NutriBullet N17-1007M Nature’s Prescription RX 1700W 10-Piece Set

USER GUIDE - Transcript

• Page 1: USER GUIDE NATURES PRESCRIPTION
• Page 2 - English - : 2 3 IMPORTANT SAFEGUARDS AND CAUTIONARY INFORMATION SAVE THESE INSTRUCTIONS FOR YOUR SAFETY CAREFULLY READ ALL INSTRUCTIONS BEFORE OPERATING YOUR NUTRIBULLET Rx MEDICAL WARNING IF YOU ARE TAKING ANY MEDICATION ESPECIALLY CHOLESTEROLLOWERING MEDICATION BLOOD THINNERS BLOOD PRESSURE DRUGS TRANQUILIZERS OR ANTIDEPRESSANTS PLEASE CHECK WITH YOUR DOCTOR BEFORE CONSUMING ANY OF THE NUTRIBLAST Rx RECIPES THE FOLLOWING LIST OF SEEDS AND PITS CONTAIN CHEMICALS THAT RELEASE CYANIDE INTO THE BODY WHEN INGESTED DO NOT USE THE FOLLOWING SEEDS AND PITS IN THE NUTRIBULLET Rx APPLE SEEDS APRICOT PITS CHERRY PITS PLUM PITS PEACH PITS ELECTRICAL SAFETY When using any electrical appliance basic safety precautions should always be observed including the following CAUTION TO AVOID RISK OF ELECTRIC SHOCK NEVER IMMERSE THE CORD PLUG OR POWER BASE OF BLENDER IN WATER OR OTHER LIQUIDS DO NOT USE THIS PRODUCT WITH ANY TYPE OF ADAPTOR OR VOLTAGE CONVERTER DEVICE THE USE OF ATTACHMENTS INCLUDING CANNING JARS NOT RECOMMENDED OR SOLD BY MANUFACTURER MAY CAUSE FIRE ELECTRIC SHOCK OR INJURY AND VOID THE WARRANTY USE OF ADAPTERS AND CONVERTERS IS CONSIDERED AN UNAUTHORIZED MODIFICATION OF THE PRODUCT AND AS SUCH WILL VOID THE WARRANTY USE OF THIS PRODUCT IN LOCATIONS WITH DIFFERENT ELECTRICAL SPECIFICATIONS MAY RESULT IN DAMAGE TO THE PRODUCT UNPLUG THE NUTRIBULLET Rx AND DEPRESS POWER BUTTON WHEN IT IS NOT IN USE MAKE SURE THE POWER BASE IS UNPLUGGED BEFORE ASSEMBLING DISASSEMBLING ADDING ADDITIONAL PARTS OR CLEANING Do not pull twist or damage the power cord Do not allow the cord to hang over the side of the counter or table Do not allow cord to touch hot surfaces including stove Periodically inspect cord and plug for damage Do not operate any appliance with a damaged cord or plug If the appliance malfunctions or is dropped or damaged in any manner discontinue use Contact Customer Service for assistance in obtaining a replacement Do not remove the rubber liner inside the power base To clean unplug first then wipe with a sponge moistened with warm water THIS APPLIANCE CAN BE USED BY CHILDREN AGED FROM 8 YEARS AND ABOVE AND PERSONS WITH REDUCED PHYSICAL SENSORY OR MENTAL CAPABILITIES OR LACK OF EXPERIENCE AND KNOWLEDGE IF THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE IN A SAFE WAY AND UNDERSTAND THE HAZARDS INVOLVED IF THE SUPPLY CORD IS DAMAGED IT MUST BE REPLACED BY THE MANUFACTURER ITS SERVICE AGENT OR SIMILARLY QUALIFIED PERSONS IN ORDER TO AVOID A HAZARD DEPRESS POWER BUTTON TO SWITCH OFF THE APPLIANCE AFTER EACH USE DISCONNECT FROM POWER SOURCE BEFORE CHANGING ACCESSORIES OR APPROACHING PARTS THAT MOVE IN USE SHALL WARN OF POTENTIAL INJURY FROM MISUSE SHALL STATE THAT CARE SHALL BE TAKEN WHEN HANDLING THE SHARP CUTTING BLADES EMPTYING THE PITCHER CUP AND DURING CLEANING CHILDREN SHALL NOT PLAY WITH THE APPLIANCE CLEANING AND USER MAINTENANCE SHALL NOT BE MADE BY CHILDREN WITHOUT SUPERVISION WARNING VENTILATION CAUTION Always operate the NUTRIBULLET on level surface leaving unobstructed space beneath and around the power base to permit proper air circulation Slots and openings on the of bottom the product are provided for ventilation to ensure reliable motor operation and to prevent overheating Warning To prevent fire hazard power base openings should be free of dust or lint and never obstructed with flammable materials such as newspapers tablecloths napkins dishtowels or place mats
• Page 3 - English - : 2 3 IMPORTANT SAFEGUARDS AND CAUTIONARY INFORMATION SAVE THESE INSTRUCTIONS FOR YOUR SAFETY CAREFULLY READ ALL INSTRUCTIONS BEFORE OPERATING YOUR NUTRIBULLET Rx MEDICAL WARNING IF YOU ARE TAKING ANY MEDICATION ESPECIALLY CHOLESTEROLLOWERING MEDICATION BLOOD THINNERS BLOOD PRESSURE DRUGS TRANQUILIZERS OR ANTIDEPRESSANTS PLEASE CHECK WITH YOUR DOCTOR BEFORE CONSUMING ANY OF THE NUTRIBLAST Rx RECIPES THE FOLLOWING LIST OF SEEDS AND PITS CONTAIN CHEMICALS THAT RELEASE CYANIDE INTO THE BODY WHEN INGESTED DO NOT USE THE FOLLOWING SEEDS AND PITS IN THE NUTRIBULLET Rx APPLE SEEDS APRICOT PITS CHERRY PITS PLUM PITS PEACH PITS ELECTRICAL SAFETY When using any electrical appliance basic safety precautions should always be observed including the following CAUTION TO AVOID RISK OF ELECTRIC SHOCK NEVER IMMERSE THE CORD PLUG OR POWER BASE OF BLENDER IN WATER OR OTHER LIQUIDS DO NOT USE THIS PRODUCT WITH ANY TYPE OF ADAPTOR OR VOLTAGE CONVERTER DEVICE THE USE OF ATTACHMENTS INCLUDING CANNING JARS NOT RECOMMENDED OR SOLD BY MANUFACTURER MAY CAUSE FIRE ELECTRIC SHOCK OR INJURY AND VOID THE WARRANTY USE OF ADAPTERS AND CONVERTERS IS CONSIDERED AN UNAUTHORIZED MODIFICATION OF THE PRODUCT AND AS SUCH WILL VOID THE WARRANTY USE OF THIS PRODUCT IN LOCATIONS WITH DIFFERENT ELECTRICAL SPECIFICATIONS MAY RESULT IN DAMAGE TO THE PRODUCT UNPLUG THE NUTRIBULLET Rx AND DEPRESS POWER BUTTON WHEN IT IS NOT IN USE MAKE SURE THE POWER BASE IS UNPLUGGED BEFORE ASSEMBLING DISASSEMBLING ADDING ADDITIONAL PARTS OR CLEANING Do not pull twist or damage the power cord Do not allow the cord to hang over the side of the counter or table Do not allow cord to touch hot surfaces including stove Periodically inspect cord and plug for damage Do not operate any appliance with a damaged cord or plug If the appliance malfunctions or is dropped or damaged in any manner discontinue use Contact Customer Service for assistance in obtaining a replacement Do not remove the rubber liner inside the power base To clean unplug first then wipe with a sponge moistened with warm water THIS APPLIANCE CAN BE USED BY CHILDREN AGED FROM 8 YEARS AND ABOVE AND PERSONS WITH REDUCED PHYSICAL SENSORY OR MENTAL CAPABILITIES OR LACK OF EXPERIENCE AND KNOWLEDGE IF THEY HAVE BEEN GIVEN SUPERVISION OR INSTRUCTION CONCERNING USE OF THE APPLIANCE IN A SAFE WAY AND UNDERSTAND THE HAZARDS INVOLVED IF THE SUPPLY CORD IS DAMAGED IT MUST BE REPLACED BY THE MANUFACTURER ITS SERVICE AGENT OR SIMILARLY QUALIFIED PERSONS IN ORDER TO AVOID A HAZARD DEPRESS POWER BUTTON TO SWITCH OFF THE APPLIANCE AFTER EACH USE DISCONNECT FROM POWER SOURCE BEFORE CHANGING ACCESSORIES OR APPROACHING PARTS THAT MOVE IN USE SHALL WARN OF POTENTIAL INJURY FROM MISUSE SHALL STATE THAT CARE SHALL BE TAKEN WHEN HANDLING THE SHARP CUTTING BLADES EMPTYING THE PITCHER CUP AND DURING CLEANING CHILDREN SHALL NOT PLAY WITH THE APPLIANCE CLEANING AND USER MAINTENANCE SHALL NOT BE MADE BY CHILDREN WITHOUT SUPERVISION WARNING VENTILATION CAUTION Always operate the NUTRIBULLET on level surface leaving unobstructed space beneath and around the power base to permit proper air circulation Slots and openings on the of bottom the product are provided for ventilation to ensure reliable motor operation and to prevent overheating Warning To prevent fire hazard power base openings should be free of dust or lint and never obstructed with flammable materials such as newspapers tablecloths napkins dishtowels or place mats
• Page 4 - English - : 4 5 EXTRACTION SAFETY PRECAUTIONS The NUTRIBULLET Rx has two modes NutriBlast Rx Mode traditional Blast mode and Souperblast Mode Soup making mode which are further explained in the How It Works section of this manual Carefully read and follow all the safety precautions particularly when operating the NUTRIBULLET Rx in SouperBlast mode NEVER LEAVE THE NUTRIBULLET Rx UNATTENDED WHILE IN USE CLOSE SUPERVISION IS NECESSARY WHEN ANY APPLIANCE IS USED BY OR NEAR CHILDREN NEVER USE THE EXTRACTOR BLADE TO BLEND WITHOUT LIQUID AS DOING SO MAY DAMAGE THE BLADE NEVER PUT YOUR HANDS OR UTENSILS NEAR THE MOVING BLADE AND NEVER USE YOUR HANDS OR UTENSILS TO PRESS THE ACTIVATOR BUTTONS DOWN WHILE THE NUTRIBULLET Rx IS PLUGGED IN BLADES ARE SHARP HANDLE CAREFULLY USE CARE WHILE HANDLING THE BLADES NOT TO TOUCH THE BLADE EDGES TO AVOID INJURY CHECK GASKET TO MAKE SURE IT IS COMPLETELY SEATED IN THE CROSS BLADE UNIT BEFORE EACH USE CONTACT CUSTOMER SERVICE FOR ASSISTANCE IF GASKET IS NOT COMPLETELY SEATED THE NUTRIBULLET Rx IS NOT INTENDED FOR USE IN MICROWAVE OVENS DO NOT PLACE THE NUTRIBULLET Rx CUPS POWER BASE OR ANY NUTRIBULLET ACCESSORY IN A MICROWAVE OVEN AS THIS MAY RESULT IN DAMAGE TO THE APPLIANCE TO REHEAT SOUPS AFTER BLENDING TRANSFER TO A MICROWAVE SAFE CONTAINER OR TO A STOVETOP POT PRIOR TO HEATING NEVER MICROWAVE UNVENTED SEALED CONTAINERS AS THEIR CONTENTS MAY EXPAND WITH HEAT PRESSURE AND EXPLODE RESULTING IN POSSIBLE