User guide.
32
capabilities, or lack of experience and
knowledge, unless they are closely
supervised and instructed concerning
the use of the appliance by a person
responsible for their safety.
NEVER LEAVE THE NUTRIBULLET
®
UNATTENDED WHILE IT IS IN USE.
• Do not place or operate the nutribullet
®
on uneven or unstable surfaces.
• Do not place any nutribullet
®
part or
accessory in a microwave, conventional
oven, air fryer, or stovetop pot, or
immerse in boiling water, as this will
damage the part.
• Do not place or operate your nutribullet
®
on or near a hot gas or electric burner,
or in a heated oven.
• The risk of fi re, shock, or damage
to nutribullet
®
during cleaning can
be reduced by taking the following
precautions:
- Turn o your device and unplug it
before cleaning.
- Only clean the exterior of the Motor
Base with a clean dry cloth.
• To protect again the risk of electrical
shock, DO NOT immerse the Motor Base
in water or other liquid.
WARNING! NEVER WASH
YOUR NUTRIBULLET
®
PARTS
OR ACCESSORIES USING THE
SANITISE OR HEAT CYCLE OF YOUR
DISHWASHER. DOING SO CAN WARP
THE PART, WHICH CAN CREATE
HAZARDOUS CONDITIONS DURING
USE THAT MAY RESULT IN BODILY
INJURY OR PROPERTY DAMAGE.
• NEVER place any nutribullet
®
parts or
accessories in the freezer. Do not use
nutribullet
®
parts and accessories as
storage containers in the freezer.
• Never attempt to defeat any safety
interlock mechanisms on the
appliance.
• Remove and safely discard any
packaging material or promotional
labels before using the appliance for
the fi rst time.
• Do not operate your nutribullet
®
if
any of the parts and accessories are
or appear to be damaged in any
Important safeguards.
When operating your nutribullet
®
device, remember:
SAFETY COMES FIRST. WHEN USING ANY ELECTRICAL APPLIANCE. BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE OBSERVED, INCLUDING THE FOLLOWING:
WARNING! To avoid the risk of serious injury, death, property damage, or
damage to your device, carefully read all instructions before operating your
nutribullet
®
device. When using any electrical appliance, basic safety
precautions should always be observed, including the important information
in this User Guide.
If you let anyone else use your nutribullet
®
, make sure that they understand the health
and safety information in this User Guide, as well as any additional safety or usage
instructions provided. Each person using a device should carefully read the User
Guide in its entirety to become familiar with the safe operation of the unit.
!
Save these instructions!
FOR HOUSEHOLD USE ONLY
PERSONAL SAFETY:
Failure to follow all instructions regarding
the use of your nutribullet
®
device may
result in serious personal injury, death,
or property damage. Be aware of
possible hazards when using or storing
your nutribullet
®
.
WARNING! NEVER BLEND FOR
LONGER THAN ONE MINUTE. DO
NOT RUN CONSECUTIVE BLENDING
CYCLES THAT EXCEED ONE
MINUTE TOTAL.
The friction created by the blending
process builds heat inside the Cup.
Blending continuously for more than
one minute increases the risk of
pressurisation. Consecutive blending
cycles that exceed one minute total
may over-pressurise the Cup, causing
the Lid to open forcefully, or the Cup
and Motor Base, Blade, and Lid to
separate from the Cup. This could
expel hot ingredients and cause
exposure to the blade, potentially
resulting in bodily injury (including
burns) and/or property damage.
• Do not use the nutribullet
®
for
anything other than its intended
purpose.
• Do not open the Lid or remove the
Motor Base, Blade, and Lid until the
blades have come to a complete
stop. Blades can still activate when
connected to the Motor Base and Lid
is open.
• WARNING! REMOVE ALL UTENSILS
AND NON-FOOD ITEMS FROM
THE PITCHER BEFORE OPERATING
TO PREVENT BODILY INJURY,
OR DAMAGE TO THE BLADE OR
PITCHER.
• Do not leave or put non-food items
in any of the attachments when
blending. Doing so may damage the
unit or crack or shatter the attachment,
resulting in bodily injury or property
damage.
• Close supervision is necessary when
any appliance is used by or near
children to ensure they do not play
with the appliance. Keep cord out of
reach of children.
