Loading ...
Loading ...
Loading ...
62
MAINTENANCE
SpeedClean™ Instruction Guide
1
Remove oven racks and accessories from the oven.
2
Scrape off and remove any burnt-on debris with
a plastic scraper.
Suggested plastic scrapers:
•
Hard plastic spatula
•
Plastic pan scraper
•
Plastic paint scraper
•
Old credit card
3
Fill a spray bottle with
2
/
5
(4 oz or 120 ml) of
water and use the spray bottle to thoroughly
spray the inside surfaces of the oven.
4
Use at least 2 oz or 60 ml of the water to completely
saturate the soil on both the walls and in the
corners of the oven. Spray or pour the remaining
water onto the bottom center of the oven cavity.
5
Fill and spray or pour the remaining 10 oz or 300
ml of water (for right oven) and 8 oz or 240 ml of
water (for left oven) onto the bottom center of the
each oven cavity. The indentation on the oven
bottom should be fully covered to submerge all
soils. Add water if necessary.
NOTE
Use the "mist" setting on the spray bottle for better
coverage. The entire 14 oz or 410 ml of water
(for right oven) and 10 oz or 300 ml of water (for
left oven) should be used for each oven cavity
cleaned. Do not spray water directly on the door.
Doing so will result in water dripping to the floor.
6
Close the oven door. Select the desired oven
and touch SpeedClean™ and Start in that order.
CAUTION
•
Some surfaces may be hot after the
SpeedClean™ cycle. Wear rubber gloves while
cleaning to prevent burns.
•
During the SpeedClean™ cycle, the oven may
become hot enough to cause burns. After the
cycle ends, open the oven door and wait 5
minutes before wiping the inside surface of the
oven. Failure to do so may result in burns.
•
Avoid leaning or resting on the oven door glass
while cleaning the oven cavity.
7
A tone will sound at the end of the 10 minute
cycle. Touch End of Cleaning to clear the
display and end the tone.
8
After the cleaning cycle and during
hand-cleaning, enough water should remain
on the oven bottom to completely submerge all
soils. Add water if necessary. Place a towel on
the floor in front of the oven to capture any water
that may spill out during hand-cleaning.
9
Clean the oven cavity immediately after the
SpeedClean™ cycle by scrubbing with a wet,
non-scratch scouring sponge or
pad. (The scouring side will not
scratch the finish.)
NOTE
Do not use any steel scouring pads, abrasive
pads or cleaners as these materials can
permanently damage the oven surface.
10
Once the oven cavity is cleaned, wipe any
excess water with a clean dry towel. Replace
racks and any other accessories.
11
If some light soils remain, repeat the above
steps, making sure to thoroughly soak the
soiled areas. If stubborn soils remain after
multiple SpeedClean™ cycles, run the Self
Clean cycle. Be sure that the oven cavity is
empty of oven racks and other accessories,
and that the oven cavity surface is dry before
running the Self Clean cycle. Consult the Self
Clean section of your owner’s manual for
further details.
NOTE
•
If you forget to saturate the inside of the oven
with water before starting SpeedClean™,
press Stop to end the cycle. Wait for the range
to cool to room temperature and then spray
or pour water into the oven and start another
SpeedClean™ cycle.
•
The cavity gasket may be wet when the
SpeedClean™ cycle finishes. This is normal.
Do not clean the gasket.
•
If mineral deposits remain on the oven bottom
after cleaning, use a cloth or sponge soaked in
vinegar to remove them.
•
It is normal for the fan to operate during the
SpeedClean™ cycle.
Loading ...
Loading ...
Loading ...