Loading ...
Loading ...
Loading ...
16 17
1. Unscrew the hanger fastening screw at the bottom of the hanger (fig. 7).
2. Hold the hanger such that the Roll & Press system handle is on the same side as the locking
hook.
3. Insert the hanger vertically on the top of the pole. The holes at the bottom of the hanger and
in the pole should be at the same level (fig. 8).
4. Put the screw back and screw in as far as it will go so that the hanger is firmly fixed to the
pole (fig. 9).
5. Install the steam head between the hanger hooks.
2 • Filling the water tank
IMPORTANT: Your product is designed to operate using untreated tap water. If your
water is very hard (check with your local water authority) it is possible to mix untreated
tap water with store-bought distilled water in the following proportions 50% untreated
tap water with 50% distilled water. Heat concentrates the elements contained in water
during evaporation. The types of water listed below may contain organic waste, mineral
or chemical elements that can cause spitting, brown staining or premature wear of the
appliance: water from clothes dryers, scented or softened water, water from refrigerators,
batteries, air conditioners, rain water, boiled, filtered or bottled water. These types of water
should not be used. Only use store bought distilled water as advised above.
• Ensure that the steamer is unplugged. Remove the water tank from the base of the appliance
by pulling the handle upwards (fig. 10). Unscrew the tank cap and fill the tank (fig. 11).
Maximum capacity is indicated by the “max” mark.
• After closing the cap, turn the tank down and hold it by the handle. Check that no water is
leaking through the cap.
• Place the water tank on the base (fig. 12).
USE
WARNING: Never steam a garment while it is being worn.
The flexible pipe and the end of the steam head can become extremely hot during
use. This is perfectly normal. Be careful and avoid any prolonged contact.
1 • Setting up
• Only operate the steamer on the floor clear of any materials which may obstruct the base
of the steamer, ensure the floor is dry, flat, stable and heat-resistant. Do not obstruct the
openings on the lower part of the appliance. This device should not be used on very thick
carpets or rugs.
• Undo the Velcro strip and completely unwind the electrical cord.
• Plug in to power socket (fig.13).
• Switch on by pressing the pedal located at the front of the device. The power indicator light
will come on (fig.14).
• The device will begin producing steam after approximately 60 seconds.
2 • Using the Roll & Press system
To use the Roll & Press system:
• Hold the Roll & Press system handle and roll down the panel (fig. 15).
DESCRIPTION
13. Electric cord
14. Velcro strip
15. Pole fastening screw
16. Steam hose connector
17. Removable water tank
18. ON/OFF pedal
19. Transport wheels
20. Textile steam hose
21. On/ off light
22. Built in accessories
a. Fabric brush
b. Lint pad
c. Delicates steam cap
BEFORE USE
1 • Garment steamer assembly
Pole assembly
1. Unscrew the fastening screw on the base of the pole (fig. 1).
2. Hold the pole such that the cord holder is on the left. Check that the 2 pole clips are
unlocked (fig. 2).
3. Insert the pole into the base by pressing downwards until the holes of the pole and
base are at the same level, so that you can put the screw back. If the holes are not
aligned, check that the clips of the pole are well and truly unlocked (fig. 3).
4. Screw the pole fastening screw back in as far as it will go so that the pole is firmly
fixed to the base (fig. 4).
5. Adjust the pole to its maximum height by sliding it upwards (fig. 5) then locking the 2 clips
(fig. 6). Make sure the 3 segments of the pole are fully extended.
Hanger with Roll & Press system assembly
Before first use
• When you first use the appliance, some smoke or a harmless odour may be produced or there
may be a small discharge of particles. This will not affect the use of the appliance and will
disappear quickly.
What water to use?
• Your appliance has been designed to use tap water.
If your water is very hard, mix 50% tap water and 50% bottled demineralised water.
Never use water containing additives (starch, perfume, aromatic substances, softeners, etc.), or
condensation water (for example water from tumble dryers, water from refrigerators, water
from air conditioning units, rainwater). This water contains organic waste materials or minerals
that concentrate
under the effect of heat and cause spitting, brown colouring or premature ageing of
your appliance.
SAVE THESE INSTRUCTIONS
Environmental protection first!
i Your appliance contains valuable materials which can be recovered or recycled.
When disposing of it, take it to a local civic waste collection point.
9100021252-01 IS6300 M2-D2.indd 17 21/07/2016 10:41
Loading ...
Loading ...
Loading ...