INJURY OR PROPERTY DAMAGE NEVER BLEND CARBONATED BEVERAGES BUILTUP PRESSURE FROM RELEASED GASES CAN CAUSE CONTAINER TO BURST RESULTING IN POSSIBLE INJURY DO NOT PUT HOT LIQUIDS IN ANY OF THE BLENDING VESSELS BEFORE BLENDING START WITH COOL OR ROOM TEMPERATURE INGREDIENTS 21ºC70ºF OR LESS SOUP WILL HEAT DURING THE EXTRACTION PROCESS TO 65ºC150ºF DO NOT RUN THE NUTRIBULLET Rx WITH EMPTY NUTRIBULLET Rx CUPS OR SOUPBLAST PITCHER AS THIS CAN DAMAGE THE UNIT AFTER BLENDING INGREDIENTS REMOVE THE BLADE ASSEMBLYALLOW THE VESSEL WITH ITS CONTENTS TO SETTLE AND TO RELEASE ANY PRESSURE THAT MAY HAVE BUILT UP DURING THE EXTRACTION PROCESS IF YOU WILL NOT CONSUME IT IMMEDIATELY USE THE STAY FRESH LID TO CLOSE THE CONTAINER UNSCREW THE LID AND RELEASE PRESSURE PERIODICALLY IF STORING LONGER THAN A FEW HOURS TO RELEASE ANY ADDED PRESSURE THAT MAY HAVE BUILT UP DUE TO FERMENTATION NEVER PERMIT ANY BLENDED MIXTURE TO SIT INSIDE A CUP SEALED WITH A BLADE BASE WITHOUT FIRST RELEASING THE PRESSURE DO NOT ALLOW NUTRIBLASTS OR SOUPERBLASTS TO SIT FOR LONG PERIODS IN A SEALED CONTAINER BY UNSCREWING THE LID AND OPENING THE CUP FOR A FEW MOMENTS THE SUGARS IN THE FRUIT AND VEGETABLES CAN FERMENT CAUSING PRESSURE TO BUILD UP AND EXPAND IN THE VESSEL WHICH CAN CAUSE INGREDIENTS TO BURST AND SPRAY OUT WHEN MOVED OR OPENED RELEASE PRESSURE BY CAREFULLY UNSCREWING THE LID AND OPENING THE CUP FOR A FEW MOMENTS Avoid contact with moving parts TO REDUCE THE RISK OF INJURY NEVER PLACE CUTTERASSEMBLY BLADES ON BASE WITHOUT JAR PROPERLY ATTACHED NEVER PUT THE EXTRACTOR BLADE ON THE POWER BASE WITHOUT BEING SECURELY ASSEMBLED ONTO CUP FIRST Always operate blender with cover in place Keep hands and utensils away from the cutting blade while chopping or blending food to reduce the risk of severe personal injury or damage to the device A scraper may be used but only when the blenderfood chopper is not running Do not use the cross blade for grinding dry materials such as grains cereal or coffee To reduce the risk of injury make sure the blade base is securely screwed onto the cup before placing it on the Power Base and operating the appliance Do not use NUTRIBULLET Rx outdoors DO NOT BLEND HOT LIQUIDS
• Page 5 - English - : 4 5 EXTRACTION SAFETY PRECAUTIONS The NUTRIBULLET Rx has two modes NutriBlast Rx Mode traditional Blast mode and Souperblast Mode Soup making mode which are further explained in the How It Works section of this manual Carefully read and follow all the safety precautions particularly when operating the NUTRIBULLET Rx in SouperBlast mode NEVER LEAVE THE NUTRIBULLET Rx UNATTENDED WHILE IN USE CLOSE SUPERVISION IS NECESSARY WHEN ANY APPLIANCE IS USED BY OR NEAR CHILDREN NEVER USE THE EXTRACTOR BLADE TO BLEND WITHOUT LIQUID AS DOING SO MAY DAMAGE THE BLADE NEVER PUT YOUR HANDS OR UTENSILS NEAR THE MOVING BLADE AND NEVER USE YOUR HANDS OR UTENSILS TO PRESS THE ACTIVATOR BUTTONS DOWN WHILE THE NUTRIBULLET Rx IS PLUGGED IN BLADES ARE SHARP HANDLE CAREFULLY USE CARE WHILE HANDLING THE BLADES NOT TO TOUCH THE BLADE EDGES TO AVOID INJURY CHECK GASKET TO MAKE SURE IT IS COMPLETELY SEATED IN THE CROSS BLADE UNIT BEFORE EACH USE CONTACT CUSTOMER SERVICE FOR ASSISTANCE IF GASKET IS NOT COMPLETELY SEATED THE NUTRIBULLET Rx IS NOT INTENDED FOR USE IN MICROWAVE OVENS DO NOT PLACE THE NUTRIBULLET Rx CUPS POWER BASE OR ANY NUTRIBULLET ACCESSORY IN A MICROWAVE OVEN AS THIS MAY RESULT IN DAMAGE TO THE APPLIANCE TO REHEAT SOUPS AFTER BLENDING TRANSFER TO A MICROWAVE SAFE CONTAINER OR TO A STOVETOP POT PRIOR TO HEATING NEVER MICROWAVE UNVENTED SEALED CONTAINERS AS THEIR CONTENTS MAY EXPAND WITH HEAT PRESSURE AND EXPLODE RESULTING IN POSSIBLE INJURY OR PROPERTY DAMAGE NEVER BLEND CARBONATED BEVERAGES BUILTUP PRESSURE FROM RELEASED GASES CAN CAUSE CONTAINER TO BURST RESULTING IN POSSIBLE INJURY DO NOT PUT HOT LIQUIDS IN ANY OF THE BLENDING VESSELS BEFORE BLENDING START WITH COOL OR ROOM TEMPERATURE INGREDIENTS 21ºC70ºF OR LESS SOUP WILL HEAT DURING THE EXTRACTION PROCESS TO 65ºC150ºF DO NOT RUN THE NUTRIBULLET Rx WITH EMPTY NUTRIBULLET Rx CUPS OR SOUPBLAST PITCHER AS THIS CAN DAMAGE THE UNIT AFTER BLENDING INGREDIENTS REMOVE THE BLADE ASSEMBLYALLOW THE VESSEL WITH ITS CONTENTS TO SETTLE AND TO RELEASE ANY PRESSURE THAT MAY HAVE BUILT UP DURING THE EXTRACTION PROCESS IF YOU WILL NOT CONSUME IT IMMEDIATELY USE THE STAY FRESH LID TO CLOSE THE CONTAINER UNSCREW THE LID AND RELEASE PRESSURE PERIODICALLY IF STORING LONGER THAN A FEW HOURS TO RELEASE ANY ADDED PRESSURE THAT MAY HAVE BUILT UP DUE TO FERMENTATION NEVER PERMIT ANY BLENDED MIXTURE TO SIT INSIDE A CUP SEALED WITH A BLADE BASE WITHOUT FIRST RELEASING THE PRESSURE DO NOT ALLOW NUTRIBLASTS OR SOUPERBLASTS TO SIT FOR LONG PERIODS IN A SEALED CONTAINER BY UNSCREWING THE LID AND OPENING THE CUP FOR A FEW MOMENTS THE SUGARS IN THE FRUIT AND VEGETABLES CAN FERMENT CAUSING PRESSURE TO BUILD UP AND EXPAND IN THE VESSEL WHICH CAN CAUSE INGREDIENTS TO BURST AND SPRAY OUT WHEN MOVED OR OPENED RELEASE PRESSURE BY CAREFULLY UNSCREWING THE LID AND OPENING THE CUP FOR A FEW MOMENTS Avoid contact with moving parts TO REDUCE THE RISK OF INJURY NEVER PLACE CUTTERASSEMBLY BLADES ON BASE WITHOUT JAR PROPERLY ATTACHED NEVER PUT THE EXTRACTOR BLADE ON THE POWER BASE WITHOUT BEING SECURELY ASSEMBLED ONTO CUP FIRST Always operate blender with cover in place Keep hands and utensils away from the cutting blade while chopping or blending food to reduce the risk of severe personal injury or damage to the device A scraper may be used but only when the blenderfood chopper is not running Do not use the cross blade for grinding dry materials such as grains cereal or coffee To reduce the risk of injury make sure the blade base is securely screwed onto the cup before placing it on the Power Base and operating the appliance Do not use NUTRIBULLET Rx outdoors DO NOT BLEND HOT LIQUIDS
• Page 6 - English - : 6 7 SAFETY WARNINGS FOR EXTRACTING FOR NUTRIBLASTS NUTRIBULLET Rx IS PROGRAMMED TO RUN FOR 1 MINUTE DURING NUTRIBLAST MODE G BUTTON WILL BE GREEN IF POWER BASE DOES NOT SHUT OFF AFTER 1 MINUTE DURING NUTRIBLAST CYCLE STOP IT MANUALLY BY DEPRESSING THE POWER BUTTON LOCATED 90 TO THE LEFT SIDE OF THE GBUTTON OR SIMPLY LIFT CUP OFF POWER BASE TO TURN OFF THE MACHINE AT ANYTIME DURING THE NUTRIBLAST CYCLE G BUTTON WILL BE GREEN DEPRESS THE POWER BUTTON LOCATED 90 TO THE LEFT SIDE OF THE GBUTTON OR SIMPLY LIFT THE CUP OFF THE POWER BASE IF YOU PRESS THE G BUTTON FOR 2 SECONDS DURING EXTRACTION AND THE LIGHT TURNS RED YOU ARE IN SOUPERBLASTER MODE DEPRESS THE POWER BUTTON LOCATED 90 TO THE LEFT SIDE OF THE GBUTTON AND SIMPLY LIFT THE CUP OFF THE POWER BASE TO TURN OFF THE UNIT THE LIGHT WILL STOP GLOWING SIGNIFYING POWER IS OFF ALWAYS UNPLUG THE POWER BASE UPON COMPLETION OF PROCESSING DO NOT TOUCH COUPLING GEAR DIRECTLY WITH HANDS AFTER NUTRIBLAST MODE THE COUPLING GEAR IN BLADE BASE AND POWER BASE WILL BE HOT DO NOT RUN IN NUTRIBLAST MODE FOR MORE THAN 1 INTERVAL AFTER INITIAL CYCLE ALLOW POWER BASE TO SHUT OFF COMPLETELY AND WAIT FOR 15 SECONDS BEFORE STARTING ANOTHER CYCLE DO NOT RUN FOR MORE THAN 3 CONSECUTIVE 1 MINUTE INTERVALS WITHOUT ALLOWING POWER BASE TO COOL TO PREVENT OVERHEATING AND ALLOW INGREDIENTS TO SETTLE FOR 23 MINUTES AFTER THE 3RD EXTRACTION CYCLE POWER BASE IS EQUIPPED WITH AN INTERNAL THERMAL BREAKER THAT SHUTS OFF THE POWER BASE IF THE UNIT OVERHEATS IF THE POWER BASE OVERHEATS AND SHUTS OFF UNPLUG THE POWER BASE AND PRESS THE POWER BUTTON LOCATED 90 TO THE LEFT OF THE GBUTTON AND LET IT COOL FOR AN HOUR OR MORE BEFORE ATTEMPTING TO USE IT AGAIN POWER BASE WILL RESET WHEN THE UNIT IS POWERED OFF AND THE THERMAL BREAKER HAS COOLED DOWN SUFFICIENTLY WHEN MAKING NUT BUTTERS OR OILBASED FOODS DUE TO THE CONSISTENCY THE FOOD WILL PROCESS AND THEN STICK TO THE SIDES OF THE CUP PROCESS IN 30 SECOND INCREMENTS ONLY BY SIMPLY LIFTING THE CUP OFF THE POWER BASE BETWEEN INTERVALS BETWEEN CYCLES USE A COMBINATION OF THE TAP METHOD DESCRIBED ON PAGE 19 AND OPEN CUP AS NEEDED TO SCRAPE DOWN THE INGREDIENTS TO THE CENTER OF THE CUP BEFORE CONTINUING TO PROCESS IN 30 SECOND INCREMENTS ALLOW MACHINE TO COOL DOWN FOR 10 MIN AFTER 45 CYCLES TO PREVENT OVERHEATING AND DAMAGING THE UNIT To prevent leakage always align and handtighten or use blade remover to tighten the blade to the NutriBlast Rx cup prior to inverting it and placing the assembly on to the motor base TO TURN ON THE NUTRIBULLET Plug the power base into an electrical outlet Press the power button located 90 to the left side of the