Loading ...
Loading ...
Loading ...
12
Closed and Engaged Position
To Remove Roll-Out Extension Rack:
1. Slide the rack in completely so that it is closed and engaged
with the sliding shelf.
2. Using two hands, lift up on the front edge of the rack and push
the sliding shelf to the back wall of the oven so that the front
edge of the sliding shelf sits on the rack guides. The front edge
of the rack and the sliding shelf should be higher than the back
edge.
3. Pull the rack and the sliding shelf out.
To Replace Roll-Out Extension Rack
1. Using two hands, grasp the front of the closed rack and the
sliding shelf. Place the closed rack and the sliding shelf on the
rack guide.
2. Using two hands, lift up on the front edge of the rack and the
sliding shelf together.
3. Slowly push the rack and the sliding shelf to the back of the
oven until the back edge of the rack pulls over the end of the
rack guide.
To avoid damage to the sliding shelves, do not place more
than 25 lbs (11.4 kg) on the rack.
Do not clean the roll-out extension rack in a dishwasher.
It may remove the rack’s lubricant and affect its ability to slide.
See the “General Cleaning” section for more information.
B
A
A. Roll-out extension rack
B. Sliding shelf
B
A
C
A. Sliding shelf
B. Rack guide
C. Roll-out extension rack
Oven Vent(s)
The oven vent(s) should not be blocked or covered since they
allow the inlet of fresh air into the cooling system. Also, the bottom
vent should not be blocked or covered since it allows the inlet of
fresh air into the cooling system and the outlet of hot air from the
cooling system. Blocking or covering vents will cause poor air
circulation, affecting cooking, cleaning, and cooling results.
Preheating and Oven Temperature
Preheating
When beginning a Bake, Convect Bake, or Convect Roast cycle,
the oven will begin preheating after Start is pressed. The oven
will take approximately 12 to 17 minutes to reach 350°F (177°C)
with all of the oven racks provided with your oven inside the
oven cavity. Higher temperatures will take longer to preheat.
The preheat cycle rapidly increases the oven temperature. The
actual oven temperature will go above your set temperature to
offset the heat lost when your oven door is opened to insert food.
This ensures that when you place your food in the oven, the oven,
will begin at the proper temperature. Insert your food when the
preheat tone sounds. Do not open the door during preheat before
the tone sounds.
Rapid Preheat
Rapid Preheat can be used to shorten the preheating time. Only
one standard flat oven rack should be in the oven during Rapid
Preheat. Extra racks should be removed prior to starting. The
preheating cycle should be completed before placing food in the
oven. When the Rapid Preheat cycle is complete, the oven starts a
normal Bake cycle.
IMPORTANT: Rapid Preheat should be used only for one-rack
baking.
Oven Temperature
While in use, the oven elements will cycle on and off as needed
to maintain a consistent temperature, but they may run slightly
hot or cool at any point in time due to this cycling. Opening the
oven door while in use will release the hot air and cool the oven
which could impact the cooking time and performance. It is
recommended to use the oven light to monitor cooking progress.
NOTE: On models with convection, the convection fan may run in
the non-convection bake mode to improve oven performance.
Before baking and roasting, position racks according to the
“Positioning Racks and Bakeware” section. When roasting,
it is not necessary to wait for the oven preheat cycle to end
before putting food in unless it is recommended in the recipe.
B
A
C
A. Microwave
B. Oven Vent
C. Lower Oven
Loading ...
Loading ...
Loading ...