• This appliance is not intended for use
by persons (including children) with
reduced physical, sensory, or mental
manner that may impair proper
function or create a safety hazard.
If you suspect your nutribullet
®
parts and/or accessories may be
damaged, contact Customer Service
for assistance at AU: 1300 285 538 /
NZ: 0800 232 633.
• Do not use parts, accessories
or attachments from other
manufacturers, di erent models
of nutribullet
®
or magic bullet
®
products, or canning jars. Use of
parts, accessories or attachments
NOT specifi cally designed for your
particular nutribullet
®
device may
damage your unit or cause serious
bodily injury, fi re, or electric shock.
– Use only genuine nutribullet
®
attachments/accessories
specifi cally designed for your
nutribullet
®
device. Aftermarket
parts are not made to nutribullet
®
specifi cations and may damage
your unit or cause serious injury.
• DO NOT USE OUTDOORS.
• ALWAYS UNPLUG YOUR
NUTRIBULLET
®
WHEN NOT IN USE.
• To unplug, grasp the plug and pull
from the outlet. Never pull from the
power cord.
• Always POWER OFF and UNPLUG
the unit and wait until the Blade
comes to a complete stop before
assembling, disassembling,
changing accessories, or cleaning.
USING THE BLENDING
PITCHER:
WARNING! ONLY USE THE
BLENDING PITCHER WITH
THE VENTED PITCHER LID
TO BLEND HOT, WARM, OR
CARBONATED INGREDIENTS.
.
• ALWAYS a x the Vented Pitcher
Lid to the Blending Pitcher with
the spout down and closed before
blending to prevent ingredients from
splashing or hot ingredients from
splattering, which may cause burns,
bodily injuries, or property damage.
PITCHER
PITCHER
54
• After blending hot ingredients
or liquids, exercise caution when
opening the Pitcher Lid, and be
mindful of escaping hot steam or
splattering hot ingredients.
• Do not overfill the Blending Pitcher
beyond the MAX line.
• Do not use the Blending Pitcher if you
detect cracking, cloudiness, or other
damage. Visit bulletbrands.com.
au / bulletbrands.co.nz or contact
Customer Service to purchase a new
Blending Pitcher.
WARNING! TO INCORPORATE
INGREDIENTS DURING BLENDING,
CAREFULLY OPEN THE LID
CAP FROM THE PITCHER LID
AND GENTLY POUR OR DROP
INGREDIENTS INTO THE MIXTURE.
BE ESPECIALLY MINDFUL WHEN
ADDING TO HOT INGREDIENTS AND
LIQUIDS, AS ESCAPING STEAM OR
SPLATTERS MAY PRESENT A RISK
OF INJURY.
• When using manual speeds, start
blending on the LOW setting and,
once ingredients are integrated,
adjust the speed as needed.
BLENDER PITCHER SAFETY:
Proper Blending Pitcher use is
important for the safe operation of your
nutribullet
®
. Using the Blending Pitcher
inconsistent with these instructions may
result in bodily injury, property damage,
or damage to your unit.
• Only operate the Blending Pitcher
with the Pitcher Lid securely locked in
place and the spout closed.
• Before blending, check that the vent
slots on the Pitcher Lid are clear and
unobstructed. Clogged or obstructed
vent slots will pressurise the contents,
which can cause the release of hot
steam or splattered ingredients upon
opening.
• For recipes that require certain
ingredients to be incorporated
during blending, first add the base
ingredients, then attach the Pitcher
Lid and begin blending. Once the
ingredients are mixed well, twist
open the Vented Lid Cap and
carefully pour or drop ingredients
into the blended mixture. If the
blended mixture is hot or warm, use
caution and open the Vented Lid Cap
slowly, being mindful of escaping
hot steam or the splattering of
hot ingredients. Always reinstall
the Vented Lid Cap after adding
ingredients.
• NEVER place hands or use utensils
such as spatulas, spoons, or other
tools that may make contact with the
spinning blades while in operation.
Doing so can damage the unit,
shatter the Blending Pitcher, or
cause severe bodily injury or
property damage.