Gbutton This will cause the power button glow BLUE Next place the cup bladesidedown onto the power base This will activate the NutriBullet Rxs SMART Technology function causing the GButton at the front of the unit to glow GREEN Once activated the unit will run for 1 minute in regular NutriBlast Rx mode before it automatically turns off The Gbutton will stop glowing green at the end of the 1minute cycle To turn off completely before the cycle is complete either lift the cup off of the base or press the power button located 90 to the left side of the Gbutton The power button will extend from its recessed position and the blue light will no longer be lit signifying the power is off In NutriBlast Rx Mode the motor will run 2 cycles during the 1 minute interval first it will slow down half way through the 1 minute interval to allow the ingredients to settle for improved processing then it will powerup again for the second half of the interval This is a normal function of the NutriBullet Rx Turn the NUTRIBULLET Rx off after each use Depress the power button located 90 to the left side of the Gbutton The BLUE light will stop glowing signifying power is off POWER OFF INSTRUCTIONS To turn off the machine at anytime during the NutriBlast cycle indicated by the GREEN glowing Gbutton depress the power button located 90 to the left side of the Gbutton and simply lift the cup off power base When the vessel is removed from the power base only the GREEN Gbutton light will turn off When the power off button is pressed the BLUE light will turn off and the blade will stop spinning To turn off machine at any time during SouperBlast Mode indicated by the RED glowing G button press the power off button located 90 to the left side of the Gbutton and simply lift the SouperBlast Pitcher off the power base When the vessel is removed from the power base only the RED Gbutton light will turn off When the power off button is pressed the BLUE light will turn off and the blade will stop spinning Always press the power off button when machine is not in use
• Page 7 - English - : 6 7 SAFETY WARNINGS FOR EXTRACTING FOR NUTRIBLASTS NUTRIBULLET Rx IS PROGRAMMED TO RUN FOR 1 MINUTE DURING NUTRIBLAST MODE G BUTTON WILL BE GREEN IF POWER BASE DOES NOT SHUT OFF AFTER 1 MINUTE DURING NUTRIBLAST CYCLE STOP IT MANUALLY BY DEPRESSING THE POWER BUTTON LOCATED 90 TO THE LEFT SIDE OF THE GBUTTON OR SIMPLY LIFT CUP OFF POWER BASE TO TURN OFF THE MACHINE AT ANYTIME DURING THE NUTRIBLAST CYCLE G BUTTON WILL BE GREEN DEPRESS THE POWER BUTTON LOCATED 90 TO THE LEFT SIDE OF THE GBUTTON OR SIMPLY LIFT THE CUP OFF THE POWER BASE IF YOU PRESS THE G BUTTON FOR 2 SECONDS DURING EXTRACTION AND THE LIGHT TURNS RED YOU ARE IN SOUPERBLASTER MODE DEPRESS THE POWER BUTTON LOCATED 90 TO THE LEFT SIDE OF THE GBUTTON AND SIMPLY LIFT THE CUP OFF THE POWER BASE TO TURN OFF THE UNIT THE LIGHT WILL STOP GLOWING SIGNIFYING POWER IS OFF ALWAYS UNPLUG THE POWER BASE UPON COMPLETION OF PROCESSING DO NOT TOUCH COUPLING GEAR DIRECTLY WITH HANDS AFTER NUTRIBLAST MODE THE COUPLING GEAR IN BLADE BASE AND POWER BASE WILL BE HOT DO NOT RUN IN NUTRIBLAST MODE FOR MORE THAN 1 INTERVAL AFTER INITIAL CYCLE ALLOW POWER BASE TO SHUT OFF COMPLETELY AND WAIT FOR 15 SECONDS BEFORE STARTING ANOTHER CYCLE DO NOT RUN FOR MORE THAN 3 CONSECUTIVE 1 MINUTE INTERVALS WITHOUT ALLOWING POWER BASE TO COOL TO PREVENT OVERHEATING AND ALLOW INGREDIENTS TO SETTLE FOR 23 MINUTES AFTER THE 3RD EXTRACTION CYCLE POWER BASE IS EQUIPPED WITH AN INTERNAL THERMAL BREAKER THAT SHUTS OFF THE POWER BASE IF THE UNIT OVERHEATS IF THE POWER BASE OVERHEATS AND SHUTS OFF UNPLUG THE POWER BASE AND PRESS THE POWER BUTTON LOCATED 90 TO THE LEFT OF THE GBUTTON AND LET IT COOL FOR AN HOUR OR MORE BEFORE ATTEMPTING TO USE IT AGAIN POWER BASE WILL RESET WHEN THE UNIT IS POWERED OFF AND THE THERMAL BREAKER HAS COOLED DOWN SUFFICIENTLY WHEN MAKING NUT BUTTERS OR OILBASED FOODS DUE TO THE CONSISTENCY THE FOOD WILL PROCESS AND THEN STICK TO THE SIDES OF THE CUP PROCESS IN 30 SECOND INCREMENTS ONLY BY SIMPLY LIFTING THE CUP OFF THE POWER BASE BETWEEN INTERVALS BETWEEN CYCLES USE A COMBINATION OF THE TAP METHOD DESCRIBED ON PAGE 19 AND OPEN CUP AS NEEDED TO SCRAPE DOWN THE INGREDIENTS TO THE CENTER OF THE CUP BEFORE CONTINUING TO PROCESS IN 30 SECOND INCREMENTS ALLOW MACHINE TO COOL DOWN FOR 10 MIN AFTER 45 CYCLES TO PREVENT OVERHEATING AND DAMAGING THE UNIT To prevent leakage always align and handtighten or use blade remover to tighten the blade to the NutriBlast Rx cup prior to inverting it and placing the assembly on to the motor base TO TURN ON THE NUTRIBULLET Plug the power base into an electrical outlet Press the power button located 90 to the left side of the Gbutton This will cause the power button glow BLUE Next place the cup bladesidedown onto the power base This will activate the NutriBullet Rxs SMART Technology function causing the GButton at the front of the unit to glow GREEN Once activated the unit will run for 1 minute in regular NutriBlast Rx mode before it automatically turns off The Gbutton will stop glowing green at the end of the 1minute cycle To turn off completely before the cycle is complete either lift the cup off of the base or press the power button located 90 to the left side of the Gbutton The power button will extend from its recessed position and the blue light will no longer be lit signifying the power is off In NutriBlast Rx Mode the motor will run 2 cycles during the 1 minute interval first it will slow down half way through the 1 minute interval to allow the ingredients to settle for improved processing then it will powerup again for the second half of the interval This is a normal function of the NutriBullet Rx Turn the NUTRIBULLET Rx off after each use Depress the power button located 90 to the left side of the Gbutton The BLUE light will stop glowing signifying power is off POWER OFF INSTRUCTIONS To turn off the machine at anytime during the NutriBlast cycle indicated by the GREEN glowing Gbutton depress the power button located 90 to the left side of the Gbutton and simply lift the cup off power base When the vessel is removed from the power base only the GREEN Gbutton light will turn off When the power off button is pressed the BLUE light will turn off and the blade will stop spinning To turn off machine at any time during SouperBlast Mode indicated by the RED glowing G button press the power off button located 90 to the left side of the Gbutton and simply lift the SouperBlast Pitcher off the power base When the vessel is removed from the power base only the RED Gbutton light will turn off When the power off button is pressed the BLUE light will turn off and the blade will stop spinning Always press the power off button when machine is not in use
• Page 8 - English - : 8 9 SAFETY WARNINGS FOR EXTRACTING FOR SOUPS WARNING ONLY USE THE VENTED SOUPERBLAST PITCHER AND TWOPIECE LID WHILE OPERATING THE NUTRIBULLET Rx IN SOUPERBLAST MODE THE SOUPERBLAST PITCHER IS SPECIALLY VENTED TO RELEASE PRESSURE AS THE SOUP MIXTURE HEATS OTHER VESSELS ARE UNVENTED AND MAY RUPTURE AND CAUSE PERSONAL INJURY IF MISUSED IN SOUPERBLAST MODE TO PREVENT OVERHEATING DO NOT REPEAT SOUPERBLAST MODE FOR THE SAME HOT SOUP IF MORE HEAT IS REQUIRED PLACE THE CONTENTS IN A MICROWAVE SAFE CONTAINER AND CONTINUE HEATING TO DESIRED TEMPERATURE TO MAKE A NEW SOUP EMPTY OLD CONTENTS ADD NEW INGREDIENTS AND WAIT 1 FULL MINUTE BEFORE RETURNING THE VESSEL TO THE POWER BASE TO START A NEW SMART TECHNOLOGY CYCLE DO NOT REPEAT MORE THAN 2 CYCLES IN SOUPERBLAST MODE RESTING 1 MINUTE BETWEEN CYCLES DO NOT RUN THE NUTRIBULLET IN SOUPERBLAST MODE FOR MORE THAN 2 CYCLES CONSECUTIVELY WITHOUT ALLOWING THE NUTRIBULLET POWER BASE AND SOUPERBLAST ACCESSORIES COOL OFF FOR 3060 MIN TO PREVENT OVERHEATING AND ALLOW INGREDIENTS TO SETTLE BEFORE CONTINUING TO BLEND IF POWER BASE DOES NOT SHUT OFF AFTER ONE 1 7MINUTE INTERVAL DURING SOUPERBLAST MODE DEPRESS THE POWER BUTTON LOCATED 90 TO THE LEFT SIDE OF THE GBUTTON OR SIMPLY LIFT THE SOUPERBLAST PITCHER OFF OF THE POWER BASE ALLOW POWERBASE TO SHUT OFF COMPLETELY AFTER INITIAL INTERVAL AND WAIT FOR 34 MINUTES BETWEEN INTERVALS POWER BASE IS EQUIPPED WITH AN INTERNAL THERMAL BREAKER THAT SHUTS OFF THE POWER BASE WHEN THE UNIT OVERHEATS IF THE POWERBASE OVERHEATS AND SHUTS OFF UNPLUG THE POWER BASE OR PRESS THE POWER BUTTON LOCATED 90 TO THE LEFT OF THE GBUTTON AND LET IT COOL FOR AN HOUR OR MORE BEFORE ATTEMPTING TO USE IT AGAIN POWER BASE WILL RESET WHEN THE UNIT IS