Loading ...
Loading ...
Loading ...
4
INSTALLATION REQUIREMENTS
Tools and Parts
Gather the required tools and parts before starting
installation.Read and follow the instructions provided
withanytools listed here.
Tools Needed
■ Level
■ Drill with 1
1
/
4
" (3.2 cm),
1
/
8
" (3.2 mm),
and
5
/
16
"(7.9 mm)drillbits
■ Pencil
■ Wire stripper or utility knife
■ Tape measure or ruler
■ Pliers
■ Caulking gun and weatherproof caulking compound
■ Vent clamps
■ Jigsaw or keyhole saw
■ Flat-blade screwdriver
■ Metal snips
■ Phillips screwdriver
■ T20
®
Torx
®†
adapter
Parts Needed
■ Home power supply cable
■
1
/
2
" (12.7 mm) UL listed or CSA approved strain relief
■ 3 UL listed wire connectors
For Vented Installations, You Will Also Need:
■ 1 wall or roof cap
■ Metal vent system
For Non-Vented (Recirculating) Installations,
YouWillAlsoNeed:
■ Recirculation Kit for non-vented (recirculating) installations
only. See the “Assistance or Service” section to order.
■ 6" (15.2 cm) diameter round metal vent duct -
lengthrequiredis determined by ceiling height.
Parts Supplied
Remove parts from packages. Check that all parts are included.
■ Hood canopy assembly with blower, LED lights and
canopyglass already installed
■ Vent transition with back draft dampers installed
■ Vent cover support bracket
■ Metal grease lter
■ Mounting template
■ 2-piece vent cover
■ 2 - 3.5 x 9.5 mm mounting screws (Phillips)
■ 4 - 4 x 8 mm screws (T20
®†
drive)
■ 6 - 5 x 45 mm mounting screws (#2 Phillips)
■ 4 - 8 x 40 mm wall anchors
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Have a qualied technician install the range hood. It is the
installer’s responsibility to comply with installation clearances
specied on the model/serial/rating plate. The model/serial/
rating plate is located behind the left lter on the rear wall
ofthevent hood.
Canopy hood location should be away from strong draft areas,
such as windows, doors, and strong heating vents.
Cabinet opening dimensions that are shown must be used.
Given dimensions provide minimum clearance.
This range hood is recommended for use with cooktops with
amaximum total rating of 65,000 BTUs or less.
Grounded electrical outlet is required. See the “Electrical
Requirements” section.
The canopy hood is factory set for venting through the roof
or wall. For non-vented (recirculating) installation, see “For
non-vented (recirculating) installation only” in the “Connect
Vent System” section. Recirculation Kit is available from your
dealer or an authorized parts distributor. See the “Assistance or
Service” section to order.
All openings in ceiling and wall where canopy hood will be
installed must be sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title
24CFR, Part 328 (formerly the Federal Standard for Mobile
Home Construction and Safety, Title 24, HUD, Part 280)
or, whensuch standard is not applicable, the standard for
Manufactured Home Installation 1982 (Manufactured Home
Sites, Communities and Setups) ANSI A225.1/NFPA 501A,
orlatest edition, or with local codes.
Product Dimensions
30"(76.2 cm) or
36" (91.4cm)
17
11
/
16
"(45 cm)
13
3
/
16
"(33.5 cm)
10
13
/
16
"(27.5 cm)
†
®
TORX and T20 are registered trademarks of Acument Intellectual Properties, LLC.
Loading ...
Loading ...
Loading ...