Documents: Go to download!
User Manual
- User Manual - (English, French)
- What comes in the carton
- How to assemble your vacuum cleaner
- How to identify parts of your vacuum cleaner
- How to use your vacuum cleaner
- How to use accessories
- How to maintain dust cup and filters
- How to clear a blockage
- How to maintain brushroll
- How to maintain turbo brush
- How to replace brushroll or belt
- Problem solving
Table of contents
Use Manual Vacuum
What comes in the carton
s
Accessories may vary depending on which model was purchased.
How to assemble your vacuum cleaner
Put the vacuum cleaner main body in the upright position.
Slide handle into top of vacuum cleaner. Push down until it clicks.
Store accessories on back of vacuum cleaner.
Loop hose under the hose hook.
Loop hose over hose retainer.
Push loose end of hose securely onto hose inlet.
Store turbo brush on front of handle. Align brush opening with slot and push to snap tool into clip.
How to identify parts of your vacuum cleaner
For filter maintenance instructions, see page 9
How to use your vacuum cleaner
Grab onto the end of cord and pull it out until the yellow tape is visible.
Step on the cord rewind pedal to retract the cord when needed.
Plug power cord into outlet.
Turn height adjustment knob to adjust from bare floors to high pile carpet.
Step on power switch to turn vacuum cleaner on. Step on again to turn off.
Step on front of the floor nozzle and recline the vacuum back from the handle to vacuum floors.
Empty dust cup after every use
Press release button and lift off dust cup.
To empty debris, press lever to release bottom lid.
How to use accessories
CAUTION When using tools, always place handle in upright position. Make sure vacuum cleaner is turned off while attaching tools.
|
Crevice tool – Use for baseboard edges, corners, detailing chairs, sofas, dryer vents and tight spaces.
Upholstery tool – Use for furniture, chairs, sofas and mattresses.
Dusting brush – Use for furniture, drapes, blinds, drawers and vents.
Turbo brush – Use to remove pet hair from stairs, carpet and upholstery
How to maintain dust cup and filters
Dust cup – Empty after each use
Press release button and lift off dust cup.
Hold dust cup over wastebasket and press lever to release bottom lid. Debris will empty.
Close bottom lid until it clicks.
Washable dust cup filters – Clean monthly
Pull dust cup latch to lift up dust cup lid.
Lift out foam filter and shake off dust. Rinse foam filter and dry THOROUGHLY.
Grip tabs and lift out filter screen. Twist bottom of filter screen counterclockwise to unlock and pull apart. Shake off dust. Rinse screen and dust cup. Dry all THOROUGHLY. Reassemble screen; twist clockwise to lock.
Align tab on filter screen with slot on back of dust cup and drop into position.
Reinstall foam filter.
Close cover until it clicks.
Warning: Never operate vacuum cleaner without foam filter, filter screen and dust cup in proper position.
How to clear a blockage
CAUTION Make sure vacuum is turned off and power cord is unplugged.
If vacuum is not cleaning floors, or if no suction at end of hose, check to be sure air path is not blocked.
|
|
How to maintain brushroll
CAUTION Make sure vacuum is turned off and power cord is unplugged.
|
How to maintain turbo brush
Grasp collar and twist to unlock cover. Lift cover up.
With cover open, use figers or small brush to clear accumulated pet hair from bristles.
Close cover and twist collar to lock.
How to replace brushroll or belt
CAUTION Make sure vacuum is turned off and power cord is unplugged.
|
Problem solving
Motor will not start.
• Push plug securely into outlet, try another outlet or check circuit breaker.
• Step on power switch to turn vacuum on.
• See detailed “thermal cut-off” instructions above.
Vacuum cleaner does not clean floors.
• Empty dust cup, clean and/or change filter.
• Clean or replace filter regularly to maintain suction.
• Check vacuum height adjustment knob position.
• Clean brushroll if needed. Page 11.
No suction at the end of hose or wand.
• See other solutions above.
• Remove clogs from the hose or wand that restrict the airflow. Page 10. Burning smell; brushroll will not turn.
• Check brushroll for debris.
• Replace broken or out of shape belt. Page 12.
Vacuum is hard to push.
• Adjust vacuum height knob to a higher position.
• Check brushroll for debris and clean if needed. Page 11. Turbo brush will not turn.
• Check turbo brush for debris. Page 11.
Cord will not retract.
• Pull out slightly and then step on the cord rewind pedal again.
• Make sure the cord has a clear path and is not twisted.
See other models: NEU100