POWERED OFF AND THE THERMAL BREAKER HAS COOLED DOWN SUFFICIENTLY HEAT CAUTION DURING SOUPERBLAST MODE THE CONTENTS INSIDE CAN REACH UP TO ABOUT 70ºC 150ºF THROUGH THE FRICTION OF THE ROTATING BLADE KEEP HANDS AND OTHER EXPOSED SKIN AWAY FROM THE LID OPENING TO PREVENT POSSIBLE BURNS DURING SOUPERBLAST MODE DO NOT REMOVE THE LID DURING PROCESSING OF SOUPINGREDIENTS WILL BECOME HOT AND MAY SPLASH OUT AND CAUSE INJURY DO NOT TOUCH SOUPERBLAST PITCHER DIRECTLY WITH HANDS AFTER SOUPERBLAST MODE THE SOUPERBLAST PITCHER SURFACE BLADES AND COUPLING GEAR WILL BE HOT ALWAYS USE APPROPRIATE HEAT RESISTANT PADS ON THE HANDLE TO HOLD THE SOUPERBLAST PITCHER AND TO SUPPORT THE BOTTOM OF THE CONTAINER CAREFULLY OPEN SOUPERBLAST PITCHER LID AFTER SOUPERBLAST MODE AS ESCAPING STEAM AND MOISTURE MAY CAUSE SCALDING BURNS Always attach blade to SouperBlast Pitcher and hand tighten or use the blade remover to tighten the blade to prevent leakage prior to adding ingredients into the pitcher NEVER USE THE EXTRACTOR BLADE TO BLEND WITHOUT LIQUID AS DOING SO MAY DAMAGE THE BLADE Do not use the soup pitcher on the motor base without the black lid and clear vent top in place when running the NutriBullet Rx TO TURN THE NUTRIBULLET ON IN SOUPERBLAST mode using SMART Technology plug the power base into an electrical outlet Press the power button located 90 to the left side of the Gbutton The power button will glow BLUE signifying the power is on Next place the cup bladesidedown onto the power base This will activate the NutriBullet Rxs SMART TECHNOLOGY function causing the GButton at the front of the unit to glow GREEN Press the GREEN GButton down for 2 seconds until it glows RED This will indicate that SouperBlast mode has begun The unit will run in SouperBlast mode for about 7 minutes before automatically turning off Once off simply lift the SouperBlast Pitcher off of the Power Base The motor will run 3 cycles during the 7 minute programit will slow down twice through the cycle to allow the ingredients to settle for improved processing then it will increase again for the next part of the cycle This is a normal function of the NutriBullet Rx The contents inside can reach up to about 70ºC 150ºF through the friction of the rotating blade If you wish to process your soup for less than the programmed time you may simply lift off the SouperBlast Pitcher or press the power button located 90 to the left side of the Gbutton Always allow it to come to a complete stop prior to adding additional ingredients during the processing period Always depress the power button when not in use The BLUE light will stop glowing signifying the power is off
• Page 9 - English - : 8 9 SAFETY WARNINGS FOR EXTRACTING FOR SOUPS WARNING ONLY USE THE VENTED SOUPERBLAST PITCHER AND TWOPIECE LID WHILE OPERATING THE NUTRIBULLET Rx IN SOUPERBLAST MODE THE SOUPERBLAST PITCHER IS SPECIALLY VENTED TO RELEASE PRESSURE AS THE SOUP MIXTURE HEATS OTHER VESSELS ARE UNVENTED AND MAY RUPTURE AND CAUSE PERSONAL INJURY IF MISUSED IN SOUPERBLAST MODE TO PREVENT OVERHEATING DO NOT REPEAT SOUPERBLAST MODE FOR THE SAME HOT SOUP IF MORE HEAT IS REQUIRED PLACE THE CONTENTS IN A MICROWAVE SAFE CONTAINER AND CONTINUE HEATING TO DESIRED TEMPERATURE TO MAKE A NEW SOUP EMPTY OLD CONTENTS ADD NEW INGREDIENTS AND WAIT 1 FULL MINUTE BEFORE RETURNING THE VESSEL TO THE POWER BASE TO START A NEW SMART TECHNOLOGY CYCLE DO NOT REPEAT MORE THAN 2 CYCLES IN SOUPERBLAST MODE RESTING 1 MINUTE BETWEEN CYCLES DO NOT RUN THE NUTRIBULLET IN SOUPERBLAST MODE FOR MORE THAN 2 CYCLES CONSECUTIVELY WITHOUT ALLOWING THE NUTRIBULLET POWER BASE AND SOUPERBLAST ACCESSORIES COOL OFF FOR 3060 MIN TO PREVENT OVERHEATING AND ALLOW INGREDIENTS TO SETTLE BEFORE CONTINUING TO BLEND IF POWER BASE DOES NOT SHUT OFF AFTER ONE 1 7MINUTE INTERVAL DURING SOUPERBLAST MODE DEPRESS THE POWER BUTTON LOCATED 90 TO THE LEFT SIDE OF THE GBUTTON OR SIMPLY LIFT THE SOUPERBLAST PITCHER OFF OF THE POWER BASE ALLOW POWERBASE TO SHUT OFF COMPLETELY AFTER INITIAL INTERVAL AND WAIT FOR 34 MINUTES BETWEEN INTERVALS POWER BASE IS EQUIPPED WITH AN INTERNAL THERMAL BREAKER THAT SHUTS OFF THE POWER BASE WHEN THE UNIT OVERHEATS IF THE POWERBASE OVERHEATS AND SHUTS OFF UNPLUG THE POWER BASE OR PRESS THE POWER BUTTON LOCATED 90 TO THE LEFT OF THE GBUTTON AND LET IT COOL FOR AN HOUR OR MORE BEFORE ATTEMPTING TO USE IT AGAIN POWER BASE WILL RESET WHEN THE UNIT IS POWERED OFF AND THE THERMAL BREAKER HAS COOLED DOWN SUFFICIENTLY HEAT CAUTION DURING SOUPERBLAST MODE THE CONTENTS INSIDE CAN REACH UP TO ABOUT 70ºC 150ºF THROUGH THE FRICTION OF THE ROTATING BLADE KEEP HANDS AND OTHER EXPOSED SKIN AWAY FROM THE LID OPENING TO PREVENT POSSIBLE BURNS DURING SOUPERBLAST MODE DO NOT REMOVE THE LID DURING PROCESSING OF SOUPINGREDIENTS WILL BECOME HOT AND MAY SPLASH OUT AND CAUSE INJURY DO NOT TOUCH SOUPERBLAST PITCHER DIRECTLY WITH HANDS AFTER SOUPERBLAST MODE THE SOUPERBLAST PITCHER SURFACE BLADES AND COUPLING GEAR WILL BE HOT ALWAYS USE APPROPRIATE HEAT RESISTANT PADS ON THE HANDLE TO HOLD THE SOUPERBLAST PITCHER AND TO SUPPORT THE BOTTOM OF THE CONTAINER CAREFULLY OPEN SOUPERBLAST PITCHER LID AFTER SOUPERBLAST MODE AS ESCAPING STEAM AND MOISTURE MAY CAUSE SCALDING BURNS Always attach blade to SouperBlast Pitcher and hand tighten or use the blade remover to tighten the blade to prevent leakage prior to adding ingredients into the pitcher NEVER USE THE EXTRACTOR BLADE TO BLEND WITHOUT LIQUID AS DOING SO MAY DAMAGE THE BLADE Do not use the soup pitcher on the motor base without the black lid and clear vent top in place when running the NutriBullet Rx TO TURN THE NUTRIBULLET ON IN SOUPERBLAST mode using SMART Technology plug the power base into an electrical outlet Press the power button located 90 to the left side of the Gbutton The power button will glow BLUE signifying the power is on Next place the cup bladesidedown onto the power base This will activate the NutriBullet Rxs SMART TECHNOLOGY function causing the GButton at the front of the unit to glow GREEN Press the GREEN GButton down for 2 seconds until it glows RED This will indicate that SouperBlast mode has begun The unit will run in SouperBlast mode for about 7 minutes before automatically turning off Once off simply lift the SouperBlast Pitcher off of the Power Base The motor will run 3 cycles during the 7 minute programit will slow down twice through the cycle to allow the ingredients to settle for improved processing then it will increase again for the next part of the cycle This is a normal function of the NutriBullet Rx The contents inside can reach up to about 70ºC 150ºF through the friction of the rotating blade If you wish to process your soup for less than the programmed time you may simply lift off the SouperBlast Pitcher or press the power button located 90 to the left side of the Gbutton Always allow it to come to a complete stop prior to adding additional ingredients during the processing period Always depress the power button when not in use The BLUE light will stop glowing signifying the power is off
• Page 10 - English - : CLEANING SAFEGUARDS AFTER MAKING A NUTRIBLAST OR SOUPERBLAST THE BLADE MUST BE CLEANED IMMEDIATELY ALWAYS UNPLUG POWER BASE AND DEPRESS THE POWER BUTTON PRIOR TO CLEANING ASSEMBLING OR DISASSBMBLING NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN THE DISHWASHER WIPE OFF ANY DEBRIS INSIDE THE POWER BASE IMMEDIATELY TO KEEP IT IN GOOD WORKING ORDER DO NOT WASH THE BLADES IN THE DISHWASHER AS ELEVATED TEMPERATURES CAN DAMAGE GASKET SEALS THE NUTRIBULLET Rx CUPS CAN BE WASHED IN THE DISHWASHER AND SHOULD BE WASHED ON THE TOP RACK OF THE DISHWASHER USING THE NORMAL NOT SANITIZE CYCLE THE NUTRIBULLET Rx CUPS AND BLADES SHOULD NOT BE EMMERSED IN BOILING WATER FOR ANY REASON AS THIS WILL WARP PLASTIC AND DAMAGE GASKETS BLADES ARE SHARP USE CARE WHEN CLEANING BLADES TO AVOID INJURY RINSE BLADES IMMEDIATELY AFTER EACH USE TO PREVENT DEBRIS FROM DRYING AND STICKING TO BLADE COMPONENTS IF NECESSARY USE INCLUDED BRUSH TO LOOSEN ANY DEBRIS AROUND BLADES GASKETS AND BLADE HOUSING THREADS WITH CARE HANDWASH ONLY WITH MILD DISH SOAP AND WARM WATER NOT HOT DRY IMMEDIATELY FOR TOUGH DEBRIS FILL THE CUP ½ FULL WITH WARM NOT HOT MILD SOAPY WATER THEN SIMPLY TWIST ON THE BLADE POP IT ON THE BASE AND GIVE IT A RUN FOR 3045 SECONDS FOLLOW UP WITH A QUICK BRUSH WHEN WASHING BLADES DO NOT ATTEMPT TO REMOVE THE GASKET RING SIMPLY HAND WASH THE BLADES IN WARM MILD SOAPY WATER ATTEMPTED REMOVAL OF THE GASKET MAY PERMANENTLY DAMAGE THE BLADE CONFIGURATION