User Manual ElectriQ EIQWMTL75 7.5kg 1200rpm Freestanding Top Loading Washing Machine

• Owner's manual - (English)

Table of contents

• PRODUCT OVERVIEW
• OPERATION
• CONTROL PANEL
• PROGRAMMES
• WASHING PROGRAMME TABLE
• LEVELLING
• HOSE CONNECTION
• CLEANING AND MAINTENANCE
• TROUBLESHOOTING

PRODUCT OVERVIEW

ACCESSORIES

OPERATION

Before washing, the washing machine should be operated without clothes in as follows.

BEFORE EACH WASH

The working condition of the washer should be (0-40) ℃. If used under 0℃, the inlet valve and draining system may become frozen and damaged.

Please check the labels and the explanation of using detergent before wash. Use non-foaming or less-foaming detergent.

DETERGENT DISPENSER

• Please choose suitable type of detergent for the various washing temperature to get the best washing performance with less water and energy consumption.

CONTROL PANEL

PRE-WASH:

The Prewash function can get an extra wash before main wash. You need to put detergent into the Case (I) when it is selected.

EXTRA RINSE:

The laundry will undergo an extra rinse once after you select it.

DELAY:

Set the Delay function:
1. Select a programme.
2. Press the Delay button to choose the time (the delay time is 0-24 H/3H-6H9H).
3. Press [Start/Pause] to commence the delay operation.

CANCEL THE DELAY FUNCTION:

Press the [Delay] button until the display shows 0H. It should be pressed before starting the programme. If the programme has already started, you should switch off the programme to reset a new one.

NOTE: If there is any break in the power supply while the machine is operating, the appliance stores the selected programme. When the power is restarted, the most recent program will continue.

TEMP:
Press the button to regulate the temperature (Cold,20 40℃,60℃,90℃).

SPIN:
Press the button to change the speed/ Mute.

CHILD LOCK:
Press Spin and Delay at the same time for 3 seconds to enter and exit child lock.

MUTE:
Press and hold the spin button for 3 seconds to mute the button sounds.

MY CYCLE:
Press and hold the Temp. button for 3 seconds to save your preferred programme.

PROGRAMMES

WASHING PROGRAMME TABLE

LEVELLING

1. Loosen the lock nut turn the feet until it closely contacts with the floor.

2. Adjust the legs and lock them with a spanner, make sure the machine is steady.

HOSE CONNECTION

CONNECTNG THE WATER SUPPLY HOSE

To prevent leakage or water damage, do not kink, crush, modify or sever water inlet hose.

CONNECTING THE SCREW TAP AND INLET HOSE

Connect the other end of inlet pipe to the inlet valve at the back of the product and fasten the pipe tightly in a clockwise direction.

DRAIN HOSE

Connect the other end of inlet pipe to the inlet valve at the backside of product and fasten the pipe tightly clockwise.

There are two ways to place the end of drain hose:

If the machine has drain hose support, please install it following the below instructions.

• If the drain hose is too long, do not force it into washing machine as it will cause abnormal noises.

• When installing drain hose, fix it properly with a rope.

CLEANING AND MAINTENANCE

NOTE: Ensure that the appliance is unplugged before cleaning and maintenance takes place.

The surface can be cleaned with diluted non-abrasive neutral detergents when necessary. If there is any water overflow, use a wet cloth to wipe it off immediately.

The rusts left inside the drum by the metal articles must be removed immediately with chlorine-free detergents. Never use steel wool. Don’t put laundry in the washing machine during the drum cleaning.

CLEANING THE INLET FILTER:

Washing the filter in the tap
1. Close the tap.
2. Remove the water supply hose from the tap.
3. Clean the filter.
4. Reconnect the water supply hose

WASHING THE FILTER IN WASHING MACHINE:

1. Screw off the inlet pipe from the backside of the machine.
2. Pull out the filter with long nose pliers and reinstall it back after being washed.
3. Reconnect the inlet pipe.

CLEANING THE DETERGENT DISPENSER

1. Open the dispenser compartment. Lift the clip up and take out softener cover and wash all grooves with water.

2. Restore the softener cover and push the drawer onto position.

CLEANING THE DRAIN PUMP FILTER

• Be careful of hot water
• Allow the detergent solution to cool down.
• Unplug the machine to avoid electrical shock before washing.
• Clean the filter periodically to ensure the normal operation of washing machine.

Make sure that the valve cap and emergency drain hose are reinstalled properly, cap plates should be inserted aligning to hole plates otherwise water may leak.

Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty. When replacing the cover, ensure it is securely re-tightened.

TROUBLESHOOTING