INSTRUCTION MANUAL
Phone: 1-360-734-3482 • On-Line Technical Support: [email protected]
COPYRIGHT © DECEMBER 2003 BY WOODSTOCK INTERNATIONAL, INC. REVISED OCTOBER, 2008.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT
THE WRITTEN APPROVAL OF WOODSTOCK INTERNATIONAL, INC.
MODEL
W1669 and W1670
RADIAL DRILL PRESS
#6218CR
Printed in China
WARNING
Some dust created by power sanding, sawing, grind-
ing, drilling, and other construction activities con-
tains chemicals known to the State of California to
cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement, and
other masonry products.
• Arsenic and chromium from chemically
treated lumber.
Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your
exposure to these chemicals: work in a well venti-
lated area, and work with approved safety equip-
ment, such as those dust masks that are specially
designed to filter out microscopic particles.
-1-
ASSEMBLY OPERATIONS MAINTENANCEELECTRICAL ADJUSTMENTSSAFETYINTRODUCTION
CONTENTS
INTRODUCTION............................................................................................. 2
About the W1669 and W1670 Radial Drill Presses ......................................................... 2
Woodstock Technical Support ................................................................................. 2
SAFETY....................................................................................................... 4
Standard Safety Instructions .................................................................................. 4
Additional Safety Instructions for Drill Presses ............................................................ 5
Avoiding Potential Injuries .................................................................................... 6
ELECTRICAL................................................................................................. 7
110V Operation ................................................................................................. 7
Extension Cords ................................................................................................. 7
Grounding ........................................................................................................ 7
ASSEMBLY.................................................................................................... 8
Base and Column ............................................................................................... 9
Table Support ................................................................................................. 10
Headstock ...................................................................................................... 12
Drill Chuck and ............................................................................................... 13
Spindle ......................................................................................................... 13
ADJUSTMENTS.............................................................................................14
Belt Tension ................................................................................................... 14
Feed Shaft Spring Tension ................................................................................... 15
Quill-Shaft Screw ............................................................................................. 16
Table ............................................................................................................ 17
OPERATIONS...............................................................................................18
Test Run ........................................................................................................ 18
Headstock ...................................................................................................... 19
Changing Drill Bits ............................................................................................ 20
Speed Changes ................................................................................................ 21
Drill Press RPM Chart ......................................................................................... 22
Drilling Depth ................................................................................................. 22
Drill, Cutter, and Hole Saw Suggested RPM Chart .................................................. 23
MAINTENANCE.............................................................................................25
General ......................................................................................................... 25
Table and Base ................................................................................................ 25
Lubrication .................................................................................................... 25
Troubleshooting ............................................................................................... 26
W1669 and W1670 Drill Press 110V Wiring ............................................................... 27
W1669 and W1670 Parts ..................................................................................... 28
W1669 Parts ................................................................................................... 30
W1670 Parts ................................................................................................... 32
Accessories .................................................................................................... 34
Notes ........................................................................................................... 36
Warranty ....................................................................................................... 38
-2-
The SHOP FOX
®
Model W1669 and W1670 Radial Drill Presses have been specially designed by
Woodstock International, Inc. to provide many years of trouble free service. Close attention to detail,
ruggedly built parts and a rigid quality control program assure safe and reliable operation.
The Model W1669 and W1670 Radial Drill Presses are capable of a wide variety of drilling and sanding
operations. Purchasing the D2677 Drum Sander Set and D2722 Mandrel allows you to sand small or finely
detailed pieces. The tilting table and headstock allows surfaces to be sanded and drilled at many different
angles. The Model W1669 and W1670 is packaged with a drill chuck, motor and paddle switch with remov-
able safety key.
Woodstock International, Inc. is committed to customer satisfaction in providing this manual. It is our
intent to make sure all the information necessary for safety, ease of assembly, practical use and dura-
bility of this product be included.
Woodstock.Technical.Support
About.the.W1669.and.W1670.Radial.Drill.Presses
INTRODUCTION
INTRODUCTION
We stand behind our machines! In the event that questions arise about your machine, parts are miss-
ing, or a defect is found, please contact Woodstock International Technical Support at 1-360-734-3482 or
send e-mail to: tech-support@shopfox.biz. Our knowledgeable staff will help you troubleshoot prob-
lems and send out parts for warranty claims.