• ONLY USE THE TAMPER PROVIDED
with your nutribullet
®
through the
cover opening to push ingredients
closer to the Blade. NEVER use the
Tamper without the Pitcher Lid in
place. The Tamper is specifically
designed to avoid contact with the
Blade through the Pitcher Lid. A
scraper may be used, but only when
the blender is powered o and the
blades are at a complete stop.
GENERAL BLADE SAFETY:
WARNING! BLADES ARE SHARP!
HANDLE WITH CARE TO AVOID
BODILY INJURY. NON-FOOD
ITEMS OR HARD INGREDIENTS
MAY DAMAGE THE BLADES.
ROUTINELY INSPECT THE BLADES
AND DISCONTINUE USE IF THE
BLADES ARE DAMAGED OR DO
NOT FREELY ROTATE. CONTINUED
USE WITH DAMAGED BLADES OR
USE INCONSISTENT WITH THESE
INSTRUCTIONS MAY RESULT
IN BODILY INJURY, PROPERTY
DAMAGE, OR DAMAGE TO
YOUR UNIT.
NEVER STORE THE UNIT WITH THE
BLADE EXPOSED. ALWAYS COVER
THE BLADE WITH THE PITCHER
LID. EXPOSED BLADES PRESENT A
LACERATION HAZARD THAT MAY
CAUSE SEVERE PERSONAL INJURY.
• Always POWER OFF and UNPLUG
the unit and wait until the Blade
comes to a complete stop before
assembling, disassembling,
changing accessories, or cleaning.
• If a leak occurs, power o or unplug
the unit and allow the motor to come
to a complete stop before removing.
Instructions on how to clean up a
major spill on next column on page 5.
• DO NOT crush ice. Your nutribullet
®
is not intended to be used as an ice
crusher, which may shatter the
Pitcher, causing injury or damage.
Always use sucient liquids when
blending.
• Do not overload the Pitcher as
this may prevent the blades
from spinning.
• Do not attempt to grind dry
ingredients such as grains, cereal,
or coee, as this may overheat the
motor and/or damage the blades.
• AVOID CONTACT WITH MOVING
PARTS! Keep hands and utensils
out of and away from the Blade to
reduce the risk of severe personal
injury or damage to the unit.
• NEVER place the Extractor Blade or
other accessory parts on the bottom
rack of the dishwasher or use the
heat/sanitise cycle while cleaning
the components in the dishwasher.
• Periodically inspect your Blade. If
the blades do not rotate freely or are
damaged, immediately discontinue
use and contact Customer Service.
• FOR OPTIMAL PERFORMANCE,
WE RECOMMEND REPLACING THE
BLADE EVERY 6 MONTHS, OR AS
NEEDED, DEPENDING ON USE.
• Use of incompatible parts or
aftermarket parts may result in
damage to your nutribullet
®
unit
or present safety hazards that
may cause personal injury or
property damage. When ordering
replacement parts, always use
genuine nutribullet
®
parts and
accessories from bulletbrands.
com.au / bulletbrands.co.nz or by
contacting Customer Service at AU:
1300 285 538 / NZ: 0800 232 63.
PRODUCT SAFETY:
• DO NOT attempt to disengage
the Pitcher while the blade is still
moving.
• If you notice leakage, DO NOT
attempt to remove the Pitcher.
Immediately unplug the unit and
allow the blades to come to a
complete stop before removing the
Pitcher from the Motor Base.
ELECTRICAL SAFETY:
Modification, improper use, and
failure to follow the instructions for
proper setup, use, and care of your
nutribullet
®
device can increase the risk
of property damage, serious personal
injury, or death.
• In order to avoid a hazard due to
inadvertent resetting of the thermal
cut-out, this appliance must not be
powered or operated through an
external switching device, such as a
timer, or connected to a circuit that is
regularly switched on and o by
the utility.
• NEVER use the unit in countries
or locations with incompatible
electrical specifications or plug
types.
• DO NOT use the unit with a voltage
converter device, as it may cause
electrical shorting, fire, or electric
shock, all of which may result
in personal injury or property
damage.
• Do not use the unit if the cord, plug,
or Motor Base has been immersed in
water or other liquids.
76
• HOW TO CLEAN UP A SPILL:
STEP 1: The most important thing
is to UNPLUG the motor base before
cleaning!
STEP 2: Make sure the blade is not
attached to the motor base.