AND CAUSE LEAKAGE STUBBORN CLEANUP If ingredients dry inside the NutriBullet Rx Cups or SouperBlast Pitcher make your cleanup a snap by filling the cup about 23 full with warm soapy water and screw on the Extractor Blade and if using the SouperBlast Pitcher put on lids Place the cup assembly on the NutriBullet Rx Power Base for about 2030 seconds That will loosen the stuck ingredients and with a light scrub and rinse youll be all done CLEANING THE NUTRIBULLET Rx POWER BASE For the most part the Power Base doesnt really get dirty but if you neglect to twist the blade on to the cup tightly liquids can leak out and get into the base and activator buttons Heres how to clean it up Step 1 The most important thing is to UNPLUG the Power Base before cleaning Step 2 Use a damp rag to wipe down the inside and outside of the Power Base NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN THE DISHWASHER Never put your hands or utensils near the moving blade and never use your hands or utensils to press the activator buttons down while the Power Base is plugged in HEAVY CLEANING Should the inside of the base become sticky due to spillage you may follow these additional cleaning instructions UNPLUG the Power Base and depress the power button BEFORE cleaning Place the Power Base on a dish towel to catch any liquid or debris Pour a scant 18 cup of a dilute solution of distilled vinegar and warm not hot water 1 part vinegar to 2 parts water in to the Power Base where the blade assembly would sit during normal use Immediately use a dish brush to dislodge any debris and wipe it out with a damp cloth The Power Base is constructed with a drain tube to drain any liquid debris safely through to the dish towel without damaging the inside components SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY If the power cord is damaged it must be replaced by the manufacturer its authorized service agent or similarly qualified persons in order to avoid a hazard FOOD PROCESSOR NAME NUTRIBULLET MODEL NB301 RATING 220240V 5060Hz 1700W MAX HOUSEHOLD USE ONLY MADE IN PRC
• Page 11 - English - : CLEANING SAFEGUARDS AFTER MAKING A NUTRIBLAST OR SOUPERBLAST THE BLADE MUST BE CLEANED IMMEDIATELY ALWAYS UNPLUG POWER BASE AND DEPRESS THE POWER BUTTON PRIOR TO CLEANING ASSEMBLING OR DISASSBMBLING NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN THE DISHWASHER WIPE OFF ANY DEBRIS INSIDE THE POWER BASE IMMEDIATELY TO KEEP IT IN GOOD WORKING ORDER DO NOT WASH THE BLADES IN THE DISHWASHER AS ELEVATED TEMPERATURES CAN DAMAGE GASKET SEALS THE NUTRIBULLET Rx CUPS CAN BE WASHED IN THE DISHWASHER AND SHOULD BE WASHED ON THE TOP RACK OF THE DISHWASHER USING THE NORMAL NOT SANITIZE CYCLE THE NUTRIBULLET Rx CUPS AND BLADES SHOULD NOT BE EMMERSED IN BOILING WATER FOR ANY REASON AS THIS WILL WARP PLASTIC AND DAMAGE GASKETS BLADES ARE SHARP USE CARE WHEN CLEANING BLADES TO AVOID INJURY RINSE BLADES IMMEDIATELY AFTER EACH USE TO PREVENT DEBRIS FROM DRYING AND STICKING TO BLADE COMPONENTS IF NECESSARY USE INCLUDED BRUSH TO LOOSEN ANY DEBRIS AROUND BLADES GASKETS AND BLADE HOUSING THREADS WITH CARE HANDWASH ONLY WITH MILD DISH SOAP AND WARM WATER NOT HOT DRY IMMEDIATELY FOR TOUGH DEBRIS FILL THE CUP ½ FULL WITH WARM NOT HOT MILD SOAPY WATER THEN SIMPLY TWIST ON THE BLADE POP IT ON THE BASE AND GIVE IT A RUN FOR 3045 SECONDS FOLLOW UP WITH A QUICK BRUSH WHEN WASHING BLADES DO NOT ATTEMPT TO REMOVE THE GASKET RING SIMPLY HAND WASH THE BLADES IN WARM MILD SOAPY WATER ATTEMPTED REMOVAL OF THE GASKET MAY PERMANENTLY DAMAGE THE BLADE CONFIGURATION AND CAUSE LEAKAGE STUBBORN CLEANUP If ingredients dry inside the NutriBullet Rx Cups or SouperBlast Pitcher make your cleanup a snap by filling the cup about 23 full with warm soapy water and screw on the Extractor Blade and if using the SouperBlast Pitcher put on lids Place the cup assembly on the NutriBullet Rx Power Base for about 2030 seconds That will loosen the stuck ingredients and with a light scrub and rinse youll be all done CLEANING THE NUTRIBULLET Rx POWER BASE For the most part the Power Base doesnt really get dirty but if you neglect to twist the blade on to the cup tightly liquids can leak out and get into the base and activator buttons Heres how to clean it up Step 1 The most important thing is to UNPLUG the Power Base before cleaning Step 2 Use a damp rag to wipe down the inside and outside of the Power Base NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN THE DISHWASHER Never put your hands or utensils near the moving blade and never use your hands or utensils to press the activator buttons down while the Power Base is plugged in HEAVY CLEANING Should the inside of the base become sticky due to spillage you may follow these additional cleaning instructions UNPLUG the Power Base and depress the power button BEFORE cleaning Place the Power Base on a dish towel to catch any liquid or debris Pour a scant 18 cup of a dilute solution of distilled vinegar and warm not hot water 1 part vinegar to 2 parts water in to the Power Base where the blade assembly would sit during normal use Immediately use a dish brush to dislodge any debris and wipe it out with a damp cloth The Power Base is constructed with a drain tube to drain any liquid debris safely through to the dish towel without damaging the inside components SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY If the power cord is damaged it must be replaced by the manufacturer its authorized service agent or similarly qualified persons in order to avoid a hazard FOOD PROCESSOR NAME NUTRIBULLET MODEL NB301 RATING 220240V 5060Hz 1700W MAX HOUSEHOLD USE ONLY MADE IN PRC
• Page 12 - English - : 1 Extractor Blade 12 13 1 Oversized Cup with 1 Pitcher Lid 1 Short Cup with 1 Comfort Lip Ring 1 SouperBlast Pitcher with 2piece Lid 1 Hightorque Power Base 1 User Guide 1 Recipe Book 1 Blade Cleaning Brush 1 Blade Remover WHAT YOU GET 1 Extractor Blade 1 Hightorque Power Base 1 Stayfresh Resealable Lid
• Page 13 - English - : 1 Extractor Blade 12 13 1 Oversized Cup with 1 Pitcher Lid 1 Short Cup with 1 Comfort Lip Ring 1 SouperBlast Pitcher with 2piece Lid 1 Hightorque Power Base 1 User Guide 1 Recipe Book 1 Blade Cleaning Brush 1 Blade Remover WHAT YOU GET 1 Extractor Blade 1 Hightorque Power Base 1 Stayfresh Resealable Lid
• Page 14 - English - : Add ingredients into one of the cups Fill with liquid up to the Max Line Then twist the Extractor Blade onto the cup and tighten by hand to make sure the vessel is sealed Plug the power base into an electrical outlet Press the power button located 90 to the left side of the Gbutton to turn the machine on The power button light will glow BLUE signifying power Next place the cup bladesidedown onto the power base This will activate the NutriBullet Rxs SMART Technology function causing the GButton at the front of the unit to glow GREEN and initiating the 1minute extraction cycle When the cycle has completed and the GREEN light has turned off turn off the unit by depressing the power button located 90 to the left side of the Gbutton The BLUE light will stop glowing signifying the power is off MAX LINE 14 15 HOW IT WORKS Do not run SouperBlast Mode with any of the blending cups Only use the vented SouperBlast Pitcher Read all safety instructions fi rst EXTRACTING FOR NUTRIBLAST RxS NOTE IF AT ANY TIME THE G BUTTON IS PUSHED FOR 2 SECONDS THE BUTTON WILL TURN RED AND INITIATE SOUPERBLAST MODE WHEN EXTRACTING OIL BASED OR STICKY FOODS REFER TO INSTRUCTIONS LISTED UNDER TAP TECHNIQUE ON PAGE 19 DO NOT TOUCH COUPLING GEAR DIRECTLY WITH HANDS AFTER NUTRIBLAST MODE THE COUPLING GEAR IN BLADE BASE AND POWER BASE WILL BE HOT TO TURN OFF THE MACHINE AT ANYTIME DURING THE NUTRIBLAST CYCLE G BUTTON WILL BE GREEN PRESS THE POWER BUTTON LOCATED 90 TO THE LEFT SIDE OF THE GBUTTON OR LIFT THE CUP OFF THE POWER BASE Note You can remove the cup at any time during the blending cycle by simply lifting the cup off of the Power Base If more extraction is required lift the cup off of the Power Base wait 15 seconds then return it back onto the Power Base to start another SMART Technology cycle Do not repeat more than 3 consecutive cycles resting 15 seconds between cycles If you press the green Gbutton for 2 seconds and the light turns RED you have switched in SouperBlast Mode Simply lift the cup off the Power Base at any time to exit this mode or press the power button located 90 to the left side of the Gbutton When the vessel is removed from the power base only the Gbutton light will turn off When the power off button is pressed the BLUE light will turn off and the blade will stop spinning Always press the power off button upon completion of processing POWER BUTTON
