Loading ...
Loading ...
Loading ...
Care and Cleaning cont.
Figure 2
Figure 3
Remove
Knobs
Remove
Screw.
Pressfirmlyon eachsideof
caseto releaselocking tabs;
Figure 4
Removing Decorative Front - Some Models
Front
Figure !
SliderCasement Front
• 6-waylouvermodelshaveaslideoutfilter. Grasptheformedhandleofthefilterand
pull it to the left, removing it from the front panel (Figure 2).
• Formost installations in the window, this front may need to be removed to access
the filter for cleaning (Figure3). To remove the front, reversethe installation process
for SideAir Discharge Models shown in Front Installation.
• Somemodels require the louvers to be tilted in the up position, before pulling the
filter out. Placethe thimb under the center handle and pinch the top of the filter bar
with your forefinger while pulling the filter up and out asshpwn in Figure 6.
Washfilter usingaliquid dishwashingdetergent and warm water. Rinsefilter thoroughly.
Gently shakeexcesswater from the filter. Dryfilter thoroughly before replacing.
Cabinet Cleaning
• Besureto unplug the air conditioner to preventshock or fire hazard.Thecabinet and
front maybedustedwith anoil-free clothor washedwith acloth dampenedinasolution
of warm water and mild liquid dishwashingdetergent. Rinsethoroughly andwipe dry.
• Never useharsh cleaners,wax or polish on the cabinet front.
• Besure to wring excesswater from the cloth before wiping around the controls.
Excesswater in or around the controls may cause damage to the air conditioner.
• The cabinet front can be removed for more thorough cleaning. Refer to "Front
Installation" in this manual and Figures4 and 5.
• Cleanthe front in a sink using liquid dishwashing detergent and warm
water. Rinsethoroughly and dry. Becareful not to disturb soft sealson the front.
• Replacecabinet front. Replacethe screws or hex nuts.
• Replacefront panel and filter. Plug in air conditioner.
Decorative Front and Dial Plate Removal
1. Unplug power cord from the wall outlet.
2. Removeknobsbypullingfirmly, andthen removedialplate.Removefront retainingscrew
from thefront (seeFigure4 or 5 for screwlocation,whicheverissimilarto your model).
3. Pressfirmly on each sideof the metal casecloseto the front, approximately half way
down for Figure 4, or 2/3 the way down from Figure 5 from the top of the front
4. While pressing on the sides of the metal case, gently pull the front out and lif
up to release it from the case.
To reinstall:
Properreinstallation of decorative front isimportant for both safety and performance.
2. Position the top of the decorative front on the top flange of the case and align
the tabs on the front with the slots in the case. On some models remove the filter
to expose the two (2) front retaining screws.
3. Carefully pull down on the front to engage the top tabs while pushing the front
over the caseto ensure proper alignment. The side locking tabs will "click" when
the front is properly installed.
4. Install the front retaining screw (seeFigure 4 or 5 for screw location, whichever
is similar to your model).
5. Install the knobs by aligning them with their shafts and pushing firmly into place.
Winter Storage
Ifyouplanto storetheairconditioner duringthe winter, removeitcarefullyfrom thewindow
accordingtotheinstallationinstructions.Coveritwith plasticor returnittotheoriginalcarton.
NOTE: To prevent rust or electrical connectionsfrom being damaged, store air
conditionerinanupright positionanda dryplace.Awintercovercanbepurchasedfrom
ourdealer.Thecoverwillprotecttheairconditionerwhen itisleftinplacethroughthewinter.
3. Pull Filter Out and Up
1. Tilt Louver
Up
Louver
2. Pinch Center
Handle Here
Loading ...
Loading ...
Loading ...