STEP 3: Use a damp cloth to
wipe down the inside and outside of
the Motor Base.
• Do not attempt to plug the unit into
an electrical outlet with wet hands.
• Do not use the cord, plug, or Motor
Base if it has been immersed in
water or other liquids. Any significant
spillage on, under, or around the
Motor Base should be cleaned and
dried before plugging in and using
the unit.
• Do not modify the electrical cord in
any way.
• Do not attempt to plug the unit into
an electrical outlet with wet hands.
• Avoid contact with the control panel
display when the power icon is
illuminated to prevent inadvertent
and unexpected operation of
the unit.
• Do not modify the electrical cord in
any way.
• Do not operate any unit with a
damaged electrical cord or plug.
The electrical cord and plug are
not suitable for replacement. If
damaged, the appliance should be
replaced. Contact Customer Service
for assistance at AU: 1300 285 538 /
NZ: 0800 232 63.
• Do not allow or place the electrical
cord near or touching any hot
surfaces, heat source, or flame,
including the stove.
• Do not allow the electrical cord to
hang over the edge of a table
or counter.
• Do not pull, twist, or damage the
power cord.
• Overloading the unit with ice or other
ingredients may overheat the motor
and engage the thermal breaker. If
the internal thermal breaker shuts
o the motor, unplug the Motor Base
and let it cool for an hour before
attempting to use it again. The
thermal breaker will reset when the
unit is unplugged and the thermal
breaker cools down.
• Always UNPLUG your nutribullet
®
when it is not in use, and when
assembling, disassembling, changing
accessories, or cleaning.
• NEVER pull the power cord to remove
the plug from the outlet. To unplug,
grasp the plug and pull from the
outlet.
• Use of incompatible parts or
aftermarket parts may result in
damage to your nutribullet
®
or
present safety hazards that may
cause personal injury or property
damage. When ordering replacement
parts, always use genuine nutribullet
®
parts and accessories from
bulletbrands.com.au / bulletbrands.
co.nz or contact Customer Service at
AU: 1300 285 538 / NZ: 0800 232 63.
VENTILATION:
• NEVER obstruct the ventilation
openings on the bottom of the
Motor Base of your nutribullet
®
device. Openings on the bottom of
the Motor Base should be free of
dust and lint and never obstructed.
Obstructing the ventilation openings
may overheat the motor, presenting a
fire hazard that may cause property
damage, serious personal injury,
or death.
• ALWAYS operate the nutribullet
®
on
a level surface, leaving unobstructed
space beneath and around the Motor
Base to permit proper air circulation.
Slots on the bottom of the Motor Base
are provided for ventilation to ensure
reliable operation and to prevent the
motor from overheating.
• NEVER place your nutribullet
®
on
top of flammable materials such as
newspapers, tablecloths, napkins,
dishtowels, placemats, or similar
materials.
MEDICAL SAFETY:
Always consult your physician regarding
health and nutrition concerns and
advice. The information contained in
this User Guide, accompanied Recipe
Guide, and/or online recipes are
general suggestions and ideals, and are
not meant to replace the advice of your
physician
• ALWAYS follow recommended
maintenance and care instructions
in the User Guide. NEVER operate
your nutribullet
®
with damaged
components. If your nutribullet
®
malfunctions in anyway, immediately
discontinue use and contact
Customer Service at AU: 1300 285
538 / NZ: 0800 232. If you have any
comments, questions, or concerns,
please go to bulletbrands.com.au /
bulletbrands.co.nz or call Customer
Service.
!
Save these
instructions!
98
Contents.
2 Important safeguards
10 What’s included
11 Assembly guide
12 Control panel
14 Blending with the Pitcher
18 Care & maintenance
21 nutribullet SmartSense™ Blender
one-year limited warranty
Thank you for purchasing the nutribullet
SmartSense™ Blender.
.
1110
Product confi gurations may vary. To see our full list of nutribullet
®
accessories,
please visit bulletbrands.com.au / bulletbrands.co.nz
What’s included.
1500-watt
motor base
pitcher lid with
vented lid cap
tamper
1.8 L pitcher
Assembly guide.
vented lid cap
pitcher lid
easy-pour
spout
tamper
pitcher
control panel
integrated blade
motor base
suction feet
Motor Base
Pitcher Lid (Straight On)
Pitcher
1312
Control panel.