• Page 15 - English - : Add ingredients into one of the cups Fill with liquid up to the Max Line Then twist the Extractor Blade onto the cup and tighten by hand to make sure the vessel is sealed Plug the power base into an electrical outlet Press the power button located 90 to the left side of the Gbutton to turn the machine on The power button light will glow BLUE signifying power Next place the cup bladesidedown onto the power base This will activate the NutriBullet Rxs SMART Technology function causing the GButton at the front of the unit to glow GREEN and initiating the 1minute extraction cycle When the cycle has completed and the GREEN light has turned off turn off the unit by depressing the power button located 90 to the left side of the Gbutton The BLUE light will stop glowing signifying the power is off MAX LINE 14 15 HOW IT WORKS Do not run SouperBlast Mode with any of the blending cups Only use the vented SouperBlast Pitcher Read all safety instructions fi rst EXTRACTING FOR NUTRIBLAST RxS NOTE IF AT ANY TIME THE G BUTTON IS PUSHED FOR 2 SECONDS THE BUTTON WILL TURN RED AND INITIATE SOUPERBLAST MODE WHEN EXTRACTING OIL BASED OR STICKY FOODS REFER TO INSTRUCTIONS LISTED UNDER TAP TECHNIQUE ON PAGE 19 DO NOT TOUCH COUPLING GEAR DIRECTLY WITH HANDS AFTER NUTRIBLAST MODE THE COUPLING GEAR IN BLADE BASE AND POWER BASE WILL BE HOT TO TURN OFF THE MACHINE AT ANYTIME DURING THE NUTRIBLAST CYCLE G BUTTON WILL BE GREEN PRESS THE POWER BUTTON LOCATED 90 TO THE LEFT SIDE OF THE GBUTTON OR LIFT THE CUP OFF THE POWER BASE Note You can remove the cup at any time during the blending cycle by simply lifting the cup off of the Power Base If more extraction is required lift the cup off of the Power Base wait 15 seconds then return it back onto the Power Base to start another SMART Technology cycle Do not repeat more than 3 consecutive cycles resting 15 seconds between cycles If you press the green Gbutton for 2 seconds and the light turns RED you have switched in SouperBlast Mode Simply lift the cup off the Power Base at any time to exit this mode or press the power button located 90 to the left side of the Gbutton When the vessel is removed from the power base only the Gbutton light will turn off When the power off button is pressed the BLUE light will turn off and the blade will stop spinning Always press the power off button upon completion of processing POWER BUTTON
• Page 16 - English - : 16 17 POWER BUTTON EXTRACTING FOR SOUPERBLASTS Twist the Extractor Blade onto the SouperBlast Pitcher Add ingredients into the SouperBlast Pitcher and securely attach the vented 2piece lid SouperBlast Pitcher Lid Plug the power base into an electrical outlet Press the power button located 90 to the left side of the Gbutton to turn the machine on Next place the cup bladesidedown onto the power base This will activate the NutriBullet Rxs SMART Technology function causing the GButton at the front of the unit to glow GREEN Press the GREEN GButton down for 2 seconds until it glows RED This will indicate that SouperBlast Mode has begun The unit will run in SouperBlast Mode for about 7 minutes before automatically turning off causing the ingredients inside the SouperBlast Pitcher to heat up to about 70 degrees Celsius150 degrees Fahrenheit The unit is programmed to slow down twice during the 7minute cycle to allow ingredients to settle for improved processing This is normal Do not repeat SouperBlast Mode for the same hot soup If more heat is required place the contents in a microwavesafe container and continue heating to desired temperature To make a new soup empty old contents add new ingredients and wait 1 full minute before returning the vessel to the Power Base to start a new SMART Technology cycle Do not repeat more than 2 cycles in SouperBlast mode resting 1 minute between cycles After 2 consecutive cycles allow the NutriBullet Power Base and SouperBlast accessories to cool off for 3060 min Depress the power button upon completion WARNING AFTER SOUPERBLAST MODE THE SOUPERBLAST PITCHER SURFACE BLADES AND COUPLING GEAR WILL BE HOT DO NOT TOUCH DIRECTLY WITH HANDS ALWAYS USE HEAT RESISTANT PADS TO GRASP THE HANDLE AND TO SUPPORT THE BOTTOM OF THE SOUPERBLAST PITCHER IF YOU DESIRE SOUP TO BE HOTTER OR YOU WISH TO REHEAT SOUP TRANSFER FIRST TO AN APPROPRIATE MICROWAVE SAFE CONTAINER OR STOVE TOP POT AND HEAT SEPARATELYDO NOT REHEAT IN THE NUTRIBULLET Rx TO TURN OFF THE MACHINE AT ANYTIME DURING THE SOUPERBLAST CYCLE G BUTTON WILL BE RED PRESS THE POWER OFF BUTTON LOCATED 90 TO THE LEFT SIDE OF THE GBUTTON OR LIFT THE SOUPERBLAST PITCHER OFF THE POWER BASE
• Page 17 - English - : 16 17 POWER BUTTON EXTRACTING FOR SOUPERBLASTS Twist the Extractor Blade onto the SouperBlast Pitcher Add ingredients into the SouperBlast Pitcher and securely attach the vented 2piece lid SouperBlast Pitcher Lid Plug the power base into an electrical outlet Press the power button located 90 to the left side of the Gbutton to turn the machine on Next place the cup bladesidedown onto the power base This will activate the NutriBullet Rxs SMART Technology function causing the GButton at the front of the unit to glow GREEN Press the GREEN GButton down for 2 seconds until it glows RED This will indicate that SouperBlast Mode has begun The unit will run in SouperBlast Mode for about 7 minutes before automatically turning off causing the ingredients inside the SouperBlast Pitcher to heat up to about 70 degrees Celsius150 degrees Fahrenheit The unit is programmed to slow down twice during the 7minute cycle to allow ingredients to settle for improved processing This is normal Do not repeat SouperBlast Mode for the same hot soup If more heat is required place the contents in a microwavesafe container and continue heating to desired temperature To make a new soup empty old contents add new ingredients and wait 1 full minute before returning the vessel to the Power Base to start a new SMART Technology cycle Do not repeat more than 2 cycles in SouperBlast mode resting 1 minute between cycles After 2 consecutive cycles allow the NutriBullet Power Base and SouperBlast accessories to cool off for 3060 min Depress the power button upon completion WARNING AFTER SOUPERBLAST MODE THE SOUPERBLAST PITCHER SURFACE BLADES AND COUPLING GEAR WILL BE HOT DO NOT TOUCH DIRECTLY WITH HANDS ALWAYS USE HEAT RESISTANT PADS TO GRASP THE HANDLE AND TO SUPPORT THE BOTTOM OF THE SOUPERBLAST PITCHER IF YOU DESIRE SOUP TO BE HOTTER OR YOU WISH TO REHEAT SOUP TRANSFER FIRST TO AN APPROPRIATE MICROWAVE SAFE CONTAINER OR STOVE TOP POT AND HEAT SEPARATELYDO NOT REHEAT IN THE NUTRIBULLET Rx TO TURN OFF THE MACHINE AT ANYTIME DURING THE SOUPERBLAST CYCLE G BUTTON WILL BE RED PRESS THE POWER OFF BUTTON LOCATED 90 TO THE LEFT SIDE OF THE GBUTTON OR LIFT THE SOUPERBLAST PITCHER OFF THE POWER BASE
• Page 18 - English - : 18 19 HOW IT WORKS SHAKE TECHNIQUE Sometimes if you over fill the cups with ingredients or dont put enough water the results can increase the density of the mixture This makes it hard for the ingredients toward the top of the cup to make it down to the blade If some of your ingredients are having a hard time making it down to the blade simply use the Shake technique Remove the cup and blade assembly from the Power Base With the cup and blade assembly in hand shake it like a cocktail shaker Then put it back on the Power Base TAP TECHNIQUE For really stubborn ingredients that are clinging to the side of the cup instead of being recirculated into the cutting zone simply use the Tap technique Take the cup and blade assembly off the Power Base and Tap the cup and blade assembly on the counter to force the ingredients down into the blades Place the cup and blade assembly onto the Power Base and finish processing WHEN MAKING NUT BUTTERS OR OILBASED FOODS DUE TO THE CONSISTENCY THE FOOD WILL PROCESS AND THEN STICK TO THE SIDES OF THE CUP PROCESS IN 30 SECOND INCREMENTS BY SIMPLY LIFTING THE CUP OFF THE POWER BASE BETWEEN INTERVALS BETWEEN CYCLES USE A COMBINATION OF THE TAP METHOD DESCRIBED ABOVE AND OPEN CUP AS NEEDED TO SCRAPE DOWN THE INGREDIENTS TO THE CENTER OF THE CUP BEFORE CONTINUING TO PROCESS IN 30 SECOND INCREMENTS ALLOW MACHINE TO COOL DOWN FOR 10 MIN AFTER 45 CYCLES TO PREVENT OVERHEATING AND DAMAGING THE UNIT
