Loading ...
Loading ...
Loading ...
7. CLEANING AND MAINTENANCE
7.1 GENERAL
Before starting to clean your oven, be sure that all control knobs
are off and your appliance is cooled off. Unplug the appliance.
Do not use cleaning materials containing particles that might
scratch the enamelledand painted parts of your oven. Use cream
cleaners or liquid cleaners, which do not contain particles.
As they might harmthe surfaces, do not use caustic creams,
abrasive cleaning powders, rough wire wool or hard tools. In the
event the excess liquids spilling over your oven should burn, it may
cause a damage to the enamel. Immediately clean up the spilt
liquids.
7.2 CLEANING THE OVEN
Make sure to unplug the oven before starting to clean it.You will
obtain best results if you clean the oven interior while the oven is
slightly warm. Wipe your oven with a soft piece of cloth dampened
with soap water after each use. Then wipe it again, this time with a
wetted cloth, and wipe it dry. A complete cleaning may be
necessary from time to time, using a liquid cleaning material. Do
not clean using dry and powder type cleaners. For products with
catalytic enamel frames, the rear and side walls of the inner frame
do not require cleaning. However; depending on usage, it is
recommended that you replace them after a certain period of time.
7.3 CLEANING THE SOLID HOTPLATE HOB
Hobs should be cleaned wiping with a dampened cloth.Cleaning
of the stainless steel parts should be done only with water and
such parts should be wiped drywith a soft clothor chamois.
Gaps and corners should be cleaned usingliquid detergents or
lukewarm vinegar.
7.4 CLEANING THE VITROCERAMIC HOB
Unplug the appliance before starting the cleaning.
Wait for the vitroceramic glass to completely cool off before
starting the cleaning.
Make sure that the cleaning materials you will use do not contain
particles that might scratch the glass Use cream detergents or
liquid detergents.
The vitroceramic surface should be wiped with cold water and
wiped dry with a soft piece of cloth until no cleaning material is left
on the surface.
You can use the cleaning spatula, if supplied together with your
product, for the cleaning of spilt foods and residues.
Dessert type of foods should be cleaned immediately after they
spill without waiting for the vitroceramic glass to cool off.
Scrubbing with steel cleaning wires may harm the vitroceramic
glass surface. Formations of dust on the surface should be
cleaned up using a dampened cloth.
Changes in colour which might occur on the ceramic glass surface
do not affect the functional structure or permanence of the
vitroceramic. The reason for the changes in colour is not the
change in the material; it may be because the burnt residues on
the surface are not cleaned up or the pots used have worn the
glass surface or because unsui table cleaning materials were
used.
The cleaning spatula should always be used prior to chemical
cleaning substances. With this spatula, you can clean up the
tiniest of dirts on the vitroceramic surface Dirts that are difficult to
remove such as melted plastic, heavy oils, sweet substances, can
be removed easily with the spatula. As the spatula includes a
razor, it is dangerous and must be kept out of reach of children.
During cleaning with the spatula, pay attention not to scrape off the
sillicon adhesives found on the sides of the glass.
7.5 MAINTENANCE
Replacing the Oven Light Bulb
It is recommended that you leave this operation to the Authorised
Service.
Unplug the oven first and make sure that it is cold. After removing
the lid infront of the light, take the bulbout. Insert the new bulb
0
resistant to 300 C, which you will find at Authorised Services, into
the place of the bulb you have removed. Then fit the light
protecting lid back into its place. After that, your oven will be ready
for use.
8. SERVICE AND TRANSPORTATION
8.1 REQUIREMENTS BEFORE CONTACTING
TO SERVICE
If the oven does not operate ;
The oven may be plugged off, there has been a black out.
If the oven does not heat ;
The temperature may be not adjusted with oven’s temperature
control switch.
If the oven light does not operate does not light;
The electricity should be controlled.
It should be controlled whether the ulb is defective.
Cooking (If lower-upper part does not cook equally) ;
Control the shelf locations, cooking period and temperature
values according to the manual. In case of the product doesn't
work properly and malfunctioning causes cannot be found, switch
off the product. Please do not tamper with it and call the Technical
Service.
It is important to communicate to Authorized Technical Service the
product model and it's serial number that can be found on the
rating label.
8.2 INFORMATION RELATED TO TRANSPORT
If you need any transport ;
Keep the original packaging of product and carry it with its original
packaging when needed.
Follow the transport signs on the packaging.
If the original packaging is not available;
Take measure for the external surfaces (glass and painted
surfaces) of oven and hob aganist possible blows.
13 GB
Loading ...
Loading ...
Loading ...