Loading ...
Loading ...
Loading ...
8. Appendix: Error/Warning Messages
115
Caution and Operation Messages
The following caution and operation messages may appear in the center of the screen.
Follow the instructions provided to resolve the issue.
Display message Cause and Solution
Battery Error
Please Change Battery
An error was detected in the battery pack.
Replace with a normal battery pack.
Backup Battery End
Please Change
The remaining capacity of the backup battery is insufficient.
Charge the backup battery.
Unknown Media (A)
1)
Please Change
A memory card that has been partitioned or a memory card
containing more clips that can be handled by the camcorder
was inserted.
The card cannot be used in the camcorder, and must be
replaced.
Cannot Use Media (A)
1)
Unsupported File System
A card using a different file system or an unformatted card
was inserted.
The card cannot be used in the camcorder, and must be
replaced or formatted using the camcorder.
Media Error
Media (A)
1)
Needs to be Restored
An error occurred on the memory card, and the card must be
restored.
Restore the memory card.
Media Error
Cannot Record to Media (A)
1)
The memory card may be damaged, and can no longer be
used for recording.
Playback is possible, so making a copy and replacing the
memory card is recommended.
Media Error
Cannot Use Media (A)
1)
The memory card may be damaged, and can no longer be
used for recording or playback.
The card cannot be used in the camcorder, and must be
replaced.
Media (A)
1)
Error
Recording Halted
Playback Halted
Recording and playback was stopped because an error
occurred while using the memory card.
If the problem persists, replace the memory card.
Media Reached Rewriting Limit
Change Media (A)
1)
The memory card has reached the end of its life.
Make a backup, and replace the card immediately. If you
continue using the card, the card may not be able to record or
play.
For details, refer to the operating instructions for the memory
card.
The specified address is invalid. The specified address is invalid.
Check that the setting is correct.
Cannot Use Specified Port Number The specified port number is invalid.
Check that the setting is correct.
Display message Cause and Solution
Fan Stopped The built-in fan stopped.
Avoid use at high temperatures, disconnect the power, and
contact your Sony service representative.
Lens I/F Error(xx:xx) A lens error was detected in the lens I/F communication when
an E-mount lens was attached.
Check the status of the connection with the E-mount lens.
If the problem persists, contact your Sony service
representative with the error code (five characters in
parentheses).
This Multi Term. acc is not supported
by the device and cannot be used.
Please verify the compatibility.
An incompatible accessory was detected.
The only Multi Terminal accessory supported by the unit is the
supplied grip remote control.
Failed This error may appear if an address cannot be obtained with
DHCP set to On.
Check the DHCP server settings.
Cannot add auto upload job of Proxy
file because maximum number of
upload jobs was reached.
The maximum number of transfer jobs has been reached.
Clear any unwanted jobs. The auto upload destination setting
for proxy files may also be incorrect. Check that the setting is
correct.
<SSID>Not found. Network (access point) with the specified <SSID> could not be
found.
Check that the setting is correct.
<SSID>Authentication Failed Connection authentication on the network (access point) with
the specified <SSID> failed.
Check that the password and other settings are correct.
An IP address conflict has occurred.
Please check the network settings.
There is a conflict in the network addresses of the wireless
LAN, wired LAN, or USB tethering.
Change the address manually or change the settings for the
network router.
The IP address of the Wireless LAN
Access Point Mode has been
changed due to an IP address
conflict.
The IP address of the wireless LAN access point mode was
changed due to a conflict in the network addresses of the
wireless LAN access point mode, wired LAN, or USB tethering.
Check the IP address setting.
1) “(B)” is displayed for the card in slot B.
Loading ...
Loading ...
Loading ...