• Page 19 - English - : 18 19 HOW IT WORKS SHAKE TECHNIQUE Sometimes if you over fill the cups with ingredients or dont put enough water the results can increase the density of the mixture This makes it hard for the ingredients toward the top of the cup to make it down to the blade If some of your ingredients are having a hard time making it down to the blade simply use the Shake technique Remove the cup and blade assembly from the Power Base With the cup and blade assembly in hand shake it like a cocktail shaker Then put it back on the Power Base TAP TECHNIQUE For really stubborn ingredients that are clinging to the side of the cup instead of being recirculated into the cutting zone simply use the Tap technique Take the cup and blade assembly off the Power Base and Tap the cup and blade assembly on the counter to force the ingredients down into the blades Place the cup and blade assembly onto the Power Base and finish processing WHEN MAKING NUT BUTTERS OR OILBASED FOODS DUE TO THE CONSISTENCY THE FOOD WILL PROCESS AND THEN STICK TO THE SIDES OF THE CUP PROCESS IN 30 SECOND INCREMENTS BY SIMPLY LIFTING THE CUP OFF THE POWER BASE BETWEEN INTERVALS BETWEEN CYCLES USE A COMBINATION OF THE TAP METHOD DESCRIBED ABOVE AND OPEN CUP AS NEEDED TO SCRAPE DOWN THE INGREDIENTS TO THE CENTER OF THE CUP BEFORE CONTINUING TO PROCESS IN 30 SECOND INCREMENTS ALLOW MACHINE TO COOL DOWN FOR 10 MIN AFTER 45 CYCLES TO PREVENT OVERHEATING AND DAMAGING THE UNIT
• Page 20 - English - : 20 21 CLEANING WARNING ALWAYS UNPLUG THE NUTRIBULLET AND DEPRESS THE POWER BUTTON WHEN CLEANING OR ASSEMBLING Washing the NUTRIBULLET Rx Cleaning the NUTRIBULLET Rx is so easy simply place any of the pieces except for the Power Base and blade holder on the top shelf of the dishwasher or hand wash with warm soapy water and rinse STUBBORN CLEANUP If ingredients dry inside the NutriBullet Rx Cups or SouperBlast Pitcher make your cleanup a snap by filling the cup about 23 full with warm soapy water and screw on the Extractor Blade and if using the SouperBlast Pitcher put on lids Place the cup assembly on the NutriBullet Rx Power Base for about 2030 seconds That will loosen the stuck ingredients and with a light scrub and rinse youll be all done CLEANING THE NUTRIBULLET POWER BASE For the most part the Power Base doesnt really get dirty but if you neglect to twist the blade on to the cup tightly liquids can leak out and get into the base and activator buttons Heres how to clean it up Step 1 The most important thing is to depress the power button and UNPLUG the Power Base before Step 2 Use a damp rag to wipe down the inside and outside of the Power Base NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN THE DISHWASHER Never put your hands or utensils near the moving blade and never use your hands or utensils to press the activator buttons down while the Power Base is plugged in CLEANING SAFEGUARDS AFTER MAKING A NUTRIBLAST OR SOUPERBLAST THE BLADE MUST BE CLEANED IMMEDIATELY ALWAYS UNPLUG POWER BASE AND DEPRESS THE THE POWER BUTTON PRIOR TO CLEANING ASSEMBLING OR DISASSBMBLING NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN THE DISHWASHER WIPE OFF ANY DEBRIS INSIDE THE POWER BASE IMMEDIATELY TO KEEP IT IN GOOD WORKING ORDER DO NOT WASH THE BLADES IN THE DISHWASHER AS ELEVATED TEMPERATURES CAN DAMAGE GASKET SEALS THE NUTRIBULLET Rx CUPS CAN BE WASHED IN THE DISHWASHER AND SHOULD BE WASHED ON THE TOP RACK OF THE DISHWASHER USING THE NORMAL NOT SANITIZE CYCLE THE NUTRIBULLET Rx CUPS AND BLADES SHOULD NOT BE EMERSED IN BOILING WATER FOR ANY REASON AS THIS WILL WARP PLASTIC AND DAMAGE GASKETS BLADES ARE SHARP USE CARE WHEN CLEANING BLADES TO AVOID INJURY RINSE BLADES IMMEDIATELY AFTER EACH USE TO PREVENT DEBRIS FROM DRYING AND STICKING TO BLADE COMPONENTS IF NECESSARY USE INCLUDED BRUSH TO LOOSEN AND DEBRIS AROUND BLADES GASKETS AND BLADE HOUSING THREADS WITH CARE HANDWASH ONLY WITH MILD DISH SOAP AND WARM WATER NOT HOT DRY IMMEDIATELY FOR TOUGH DEBRIS FILL THE CUP ½ FULL WITH WARM NOT HOT MILD SOAPY WATER THEN SIMPLY TWIST ON THE BLADE POP IT ON THE BASE AND GIVE IT A RUN FOR 3045 SECONDS FOLLOW UP WITH A QUICK BRUSH WHEN WASHING BLADES DO NOT ATTEMPT TO REMOVE THE GASKET RING SIMPLY HAND WASH THE BLADES IN WARM MILD SOAPY WATER ATTEMPTED REMOVAL OF THE GASKET MAY PERMANENTLY DAMAGE THE BLADE CONFIGURATION AND CAUSE LEAKAGE
• Page 21 - English - : 20 21 CLEANING WARNING ALWAYS UNPLUG THE NUTRIBULLET AND DEPRESS THE POWER BUTTON WHEN CLEANING OR ASSEMBLING Washing the NUTRIBULLET Rx Cleaning the NUTRIBULLET Rx is so easy simply place any of the pieces except for the Power Base and blade holder on the top shelf of the dishwasher or hand wash with warm soapy water and rinse STUBBORN CLEANUP If ingredients dry inside the NutriBullet Rx Cups or SouperBlast Pitcher make your cleanup a snap by filling the cup about 23 full with warm soapy water and screw on the Extractor Blade and if using the SouperBlast Pitcher put on lids Place the cup assembly on the NutriBullet Rx Power Base for about 2030 seconds That will loosen the stuck ingredients and with a light scrub and rinse youll be all done CLEANING THE NUTRIBULLET POWER BASE For the most part the Power Base doesnt really get dirty but if you neglect to twist the blade on to the cup tightly liquids can leak out and get into the base and activator buttons Heres how to clean it up Step 1 The most important thing is to depress the power button and UNPLUG the Power Base before Step 2 Use a damp rag to wipe down the inside and outside of the Power Base NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN THE DISHWASHER Never put your hands or utensils near the moving blade and never use your hands or utensils to press the activator buttons down while the Power Base is plugged in CLEANING SAFEGUARDS AFTER MAKING A NUTRIBLAST OR SOUPERBLAST THE BLADE MUST BE CLEANED IMMEDIATELY ALWAYS UNPLUG POWER BASE AND DEPRESS THE THE POWER BUTTON PRIOR TO CLEANING ASSEMBLING OR DISASSBMBLING NEVER SUBMERGE THE POWER BASE IN WATER OR PLACE IT IN THE DISHWASHER WIPE OFF ANY DEBRIS INSIDE THE POWER BASE IMMEDIATELY TO KEEP IT IN GOOD WORKING ORDER DO NOT WASH THE BLADES IN THE DISHWASHER AS ELEVATED TEMPERATURES CAN DAMAGE GASKET SEALS THE NUTRIBULLET Rx CUPS CAN BE WASHED IN THE DISHWASHER AND SHOULD BE WASHED ON THE TOP RACK OF THE DISHWASHER USING THE NORMAL NOT SANITIZE CYCLE THE NUTRIBULLET Rx CUPS AND BLADES SHOULD NOT BE EMERSED IN BOILING WATER FOR ANY REASON AS THIS WILL WARP PLASTIC AND DAMAGE GASKETS BLADES ARE SHARP USE CARE WHEN CLEANING BLADES TO AVOID INJURY RINSE BLADES IMMEDIATELY AFTER EACH USE TO PREVENT DEBRIS FROM DRYING AND STICKING TO BLADE COMPONENTS IF NECESSARY USE INCLUDED BRUSH TO LOOSEN AND DEBRIS AROUND BLADES GASKETS AND BLADE HOUSING THREADS WITH CARE HANDWASH ONLY WITH MILD DISH SOAP AND WARM WATER NOT HOT DRY IMMEDIATELY FOR TOUGH DEBRIS FILL THE CUP ½ FULL WITH WARM NOT HOT MILD SOAPY WATER THEN SIMPLY TWIST ON THE BLADE POP IT ON THE BASE AND GIVE IT A RUN FOR 3045 SECONDS FOLLOW UP WITH A QUICK BRUSH WHEN WASHING BLADES DO NOT ATTEMPT TO REMOVE THE GASKET RING SIMPLY HAND WASH THE BLADES IN WARM MILD SOAPY WATER ATTEMPTED REMOVAL OF THE GASKET MAY PERMANENTLY DAMAGE THE BLADE CONFIGURATION AND CAUSE LEAKAGE
• Page 22 - English - : 4 EASY STEPS Fill the cup with 50 leafy greens 50 fruit Fill only up to the MAX line with water add ice if you want Add 18 to 14 nuts andor seeds if desired Twist on the NUTRIBULLET Rx blade and blend until smooth HOW TO BUILD A NUTRIBLAST Collard Greens Kale Romaine Spinach Spring Greens Swiss Chard Apple Avocado Banana Blackberry Blueberry Cantaloupe Cranberry Fig Almonds Cashews Walnuts Nuts Seeds Super Chargers Green Grapes Guava Honeydew Kiwi Mango Nectarine Orange Papaya Chia Seeds Flax Seeds Hemp Seeds Pumpkin Seeds Sesame Seeds Sunfl ower Seeds Goji Berries Acai Berries Peach Pear Pineapple Plum Raspberries Red Grapes Strawberry Watermelon LEAFY GREENS 50 Choose one from the following list of leafy greens or mix and match Fill the Oversized Cup up to 50 with leafy greens Work up to 2 full cups 2 handfuls of leafy greens per Blast FRUITS 50 Choose as many fruits as you want to equal 50 of your NUTRIBLAST Rx BOOSTS 14 CUP The following ingredients are an important part of your NUTRIBLAST Rx adding additional fi ber and nutrition to every sip Add 18 to ¼ cup to any Blast MAX 50 leafy greens 2 cups 1 serving 50 fruit as many varieties as possible Add boost Add water to MAX line WARNING BAD SEEDS While NUTRITION EXTRACTION can be amazingly benefi cial not all fruit seeds and rinds are created equal The following seeds and pits contain a chemical that releases cyanide into the body when ingested DO NOT USE the following seeds and pits in the NUTRIBULLET Rx Apple Seeds Apricot Pits Cherry Pits Plum Pits Peach Pits NOTE You must add liquid up to the Max line when blending with the Extractor Blade for proper extraction to achieve the best taste and texture results with your NUTRIBULLET Rx and to prevent damage to the blade Add enough liquid to cover ingredients twist on the blade and blend A few of our favorite liquids are water coconut water and unsweetened almond milk TIP We recommend using frozen fruits such as berries or bananas if you desire a frosty NUTRIBLAST NOTE YOU MUST ALWAYS ADD A LIQUID BEFORE YOU BLEND A NUTRIBLAST DONT OVERFILL YOUR CUP MAKE SURE YOUR INGREDIENTS AND LIQUID REACH NO HIGHER THAN THE MAX LINE NUTRIBLAST Rx
