Loading ...
Loading ...
Loading ...
ENGLISH
6
For your convenience and safety, the following warning
labels are on your mitersaw.
ON GUARD: ON BASE: (2 PLACES)
DANGER–KEEP AWAY
FROM BLADE
ON UPPER GUARD:
Properly secure bracket with both screws beforeuse.
ON TABLE: (2 PLACES)
WARNING: To reduce the risk of injury, user
must read instruction manual before operating
miter saw. Keep hands and body out of the
path of the saw blade. Contact with blade will
result in serious injury. Do not operate saw
without guards in place. Check lower guard for
proper closing before each use. Always tighten
adjustment knobs before use. Do not perform
any operation freehand. Clamp small pieces
before cutting. Never reach in back of saw blade.
Never cross arms in front of blade. Turn off tool
and wait for saw blade to stop before moving
workpiece, changing settings or moving hands.
Remove battery pack before adjusting, changing
blade or servicing. To reduce the risk of injury,
return carriage to the full rear position after each
crosscut operation.
WARNING: Since accessories, other than those
offered by CRAFTSMAN, have not been tested with
this product, use of such accessories with this tool
could be hazardous. To reduce the risk of injury, only
CRAFTSMAN recommended accessories should be
used with thisproduct. Recommended accessories
for use with your tool are available for purchase from
your local dealer or authorized service center. If you
need assistance in locating any accessory for your
tool, please contact CRAFTSMAN., 701 East Joppa
Road, Towson, MD 21286, call 1-888-331-4569 or visit
our website: www.CRAFTSMAN.com.
Optional Accessories
The following accessories, designed for your saw, may be
helpful. In some cases, other locally obtained work supports,
length stops, clamps, etc., may be more appropriate. Use
care in selecting and usingaccessories.
Saw Blades
ONLY USE 7-1/4" (184 mm) SAW BLADES WITH 5/8"
(16mm) DIAMETER ROUND ARBOR HOLES and a maximum
KERF of 2.1 mm. SPEED RATING MUST BE AT LEAST 4000
RPM. DO NOT USE BLADES WITH DIAMOND-SHAPED ARBOR
HOLES. Never use a different diameter blade. It will not be
guarded properly. Use crosscut blades only! Do not use
blades designed for ripping, combination blades or blades
with hook angles in excess of 7°.
BLADE DESCRIPTIONS
APPLICATION DIAMETER TEETH
General Purpose 7–1/4" (184 mm) 40
Fine Woodcutting 7–1/4" (184 mm) 60
The label on your tool may include the following symbols. The
symbols and their definitions are asfollows:
V ......................... volts
Hz .......................hertz
min ..................... minutes
or DC ......direct current
...................... Class I Construction
(grounded)
…/min ..............per minute
BPM .................... beats per minute
IPM ..................... impacts per minute
RPM .................... revolutions per
minute
sfpm ................... surface feet per
minute
SPM .................... strokes per minute
OPM .................... oscillations per
minute
A ......................... amperes
W ........................watts
or AC ...........alternating current
or AC/DC .... alternating or
direct current
...................... Class II
Construction
(double insulated)
n
o
.......................no load speed
n .........................rated speed
......................earthing terminal
.....................safety alert symbol
.....................visible radiation
..................... avoid staring at
light
..................... wear respiratory
protection
..................... wear eye
protection
..................... wear hearing
protection
..................... read all
documentation
IPXX .................... IP symbol
READ ALL INSTRUCTIONS
Important Safety Instructions for All
Battery Packs
WARNING: Read all safety warnings,
instructions, and cautionary markings for the
battery pack, charger and product. Failure to
follow the warnings and instructions may result
in electric shock, fire and/or serious injury.
• Do not charge or use the battery pack in explosive
atmospheres, such as in the presence of flammable
liquids, gases or dust. Inserting or removing the battery
pack from the charger may ignite the dust orfumes.
BATTERIES AND CHARGERS
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the
safety instructions below and then follow charging
proceduresoutlined. When ordering replacement battery
packs, be sure to include the catalog number andvoltage.
Loading ...
Loading ...
Loading ...