If you need the latest edition of this manual, you can download it from http://www.shopfox.biz.
If you still have questions after reading the latest manual, or if you have comments please contact us at:
Woodstock.International,.Inc.
Attn:.Technical.Suppor t.Department
P.O..Box.2309
Bellingham,.WA.98227
-3-
Motor Type: ...................................................... TEFC Capacitor Start Induction
Motor: .............................................. 1⁄2 HP, 110V, 5 Amp., Single-Phase ⁄ 60 Hz
RPM: .............................................................................................. 1725
Power Transfer: ........................................................................ V-Belt Drive
Bearings: ................................................... Shielded & Lubricated Ball Bearings
Switch: ............................................ Toggle ON/OFF Switch, w/ Safety Lock Key
Spindle Travel: .................................................................................3-1⁄4''
Maximum Distance, Spindle to Base: ......................... W1669 = 15-1⁄2,'' W1670 = 49''
Maximum Distance, Spindle to Table: .................... W1669 = 9-1⁄4,'' W1670 = 31-1⁄2''
Overall Height: ..............................................W1669 = 31-1⁄2,'' W1670 = 64-1⁄2''
Head Tilt: .......................................................................45° Left, 90° Right
Table Tilt: ....................................................................... 90° Left and Right
Table Rotation: .................................................................................. 360°
Spindle Taper: ...................................................................................JT-33
Swing: ............................................................................................... 34''
Chuck Size: ..........................................................5⁄8'' (1-13mm JT-33), Keyed
Speeds: ........................................................................... 5, Belt Controlled
Range of Speeds: ...................................................
550, 880, 1570, 2490, 3470 RPM
Drilling Capacity: ..........................................................1⁄2'' Diameter in Steel
Approximate Shipping Weight: .......................... W1669 = 100 lbs., W1670 = 150 lbs.
Specifications
INTRODUCTION
-4-
READ.MANUAL.BEFORE.OPERATING.MACHINE
FAILURE.TO.FOLLOW.INSTRUCTIONS.BELOW.WILL.
RESULT.IN.PERSONAL.INJURY
1.. Thoroughly.read.the.instruction.manual.before.operating.your.machine..Learn the applications,
limitations and potential hazards of this machine. Keep manual in a safe, convenient place for
future reference.
2. Keep.work.area.clean.and.well.lighted..Clutter and inadequate lighting invite potential hazards.
3. Ground.all.tools..If a machine is equipped with a three-prong plug, it must be plugged into a
three-hole electrical outlet or grounded extension cord. If using an adapter to aid in accommodat-
ing a two-hole receptacle, ground the adapter using a screw to a known ground.
4. Wear.eye.protection.at.all.times..Use safety goggles with side shields or safety goggles, meeting
the national safety standards, while operating this machine.
5. Avoid.dangerous.environments..DO.NOT operate this machine in wet or open flame environ-
ments. Airborne dust particles could cause an explosion and severe fire hazard.
6. Ensure.all.guards.are.securely.in.place.and in working condition.
7. Make.sure.switch.is.in.the.“OFF”.position.before connecting power to machine.
8. Keep.work.area.clean;.free of clutter, grease, etc.
9. Keep.children.and.visitors.away..All visitors should be kept at a safe distance away while operat-
ing unit.
10. Childproof.your.workshop.with padlocks, master switches, or by removing starter keys.
11. Disconnect.the.machine.when.cleaning,. adjusting,.or.servicing.
Indicates an imminently hazardous situation which, if not avoided, WILL
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, MAY
result in minor or moderate injury and damage to the machine. It may
also be used to alert against unsafe practices.
This symbol is used to alert the user to useful information about proper
operation of the equipment.
NOTICE
SAFETY
Standard.Safety.Instructions
SAFETY
1.. DRILL.PRESS.SPEEDS..Always operate your drill press at speeds that are appropriate for the drill
bit size and the material that you are drilling.
2.. DRILLING.HOLES. Feed the drill bit evenly into the workpiece. Back the bit out of deep holes and
clear the chips with a brush after you have turned the machine off.