• Page 23 - English - : 4 EASY STEPS Fill the cup with 50 leafy greens 50 fruit Fill only up to the MAX line with water add ice if you want Add 18 to 14 nuts andor seeds if desired Twist on the NUTRIBULLET Rx blade and blend until smooth HOW TO BUILD A NUTRIBLAST Collard Greens Kale Romaine Spinach Spring Greens Swiss Chard Apple Avocado Banana Blackberry Blueberry Cantaloupe Cranberry Fig Almonds Cashews Walnuts Nuts Seeds Super Chargers Green Grapes Guava Honeydew Kiwi Mango Nectarine Orange Papaya Chia Seeds Flax Seeds Hemp Seeds Pumpkin Seeds Sesame Seeds Sunfl ower Seeds Goji Berries Acai Berries Peach Pear Pineapple Plum Raspberries Red Grapes Strawberry Watermelon LEAFY GREENS 50 Choose one from the following list of leafy greens or mix and match Fill the Oversized Cup up to 50 with leafy greens Work up to 2 full cups 2 handfuls of leafy greens per Blast FRUITS 50 Choose as many fruits as you want to equal 50 of your NUTRIBLAST Rx BOOSTS 14 CUP The following ingredients are an important part of your NUTRIBLAST Rx adding additional fi ber and nutrition to every sip Add 18 to ¼ cup to any Blast MAX 50 leafy greens 2 cups 1 serving 50 fruit as many varieties as possible Add boost Add water to MAX line WARNING BAD SEEDS While NUTRITION EXTRACTION can be amazingly benefi cial not all fruit seeds and rinds are created equal The following seeds and pits contain a chemical that releases cyanide into the body when ingested DO NOT USE the following seeds and pits in the NUTRIBULLET Rx Apple Seeds Apricot Pits Cherry Pits Plum Pits Peach Pits NOTE You must add liquid up to the Max line when blending with the Extractor Blade for proper extraction to achieve the best taste and texture results with your NUTRIBULLET Rx and to prevent damage to the blade Add enough liquid to cover ingredients twist on the blade and blend A few of our favorite liquids are water coconut water and unsweetened almond milk TIP We recommend using frozen fruits such as berries or bananas if you desire a frosty NUTRIBLAST NOTE YOU MUST ALWAYS ADD A LIQUID BEFORE YOU BLEND A NUTRIBLAST DONT OVERFILL YOUR CUP MAKE SURE YOUR INGREDIENTS AND LIQUID REACH NO HIGHER THAN THE MAX LINE NUTRIBLAST Rx
• Page 24 - English - : 24 25 If your product becomes defective due to faulty material or workmanship within a period of 1 year from the date of purchase we warrant to do the following For New Zealand Consumers We will replace the product with a new product free of charge or repair the product at our cost at our discretion For Australian Consumers Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure Your warranty is subject to the following conditions DO NOT operate the appliance with a damaged plug or cord or if the unit has been dropped damaged or dropped in water To avoid the risk of electric shock do not disassemble or attempt to repair the appliance on your own If the supply cord is damaged it must be replaced by a qualied electrician in order to avoid a hazard Incorrect reassembly or repair can cause a risk of electric shock or injury to persons when the appliance is used The item has not been misused abused neglected altered modied or repaired by anyone The item has been subjected to fair wear and tear The item has not been used for trade professional or hire purposes The item has not sustained damage through foreign objects substances or accident Your warranty does not cover Components that are subject to natural wear and tear caused by normal use in accordance with operating instructions Unauthorisedimproper maintenancehandling or overload is excluded from this warranty For guarantee claims you will need to submit a proof of purchase in the form of a valid receipt that displays date and place of purchase This warranty does not replace but is in addition to your statutory rights This warranty does not apply to accessories supplied with the item This warranty applies only to the original purchaser and may not be transferred Replacement items will be covered by the limited warranty for the balance of the warranty period from the date of the original purchase Please note Only the defective product or parts returned to place of purchase will be replaced under this warranty ONE 1 YEAR LIMITED REPLACEMENT WARRANTY STATEMENT NOTES
• Page 25 - English - : 24 25 If your product becomes defective due to faulty material or workmanship within a period of 1 year from the date of purchase we warrant to do the following For New Zealand Consumers We will replace the product with a new product free of charge or repair the product at our cost at our discretion For Australian Consumers Our goods come with guarantees that cannot be excluded under the Australian Consumer Law You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure Your warranty is subject to the following conditions DO NOT operate the appliance with a damaged plug or cord or if the unit has been dropped damaged or dropped in water To avoid the risk of electric shock do not disassemble or attempt to repair the appliance on your own If the supply cord is damaged it must be replaced by a qualied electrician in order to avoid a hazard Incorrect reassembly or repair can cause a risk of electric shock or injury to persons when the appliance is used The item has not been misused abused neglected altered modied or repaired by anyone The item has been subjected to fair wear and tear The item has not been used for trade professional or hire purposes The item has not sustained damage through foreign objects substances or accident Your warranty does not cover Components that are subject to natural wear and tear caused by normal use in accordance with operating instructions Unauthorisedimproper maintenancehandling or overload is excluded from this warranty For guarantee claims you will need to submit a proof of purchase in the form of a valid receipt that displays date and place of purchase This warranty does not replace but is in addition to your statutory rights This warranty does not apply to accessories supplied with the item This warranty applies only to the original purchaser and may not be transferred Replacement items will be covered by the limited warranty for the balance of the warranty period from the date of the original purchase Please note Only the defective product or parts returned to place of purchase will be replaced under this warranty ONE 1 YEAR LIMITED REPLACEMENT WARRANTY STATEMENT NOTES
• Page 28 - English - : Transform your health with the most nutrient dense nutrition available At NutriBullet our motto has alwyas been its not what you eatits what you absorb Now with the NUTRIBULLET Rx you have the ability to extract foods into the most bioavailable state possible using the most revolutionary technology available The NUTRIBULLET Rx is the result of years of research and development using the best engineers top nutritionists top doctors and leading laboratories to create the best machine of its kind anywhere in the world The power speed heating capabilities and unique design of the NUTRIBULLET Rx make it easier than ever to maximize your daily intake and absorption of vegetables fruits nuts seeds and other superfoodsthe very foods that have been scientifically proven to reduce mortality when consumed and absorbed in abundance Join the millions of NutriBullet users who have transformed their health with the power of extracted nutrition aka natures prescription to look and feel better than they ever thought possible NUTRIBULLET is a registered trademark of HOMELAND HOUSEWARES LLC Copyright 2015 NUTRIBULLET LLC LOS ANGELES CA 90025 USA ALL RIGHTS RESERVED MADE IN CHINA NATURES PRESCRIPTION