AUTO
The AUTO button runs a
fully-automated cycle that
determines the exact time,
speed, and setting needed to
optimally blend ingredients.
POWER
The Power button turns on
the unit and illuminates the
Control Panel.
+
The + button increases the
blending speed within a range
of 1 to 5. Blending speeds must
be set prior to blending, and
can be adjusted at any point of
the blending process.
—
The — button decreases the
blending speed within a range
of 1 to 5. Blending speeds must
be set prior to blending, and
can be adjusted at any point of
the blending process.
Motor Base UIs
Motor Base UIs
Motor Base UIs
Motor Base UIs
BLEND
The Solid Circle BLEND button
activates blending for manual
speeds. Press the BLEND button
once to start blending, and a
second time to stop.
PULSE
The Dashed Circle PULSE
button activates the PULSE
blending function. Set your
blending speed, then press the
PULSE button for hands-on
control over blending time.
Press and release quickly to
pulse in short bursts, or press
and hold the button down for a
longer pulse.
TIMER
An LED timer counts up during
the blending cycle to keep
track of the length of your
blends. Both manual and
AUTO blending programs
display the timer during
blending. The speed setting
is displayed in the status bar
above the timer.
Motor Base UIs
Motor Base UIs
Motor Base UIs
1514
• Make sure the Motor Base is
plugged in for use.
• DO NOT attempt to operate the
Blending Pitcher on the appliance
without attaching the Pitcher Lid
and Vented Lid Cap.
• Never run the appliance
while empty.
• Appliance accessories are
not intended to be used in the
microwave; microwaves may
damage the accessories.
• Never leave the appliance
unattended while in use. Use extra
caution when blending hot liquids in
the Pitcher.
WARNING! ALWAYS ATTACH
THE PITCHER LID AND VENTED
PITCHER LID CAP TO THE PITCHER
BEFORE BLENDING HOT LIQUIDS
TO PREVENT SPLATTERING OF
CONTENTS WHICH MAY CAUSE
BURNS AND BODILY INJURIES. THE
VENTED LID CAP IS VENTILATED
TO ALLOW STEAM AND PRESSURE
TO BE RELEASED WHILE
GUARDING AGAINST EXCESS
SPLASHING. WHEN BLENDING HOT
INGREDIENTS, DO NOT PLACE
HANDS NEAR THE VENTED LID CAP
AS HOT STEAM AND SPLATTERS
RELEASED CAN RESULT IN
SCALDING OR BURN INJURIES.
FOR RECIPES THAT REQUIRE
CERTAIN INGREDIENTS TO
BE INCORPORATED DURING
BLENDING, CAREFULLY REMOVE
THE VENTED LID CAP AND POUR
OR DROP INGREDIENTS INTO
THE BLENDING MIXTURE. BE
ESPECIALLY MINDFUL WHEN
ADDING INGREDIENTS TO HOT
INGREDIENTS AND LIQUIDS, AS
ESCAPING STEAM OR SPLATTERS
MAY PRESENT A RISK OF INJURY.
DO NOT EXCEED THE MAX LINE
WHEN INSERTING ADDITIONAL
INGREDIENTS. ALWAYS REINSTALL
THE VENTED LID CAP AFTER
ADDING THE INGREDIENTS.
ALWAYS START THE BLENDING
CYCLE ON THE LOW SETTING,
INCREASING SPEED ONCE THE
INGREDIENTS ARE INTEGRATED
AND THE MIXTURE IS LEVEL
(NO SPLASHING).
Blending with
the Pitcher.
PLEASE KEEP THESE IMPORTANT
SAFEGUARDS IN MIND WHEN
USING THE APPLIANCE:
1 Place the Motor Base on a
clean, dry, level surface, such
as a counter or table.
2 Place the Pitcher on a
clean, dry, level surface and
add the ingredients to the
Pitcher, making sure they
do not exceed either the
lower LIQUID MAX (1.65L) or
higher solid MAX (1.8L) line.
4 Place the Pitcher onto the
Motor Base with the handle
pointed directly toward
the Control Panel. Twist
clockwise to lock the Pitcher
into place. (You should hear
a “click” when it’s locked.)