3.. USING.THE.CORRECT.DRILL.BITS. Use only round, hex or triangular shank drill bits, and make sure
the drill bit you are using is tightened properly..
4.. SAFE.MAINTENANCE. Never do maintenance or change speeds with this machine plugged in.
5.. USING.SERVICEABLE.TOOLS. Never use tools that are in poor condition. Cutting tools that are dull
or damaged are difficult to control and may cause serious injury.
6.. DRILLING.OPERATIONS. Never hold a workpiece by hand while drilling, never drill sheet metal
unless it is clamped securely to the table, and always secure the workpiece to the table before
drilling.
7.. SECURING.A.WORKPIECE. Properly position workpieces to avoid drilling into the table.
8.. PROTECTING.YOUR.EYES. A face guard used or safety goggles is recommended.
9.. WORKING.HABITS. Habits – good and bad – are hard to break. Develop good habits in your shop and
safety will become second-nature to you.
-
5-
12. DO.NOT. force.the. tool.. The machine will do a safer and better job at the rate for which it was
designed.
13. Use.correct.tool..DO.NOT force machine or attachment to do a job for which it was not designed.
14. Wear.proper.apparel..DO.NOT wear loose clothing, neck ties, gloves, jewelry; and tie back hair.
15. Remove.adjusting.keys.and.wrenches..Before turning the machine on, make it a habit to check that
all adjusting keys and wrenches have been removed.
16. Use.proper.extension.cord..When using an extension cord, make sure it is in good condition.
When extension cord is 100 feet and less in length, use those that are rated Standard Service
(grade S) or better, and that have a conductor size of 16 AWG. A drop in line voltage, loss of
power and overheating can result when using an undersized cord. The extension cord should have a
ground wire and ground plug pin, as well.
17. Keep.proper.footing.and.balance at all times.
18. DO.NOT.leave.machine.unattended..Wait until it comes to a complete stop before leaving the area.
19. Perform.machine.maintenance.and.care.. Follow lubrication and accessory attachment instruc-
tions in the manual.
20. Keep.machine.away.from.open. flame..Operating machines near pilot lights and/or open flames
creates a high risk if dust is dispersed in the area. Dust particles and an ignition source may cause
an explosion. DO.NOT operate the machine in high risk areas, including but not limited to, those
mentioned above.
Additional.Safety.Instructions.for.Drill.Presses
SAFETY
Figure.1..Never drill while holding the
workpiece by hand.
Figure.2. Keep fingers away from spinning
drill bits, cutters, and sanding surfaces.
Figure.3. Remove switch safety key when not
in use.
-6-
Avoiding.Potential.Injuries
SAFETY
-7-
Ground.this.machine! The electrical cord sup-
plied with the W1669 and W1670 Radial Drill
Press comes with a grounding pin. DO.NOT
remove the pin if your outlet does not accept a
ground pin, see Figure.4. Have the outlet box
replaced by a qualified electrician or have an
appropriate adapter installed.
Remember, an adapter with a grounding wire
does not guarantee the machine will be ground-
ed. A ground source must always be verified in
the electrical circuit within the wall or conduit.
Grounding
ELECTRICAL
110V.Operation
The SHOP FOX
®
W1669 and W1670 Radial Drill
Presses operate at 110 volts only. The motor
supplied with your new drill press is rated at
1⁄2 HP and will draw approximately 5 amps.
When choosing an outlet for this machine, con-
sider using one with a 15 amp circuit breaker
or fuse. Keep in mind that a circuit being used
by other machines or tools at the same time
will add to the electrical load being applied by
the drill press. Add up the load ratings of all
machines on the circuit. If this number exceeds
the rating of the circuit breaker or fuse, use a
different outlet.
DO.NOT modify an existing low-amperage
circuit by only replacing the circuit breaker
with a breaker rated for a higher amperage.
The breaker and the complete circuit must be
replaced by a qualified electrician.
Any. electrical. outlet. and.
circuit. that. you. plug. your.
machine. into. must. be.
grounded.. Serious. injury.
and/or.fire.may.occur.if.this.
warning.is.ignored!
Figure.4..Never remove a grounding pin.
If you must use an extension cord, use the guide-
lines below to determine the correct cord length
and gauge. If you use an undersized-gauge exten-
sion cord or one that is too long, heat will gener-
ate in the cord and fire or circuit damage may
result.
