Loading ...
Loading ...
Loading ...
WARNING
To reduce the risk of personal injury, two people
are required to lift the unit onto the pedestal.
W526
13. With proper help, tilt unit forward and lift. Carefully set unit
onto pedestal. Make sure front of unit is positioned to line up
with pedestal’s mounting holes. Refer to Figure 4 . Make sure
pedestal is square with front and back of unit.
14. Gather contents of the parts bag.
15. Remove front access panel at the lower front of unit by re-
moving two screws from bottom edge of panel. Refer to Fig-
ure 5 .
16. Attach dryer to pedestal by placing two cap screws, washers
and nuts from inside front of unit into threaded holes on ped-
estal. Nuts act as spacers to keep screw head above dryer base
leg holes. Refer to Figure 4 . Tighten screws after partially in-
stalling both.
NOTE: Remaining two screws, washers and nuts are
not required to attach dryer to pedestal.
17. Attach strap included in parts bag to dryer cabinet rear panel
and to center back of pedestal. Remove one screw from mid-
dle of dryer rear panel. Refer to Figure 9 . Reattach screw
with strap using long slot hole. Do not tighten yet. Attach
strap to back of pedestal using two screws. Refer to Figure 9 .
Tighten all screws.
FLW128K_SVG
1
2
1. Screw From Dryer Rear Panel
2. Strap
Figure 9
18. Reinstall front access panel.
19. Move unit with pedestal into desired location. Position rear of
elevated base pedestal to allow sufficient room for reinstalla-
tion. Refer to installation instructions supplied with unit for
proper spacing and clearance.
20. Check if unit is level. If needed, make final adjustment to lev-
eling legs on pedestal.
21. Follow Installation Instructions from unit to finish installing
the unit.
22. Reattach dryer vent.
23. On gas dryers, reattach gas to dryer.
24. Reconnect electrical power to unit.
Commercial Dryer Installation
(PDC106B, PDC108B, PDC110B,
PDC112B Pedestals)
1. Disconnect electrical power to unit.
2. Disconnect dryer vent.
3. On gas dryers, disconnect gas from dryer.
4. Remove four leveling legs, nuts and rubber feet from parts
bag included with pedestal.
5. Place rubber feet on all four leveling legs.
6. Thread each nut down to within one inch of the bottom of
each leveling leg. Leave room for a wrench to fit for adjusting
leg and tightening nut. Refer to Figure 1 .
7. Screw leveling legs with nuts into bottom flange of the elevat-
ed base pedestal.
NOTE: Alternatively, this pedestal may be bolted to
a concrete or wooden structure using industry
standard mounting methods.
8. Place pedestal into desired final location. Front of pedestal
has two bolt holes on top, front flange. Refer to Figure 8 .
9. Level pedestal from front to back and from side to side by
screwing leveling legs into or out of pedestal. Refer to Figure
3 . Turn leg clockwise to lift or counterclockwise to lower.
10. Once pedestal is level, tighten the nuts installed in step 6 up
against bottom of pedestal. Refer to Figure 3 . Make sure to
hold leg when tightening nut.
11. If installing two or more pedestals in a row, they may be bolt-
ed together. Use four 5/16 inch cap screws and nuts included
in kit. Place two 3/8 inch flat washers included in kit between
pedestals to allow for unit clearance.
WARNING
To reduce the risk of personal injury, two people
are required to lift the unit onto the pedestal.
W526
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
6 Form No. 7-04-47ENR14
Loading ...