NOTE: If you are left-handed,
place the handle facing toward
the centre of the blending Control
Panel and twist clockwise.
Place the motor base
Place the pitcher lid
Place the pitcher
Place the pitcher lid
3 Mount the Pitcher Lid
with Vented Lid Cap onto
the Pitcher with the spout
opposite the handle. The
Pitcher Lid with Vented
Lid Cap will snap into
place when secured onto
the Pitcher.
1716
7 Press the + or - buttons
to increase or decrease
blending speeds. Press
the Solid Circle to start a
blending cycle. Press the
Dotted Circle for pulse
blending. Press AUTO for
an automated, high-speed
blending cycle.
NOTE: You can press the Solid
Circle or AUTO buttons again to
pause or stop a blending cycle.
8 Once the blending cycle is
complete, wait for the blades
to stop turning.
6 Press the Power Button to
turn on the Blender.
You will see the Control
Panel illuminate.
5 Plug the Motor Base’s
power cord into an
electrical outlet.
Plug in the motor base
Press the Control Panel
Wait for the blades to stop turning
Press the power button
9 Press the Power Button to
turn o the blender.
10 Twist the Pitcher
counterclockwise to unlock,
then lift it o the Motor Base.
Pour and enjoy!
Remove the pitcher
Wait for the blades to stop turning
1918
Care & maintenance.
Here’s how to clean
your nutribullet
®
:
1 ALWAYS POWER OFF THE
UNIT and UNPLUG the
Motor Base from the power
outlet when it is not in use.
Only attempt to handle the
appliance once all parts
have stopped moving! This
includes during assembly
and disassembly, while
changing accessories
during cleaning, and any
time you leave the machine
unattended.
2 Detach the nutribullet
®
Pitcher from the
Motor Base.
3 Clean the individual
components (Motor
Base and Pitcher) as
recommended in the
following pages.
• If preferred, hand-wash the
Pitcher with soap and water.
Stuck-on ingredients might
require extra scrubbing with a
dish brush or sponge.
• Regularly check the
structure of the Pitcher and
twisting threads for cracking,
crazing, or breakage.
If damaged, replace
immediately to prevent the
risk of personal injury.
WARNING! NEVER USE A
PITCHER THAT DOES NOT
PROPERLY ALIGN WITH THE
BLADE. Doing so may cause
the Pitcher and Motor Base to
separate, exposing the blade
assembly and potentially
causing severe personal injury.
EXTRACTOR BLADE:
WARNING! Blades are sharp!
Handle the Extractor Blade
with care when cleaning!
• Clean blades immediately after
each use. For stubborn buildup,
use a small brush or sponge to
dislodge. After washing, dry the
Extractor Blade completely.
• Do not remove any
components of the Extractor
Blade; this can result in
permanent damage to the
Blade, resulting in leakage
when blending. If, over time,
the Extractor Blade becomes
loose or damaged, you may
MOTOR BASE:
• To avoid the risk of injury,
NEVER attempt to clean the
actuator system on the Motor
Base while the nutribullet
®
Blender is plugged in.
• Do not attempt to remove any
pieces from the Motor Base.
• Use a sponge or dishcloth
dampened with warm soapy
water to wipe down the Motor
Base until clean.
• To clean leakage residue from
the Motor Base, wipe with a
damp sponge and warm water.
• If necessary, you may use
a small brush to scrub the
actuator system area to ensure
it’s clean.
WARNING! Never submerge
the Motor Base in water.
NUTRIBULLET
®
PITCHER:
WARNING! Blades are sharp!
Use caution when cleaning
the Pitcher.
• The Pitcher is dishwasher-safe.
We recommend rinsing and
briefl y scrubbing it with a dish
brush to remove any remaining
debris before placing it in the
dishwasher. NEVER use the
heat/sanitise cycle to wash the
Pitcher — high temperatures
can warp the plastic.
Plug in the motor base
Remove the pitcher
Plug in the motor base
2120
If your product becomes
defective due to faulty
material or workmanship
within a period of 1
year from the date of
purchase, we warrant
to do the following:
• For New Zealand Consumers:
We will replace the product
with a new product, free of
charge, or repair the product
at our cost, at our discretion.
