Loading ...
Loading ...
Loading ...
9
ENGLISH
A charger will not charge a faulty battery pack. The charger
refusing to light could indicate a problem with the charger.
NOTE: If the charger refuses to light, take the charger and
battery pack to be tested at an authorized servicecenter.
Hot/Cold Pack Delay
When the charger detects a battery pack that is too hot
or too cold, it automatically starts a Hot/Cold Pack Delay,
suspending charging until the battery pack has reached an
appropriate temperature. The charger then automatically
switches to the pack charging mode. This feature ensures
maximum battery packlife.
A cold battery pack may charge at a slower rate than a
warm batterypack.
Important Charging Notes
1. Longest life and best performance can be obtained if
the battery pack is charged when the air temperature
is between 65°F – 75°F (18° – 24°C). DO NOT charge
when the battery pack is below +40°F (+4.5°C), or
above +104°F (+40°C). This is important and will
prevent serious damage to the batterypack.
2. The charger and battery pack may become warm to the
touch while charging. This is a normal condition, and
does not indicate a problem. To facilitate the cooling of
the battery pack after use, avoid placing the charger or
battery pack in a warm environment such as in a metal
shed or an uninsulatedtrailer.
3. If the battery pack does not charge properly:
a. Check operation of receptacle by plugging in a lamp
or other appliance;
b. Check to see if receptacle is connected to a light
switch which turns power off when you turn out
the lights;
c. Move the charger and battery pack to a location
where the surrounding air temperature is
approximately 65°F – 75°F (18° – 24°C);
d. If charging problems persist, take the tool, battery
pack and charger to your local servicecenter.
4. The battery pack should be recharged when it fails to
produce sufficient power on jobs which were easily
done previously. DO NOT CONTINUE to use under these
conditions. Follow the charging procedure. You may
also charge a partially used pack whenever you desire
with no adverse effect on the batterypack.
5. Foreign materials of a conductive nature such as, but
not limited to, grinding dust, metal chips, steel wool,
aluminum foil, or any buildup of metallic particles
should be kept away from charger cavities. Always
unplug the charger from the power supply when there
is no battery pack in the cavity. Unplug the charger
before attempting toclean.
6. Do not freeze or immerse the charger in water or any
otherliquid.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger using
SAVE THESE INSTRUCTIONS FOR
FUTURE USE
Unpacking Your Saw
Check the contents of your miter saw carton to make sure
that you have received allparts.
In addition to this instruction manual, the carton should
contain:
1 CMCS714 miter saw
1 7–1/4" (184 mm) diameter saw blade
1 1/4" (6 mm) hex wrench
1 Charger (Kit only)
1 Battery (Kit only)
1 Dust bag
1 Material clamp
1 Miter lock knob
Specifications
Capacity of cut
Height Width
0º Miter / 0º Bevel 2" (50.8mm) 8" (209.5 mm)
45º Meter / 0º Bevel 2" (50.8mm) 5.75" (146 mm)
48º Miter / 0º Bevel 2" (50.8mm) 6" (152.4 mm)
45º Bevel - Left /
0º Miter
1.5" (38.1 mm) 8" (203 mm)
Crown Nested 9/16" x 3–5/8" (14.3 x 92 mm)
Base molding 5/8" x 3–1/2" (15.8 x 89 mm)
NOTE: Your saw is capable of cutting the following once a
special setup procedure is followed. Refer to SpecialCuts.
a cloth or soft non-metallic brush. Do not use water or
any cleaningsolutions.
Wall Mounting
These chargers are designed to be wall mountable or to
sit upright on a table or work surface. If wall mounting,
locate the charger within reach of an electrical outlet,
and away from a corner or other obstructions which may
impede air flow. Use the back of the charger as a template
for the location of the mounting screws on the wall. Mount
the charger securely using drywall screws (purchased
separately) at least 1" (25.4 mm) long, with a screw head
diameter of 0.28–0.35" (7–9mm), screwed into wood to an
optimal depth leaving approximately 7/32" (5.5 mm) of the
screw exposed. Align the slots on the back of the charger
with the exposed screws and fully engage them in theslots.
Versatrack
CRAFTSMAN chargers can be mounted to the wall using
CRAFTSMAN Versatrack Trackwall. Hooks and accessories
are sold separately. Please refer to the Versatrack Trackwall
accessory sheet for furtherinformation.
Loading ...
Loading ...
Loading ...