Loading ...
Loading ...
Loading ...
Before You Call 57
Oven control panel chimes and
displays an F code error.
• Oven control has detected a fault or error condition. Press STOP to clear the error code.
Try bake or broil function. If the F code error repeats, turn off power to appliance, wait 5
minutes and then repower appliance. Set clock with correct time of day. Try bake or broil
function again. If fault recurs, press STOP to clear.
Soil not completely removed after
self clean.
• Self clean was interrupted. Review “Self Clean” on page 46.
• Excessive spills on oven bottom. Clean before starting self clean.
• Failure to clean soil from the oven frame, the door liner outside the oven door gasket,
and the small area at the front center of the oven bottom. These areas are not in the self
cleaning area, but they get hot enough to burn on residue. Clean these areas before
starting the self clean cycle. Burned-on residue can be cleaned with a stiff nylon brush
and water or a nylon scrubber. Be careful not to damage the oven gasket.
Appliance is not level. • Poor installation. Place oven rack in center of oven. Place a level on the oven rack.
Adjust leveling leg at base of appliance until the oven rack is level.
• Kitchen cabinet alignment may make oven appear not level. Be sure cabinets are
square and have sufficient room for appliance clearance.
• Cabinets not square or are built in too tightly. Contact builder or installer to make
appliance accessible.
Fan noise occurring after the oven is
turned off.
• Some models are equipped with a cooling fan that runs during the cooking process to
cool internal electronic components. It is normal for this fan to continue to run for an
extended period of time, even when the oven is off.
Surface burner flame is too high. • Surface control knob is set too high. Adjust to lower flame setting. Burner caps are not
seated properly. Check that all surface burner caps are level and seated correctly on
surface burner heads. See “Cleaning Surface Burner Heads” on page 51.
• Incorrect L.P. conversion. Refer to L.P. conversion kit instructions to correct.
Surface burners do not ignite. • Surface control knob was not completely turned to LITE. Push in and turn the surface
control knob to LITE until burner ignites and then turn control knob to desired flame size.
• Burner ports are clogged. With the burner OFF, use a small-gauge wire or needle to
burner head slots and ignition ports. See “Cleaning Surface Burner Heads” on page 51.
• Range power cord is disconnected from outlet (electric ignition models only). Be sure
power cord is securely plugged into the power outlet.
• Electrical power outage. Burners may be lit manually. See“Setting Surface Controls” on
page 13.
• Be sure the gas supply to the range is turned on.
Surface burner flame uneven or only
part way around burner cap.
• Burner slots or ports are clogged. With the surface burner OFF, clean ports with a small-
gauge wire or needle. Also, moisture is present after cleaning. Lightly fan the flame and
allow burner to operate until flame is full.
• Burner caps are not seated properly. Check that all burner caps are level and seated
correctly on burner heads. See “Cleaning Surface Burner Heads” on page 51.
Surface burner flame is orange. • Dust particles in main gas line. Allow the burner to operate a few minutes until flame
turns blue. In coastal areas, a slightly orange flame is unavoidable due to salt content in
air.
• Incorrect L.P. conversion. Refer to L.P. conversion kit instructions to correct.
Convection fan does not rotate • Oven door is open. Convection fan will turn off if oven door is opened when convection
is active. Close oven door.
“d-O” is displayed • The door was left open and control set for self-cleaning cycle. Close the door and press
STOP.
Cannot move appliance easily.
Appliance must be accessible for
service.
• Cabinets not square or are built in too tightly. Contact builder or installer to make
appliance accessible.
• Carpet interferes with appliance. Provide sufficient space so appliance can be lifted over
carpet.
• Gas line is hard-plumbed. Have a flexible CSA International approved metal appliance
connector installed.
Loading ...
Loading ...