Documents: Go to download!
- Owner's manual - (English)
- How to identify parts of your Vacuum Cleaner
- Easy assembly
- How to maintain your vacuum cleaner
- How to maintain brushroll
- Problem solving
Table of contents
User manual Vacuum Cleaner
How to identify parts of your Vacuum Cleaner
Cordless Vacuum Cleaner
Easy assembly
1. Slide wand onto hand vacuum until it clicks (Fig. 1).
2. Push wand into motorized floor nozzle until it clicks (Fig. 2).
How to install wall mount
- Choose location near power outlet.Locate point high enough on wallto allow wand and motorized floornozzle to hang freely.
- Place mount against wall and usepencil to mark drill holes.
- Drill holes (with 1/4” bit) and insertdrywall anchors. Insert screwsthrough holes on mount and tightenuntil firmly attached ( Fig.3).
How to charge battery and store accessories
- Place assembled vacuum cleaner on wall mount.
- Plug charger into power outlet and then into charger port on handle ( Fig.4).
- Loop charger cord into clips on sides of wall mount.
Battery Indicator lights show level of charge (Fig. 4):
A. Fully charged
B. Half charged
- Indicator lights stop blinking when fully charged.
- Charge battery fully before using for the first time. This may take up to six hours.
How to use cleaner for cleaning floors
- Click power button once to start ( Fig.1). Vacuum starts on medium mode. Usemode button to switch between modes.
- Using motorized floor nozzle, glideback and forth on area to be cleaned.Avoid oversized or sharp items (such asscrews) with cleaner.
- Twist wrist to engage swivel function.
- When done, click power button once tostop engine.
Empty dust cup after every use
- Click the dust cup release button,located on the front of the handle justabove the dust cup and pull dust cupout ( Fig.2).
- Press lever to release bottom lid of dustcup to empty debris. ( Fig.2).
- To place the dust cup back, angle itforward so the lower hook catches inthe slot and then gently push it back towards the wand until you hear click indicating it is locked in place. ( Fig.3)
How to use hand vacuum and accessories
The hand vacuum can be used with orwithout tools.
- To use without tools, press release button and remove wand. Collect debris directly with hand vacuum nozzle ( Fig.4).
- To use tools with wand, press releasebutton to remove motorized floor nozzle. Slide tool onto end of wand until it clicks ( Fig.5).
- To use tools with hand vacuum only,press release button to remove wand.Slide tool onto hand vacuum until it clicks.
Use with or without wand.
- 2-in-1 upholstery tool: Use brush to vacuum blinds, vents or upholstered surfaces. Use felt portion to clean delicate surfaces. To switch between felt and brush portions, press thumb release and slide brush up or down.
How to use hand vacuumand motorized floor nozzle
Ideal for cleaning stairs.
- Press release button to remove wand from hand vacuum.Attach motorized floor nozzle directly to hand vacuum until it clicks.
- Click power button onceto start. Vacuum starts onmedium mode. Use mode button to switch between modes depending on suction power desired.
How to maintain your vacuum cleaner
Dust cup - Empty after each use
Click the dust cup release button, located on the front of the handle just above the dust cup and pull dust cup out.
Press lever to release bottom lid of dust cup to empty debris.
Washable dust cup filter - clean montly
1. Click the dust cup release button, located on the front of the handle just above the dust cup and pull dust cup out.
2. Lift out pre-motor filter and shake off dust frequently. Every three months rinse filter and dry THOROUGHLY.
3. Reattach filter and Cyclone.
4. Click dust cup back into place on unit.
Washable post-motor filter - clean every 6 months
1. Twist filter cover and remove.
2. Lift out post-motor filter.
3. Shake to remove dust.
4. Every 6 months, replace filter or rinse and dry THOROUGHLY.
5. Reposition filter and cover and twist to 'clock.'
How to maintain brushroll
To avoid unnecessary service calls. periodically check brushroll for debris. if brushroll gets clogged it will automatically shut off. Turn vacuum off and unplug before attempting to remove clog.
Brushroll maintenance - clean frequently or when brushroll indicator light turns red.
Place motorized floor nozzle upside down. Use scissors or knife to cut strings and threads.
If debris cannot be removed easily. remove retainer clip to acess brushroll. Using flathead screwdriver or coin. turn. serew to the unlock’ position.
Remove retainer clip and lift out brushroll to clean and remove debris.
To reassemble:
- Align one end of brushroll with floor nozzle gear.
- Press other end into slot.
- Hook retainer clip under tab and press down.
- Insert screw and tum to lock’ position.
Problem solving
Problem | Solution |
Motor will not start |
|
Charging indicator lights are not lit while charging |
|
Not enough suction power |
|
Not enough running time |
|
Brushroll will not turn |
|
See other models: ERK-FT-43 3670H NEC180 3684F 3670G