment plug at the other end.
The use of any extension cord will cause some loss of
power. To keep this to a minimum and to prevent
over-heating and motor burn-out, use the table below to
determine the minimum wire size (A.W.G.) extension cord.
Use only 3 wire extension cords which have 3 prong
grounding type lugs and 3-pole receptacles which accept the
tools plug.
Extension Cord Length Wire Size A.W.G.
Up to 100 ft ......................... 14
100 ft. to 200ft ...................... 12
200 ft. to 400 ft ....................... 8
GROUNDED
OUTLET BOX
NO ADAPTER IS
AVAILABLE FOR
THIS TYPE PLUG
IF YOU ARE NOT SURE THAT YOUR OUTLET IS
PROPERLY GROUNDED, HAVE IT CHECKED BY A
QUALIFIED ELECTRICIAN.
WARNING: DO NOT PERMIT FINGERS TO TOUCH
THE TERMINALS OF PLUGS WHEN INSTALLING OR
REMOVING THE PLUG TO OR FROM THE OUTLET.
NOTE: For circuits of greater length, the wire size must be
increased proportionately in order to deliver ample voltage
to the saw motor.
_- SWITCH
GROUND GROUND
CONTENTS
WAR RANTY ................................. 2
GENERAL SAFETY INSTRUCTIONS
FOR POWER TOOLS ......................... 2
ADDITIONAL SAFETY INSTRUCTIONS
FOR TABLE SAWS ........................... 3
MOTOR SPECIFICATIONS AND ELECTRICAL
REQUIREMENTS ............................ 4
UNPACKING AND CHECKING CONTENTS ........ 6
Tools Needed ................................ 6
List of Loose Parts ............ -................ 6
ASSEMBLY .................................. 7
Attaching Legs ............................... 7
Checking Table Insert ......................... 7
Checking Blade Squareness to Table .............. 8
Attaching Table Extension ..................... 8
Installing Rip Fence Guide Bars .................. 9
Aligning Rip Fence .......................... 11
Adjusting Rip Scale Pointer .................... 12
Installing Blade Guard ........................ 12
GETTING TO KNOW YOUR SAW ............... !4
On-Off Switch .............................. 14
Elevation Crank ............................. 15
Elevation Lock ............................. 15
Tilt Crank ................................. 15
Rip Fence ................................. 15
Miter Gauge ................................ 15
Blade Guard ................................ 15
Table insert ................................ !5
Removing and Installing Saw Blade .............. 16
Exacti-Cut ................................. 16
BASIC SAW OPERATION USING THE MITER GAUGE 17
Work Helpers ............................... 17
Crosscutting ................................ 18
Repetitive Cutting ........................... 18
Miter Cutting ............................... 19
Bevel Crosscutting ........................... 19
Compound Miter Cutting ...................... 19
BASIC SAW OPERATION USING THE RIP FENCE .. 20
Ripping ................................... 20
Bevel Ripping .............................. 20
Resawing .................................. 22
Cutting Panels .............................. 22
Rabbeting ................................. 22
ADJUSTMENTS .............................. 23
M iter Gauge ................................ 23
Heeling Adjustment or Parallelism of
Sawblade to Miter Gauge Groove ............... 23
Blade Tilt, or Squareness of
Blade to Table ............................. 24
Elevation Lock ............................. 26
MAINTENANCE ............................ 26
LUBRICATION .............................. 27
RECOMMENDED ACCESSORIES ................ 2 7
TROUBLE SHOOTING ...................... 2S
REPAIR PARTS .............................. 30
Loading ...
Loading ...
Loading ...