• For Australian Consumers:
Our goods come with
guarantees that cannot be
excluded under the Australian
Consumer Law. You are
entitled to a replacement or
refund for a major failure
and for compensation for any
other reasonably foreseeable
loss or damage. You are also
entitled to have the goods
repaired or replaced if the
goods fail to be of acceptable
quality and the failure does
not amount to a major failure.
one (1) year limited
replacement warranty
statement.
YOUR WARRANTY
IS SUBJECT TO THE
FOLLOWING CONDITIONS:
• DO NOT operate the
appliance with a damaged
plug or cord, or if the unit has
been dropped, damaged or
dropped in water. To avoid
the risk of electric shock, do
not disassemble or attempt
to repair the appliance
on your own. If the supply
cord is damaged, it must
be replaced by a qualified
electrician in order to avoid
a hazard. Incorrect re-
assembly or repair can
cause a risk of electric shock
or injury to persons when the
appliance is used.
• The item has not been
misused, abused, neglected,
altered, modified or repaired
by anyone.
• The item has been subjected
to fair wear and tear.
• The item has not been used
for trade, professional or
hire purposes.
order a new Extractor Blade by
contacting Customer Service
at AU: 1300 285 538 / NZ: 0800
232 633.
• Periodically inspect your
Extractor Blade. If the blades
do not rotate freely or are
damaged, immediately
discontinue use and contact
Customer Service. For optimal
performance, we recommend
replacing the Blade every
6 months, or as needed,
depending on use.
WARNING! Never leave the
Extractor Blade exposed when
storing. Always attach the
Extractor Blade to the Pitcher
for proper storage.
TAMPER:
• Always hand-wash the Tamper
with soap and water. Stuck-on
ingredients might require extra
scrubbing with a dish brush
or sponge.
STUBBORN CLEANUP:
If ingredients dry inside the
nutribullet
®
Pitcher, fill your vessel
with room- temperature water
(70°F/21°C) to the liquid MAX line
and add 1-2 drops of dish soap.
Attach the Pitcher Lid with the
Vented Lid Cap inserted, and
place the Pitcher on the Motor
Base. Blend on LOW for 20-30
seconds; this should loosen debris
enough to scrub away with soap
and water.
STORING:
Store the nutribullet
®
Pitcher
upright with the Pitcher Lid
secured on top. Do not place
anything on top of the Pitcher Lid.
Store the remaining pieces in a
safe place where they will not be
damaged and won’t cause harm.
For replacement
parts.
To order additional parts
and accessories, please visit
our website at bulletbrands.
com.au / bulletbrands.co.nz or
feel free to contact Customer
Service at AU: 1300 285 538 /
NZ: 0800 232 633.
2322
• The item has not sustained
damage through foreign
objects, substances or accident.
YOUR WARRANTY
DOES NOT COVER:
• Components that are
subject to natural wear
and tear caused by
normal use in accordance
with operating instructions.
• Unauthorised/improper
maintenance/handling or
overload is excluded from
this warranty.
• For guarantee claims, you
will need to submit a proof
of purchase in the form of
a valid receipt that displays
date and place of purchase.
This warranty does not replace
but is in addition to your
statutory rights.
This warranty does not apply
to accessories supplied with
the item.
This warranty applies only to
the original purchaser and
may not be transferred.
Replacement items will
be covered by the limited
warranty for the balance of the
warranty period from the date
of the original purchase.
PLEASE NOTE:
Only the defective product
or parts returned to place of
purchase will be replaced
under this warranty.
NEW ZEALAND
PO Box 100-707
NSMC
Auckland 0745
0800 232633
bulletbrands.co.nz
AUSTRALIA
PO Box 574
South Morang
Victoria 3752
1300 285538
bulletbrands.com.au
nutribullet
®
is a registered trademark of CapBran Holdings, LLC.
Copyright © 2024 CapBran Holdings, LLC. All rights reserved.
Los Angeles, CA 90024, USA. Made in China.
Capital Brands Distribution, LLC | All rights reserved.
nutribullet
®
and the nutribullet
®
logo are trademarks of CapBran Holdings,
LLC registered in the U.S.A. and worldwide.
Illustrations may dier from the actual product. We are constantly striving
to improve our products, therefore the specifications contained herein
are subject to change without notice.
240717_NBF07600
