Loading ...
Loading ...
Loading ...
Refrigerator Location
Do not install refrigerator
where temperature will be
below
60”F.
because it will not
run often enough to maintain
proper temperatures.
Do install it on a floor strong
enough to support it fully loaded.
Also see Energy-Saving Tips.
Clearances
Allow the following clearances
for ease of installation, proper
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..5/8”
Sides
Top . . .
. . . . . . . . . . . . . . . . . . . . . . . . . .0”
air circulation and plumbing and
(Ifhuilt
ill,
electrical connections:
allow
718’’,
ftit-
hin,qe
co~’ers.
)
Back . . . . . . . . . . . . . . . . . . . . . . . . . 1“
Allow following door clearances:
Refreshment Center Side . . . . .
.3X”
Freezer Side . . . . . . . . . . . . . . . . . . . . . 1
X“
Rollers
Adjustable rollers behind the base grille enable you to
Turn roller adjusting screws
move the refrigerator away from the wall for cleaning.
clockwise to raise refrigerator,
These rollers should be set so the refrigerator rests
counterclockwise to lower it.
f’irmly
on the
tloor.
To assure that the doors will close
Use adjustable wrench (3/8” hex
automatically from a halfway-open position, there is a
head bolt) or pliers.
k
&
built-in tilt from the front to
the
back of the cabinet.
Side-by-side
ret’rigerators
also have specially designed
When adjusting front rollers
f’or
door
hinges
that
lift
both doors slightly when opened,
proper door closure, we recommend that the bottom
front edge of the cabinet be approximately 5/8” from
allowing the force of gravity to help close them securely.
the floor.
To adjust rollers,
remove the base
grille
by
grasping it at the bottom
and
pul!ing
it out.
P
‘1
To
replace base grille,
,,..
-,*<..-
.
.
t,
~ ?
+<.
align prongs on back
>$
/;”//
,
;;&Z+*/.
of grille with clamps in
cabinet and push back
.-.=>
,.;
/
\
until the grille snaps
into place.
I
Water Supply to Icemaker
(on some models)
If your refrigerator has an icemaker, or if you plan to
add an icemaker later, the ice maker will have to be
connected to a cold water line. A water supply kit
containing copper tubing, shut-off valve., fittings and
instructions is available at extra cost from your dealer.
There should be sufficient tubing from the cold water
supply to the icemaker inlet to
allow
you to move the
refrigerator out from the wall several feet (approximately
8 feet of l/4° copper tubing in three 10” diameter coils).
Do not use kits with plastic tubing, since there is water
pressure in the supply line at all times.
Preparing to Move
Disconnect power cord from
wall
outlet, remove
all
food, and clean and dry the interior.
Secure all loose items such
as
grille, shelves and
storage pans, by taping them securely in place to
prevent damage.
Be sure refrigerator stays in
upri,yht
position during
actual moving and in van. Refrigerator must be
secured in van to prevent movement. Protect the
outside of the refrigerator with
a
blanket.
I
Preparing for Vacation
For shorter vacations,
remove perishable
foods
and
with baking soda solution
of one tablespoon of soda to
leave controls at regular settings. However, if room
one quart of water. Wipe dry. To prevent odors, leave
temperature is expected to drop below 600
F
., follow
open box of soda in refrigerator. Leave doors open.
instructions in Temperature Control section.
Move the icemaker feeler arm to the STOP (up) position
For extended vacations
or
absences,
remove food
and be sure to shut off the
water
supply to the refrigerator.
and shut off power to the refrigerator. Clean the interior
21
Loading ...
Loading ...
Loading ...