•Use.a.cord.rated.for.Standard.Service.(Grade.S)
•Use.a.cord.that.is.16.gauge.and.100.feet.or.........
..less
•Use.a.cord.with.a.ground.wire.and.pin
•Use.only.undamaged.cords
Extension.Cords
ELECTRICAL
-8-
EYE.HAZARD!
Wear. safety. goggles. during.
all. assembly. procedures..
Otherwise. serious. personal.
injury.may.occur!
ASSEMBLY.
Figure.5..Component inventory.
A.. Headstock Assembly
B.. Base
C.. Column
D.. Table
E.. Table Bracket Assembly
F.. Drill Chuck and Key
G.. Spindle Handles and Knobs (3)
H.. W1669: Hex Wrenches 3MM,
5MM, 10MM
I.. Column Bolts (4)
J.. Belt Cover Knob and Screw
K.. Lift Handle Crank
L.. Pinion Gear
M.. Lock Handles (4)
N.. Rack
O.. Column Ring
P.. Open End Wrench (Not shown)
Q.. W1670: Lock Lever
G
D
O
L
I
C
N
S
H
M
K
E
F
J
B
Q
Use the list below and Figure.5 to inventory your shipment before beginning assembly. If any parts
are missing, call Woodstock International, Inc. at 360-734-3482 or [email protected].
While the main components of the SHOP FOX
®
W1669 and W1670 Drill Presses are assembled at the fac-
tory, some assembly is required. The following order of procedures is the recommended sequence.
R.. W1670: Table Support Arm
Bracket
S.. W1670: Hex Wrenches, 3MM
and 5mm
T.. Mounting Hardware
(Refer to the parts list on
Page.30.for details)
Use the parts list at the back of
this manual when ordering parts.
.SUFFOCATION.HAZARD!
Immediately..discard.all.plastic.
bags.and.packing.materials.to.
eliminate. a. suffocation. haz-
ard.for.children.and.animals.
R
T
A
ASSEMBLY
-9-
Figure.6..Secure base to floor.
Figure.7..Secure base to 4' x 4' x
3
⁄4" plywood.
Base.and.Column
1.. UNPLUG.THE.MACHINE!
. •. If.installing.the.W1670.to.a.concrete.. .
. floor,.do.these.steps:
a. Position the drill press in a sensible work
area where the base sits flat at all four
corners, or the base may crack when you
tighten the fasteners.
b. Mark and drill the floor, and install the
concrete anchor bolts (not included) (see
Figure.6).
c. Position the base and fasten the base to
the floor carefully as not to crack it.
. . •. If.installing.the.W1670.to.a.plywood.. .
. . base,..do.these.steps:
a. Center the drill press base along the back
edge of the 4' x 4' x
3
⁄4" sheet of plywood
(see Figure.7).
b. At each corner of the drill press base, drill
the plywood.
c. Secure the base to the plywood with four
3/8" diameter bolts, washers, and nuts
(not included).
. . . •..If.installing. the.W1669.to.a.tool.table...
. . ....or.workbench,.do.these.steps:
a. Position the base on a bench or tool table
capable of supporting approximately 100
lbs.
b. Drill two mounting holes (Figure.8), and
secure the base to the table with the two
supplied carriage bolts and wing nuts.
2.. Place the column on the base, and install the
four column bolts supplied.
For maximum stability, secure the W1670
floor-model drill press to a sturdy surface like
a floor or a 4' x 4' x
3
⁄4" piece of plywood. For
the W1669 bench-model, secure it to a sturdy
workbench or tool table.
TIPPING.HAZARD!
Never.mount.a.drill.press.to.a.
mobile. base.. Mount. the. drill.
press.base.to.a.sturdy.surface.
or.the.drill.press.may.tip.and.
cause.injury..
Figure.8..Workbench mounting holes.
Mounting
Holes
ASSEMBLY
-10-
Figure.11..Installing rack and table bracket.
Figure.10..Align set screw with flat pad on
pinion.
Table.Support
The W1669 comes with a one geared table
bracket. The W1670 comes with a geared table
bracket and table support arm, which allows
the distance between the column and table to
be adjusted. No table support parts are inter-
changeable between the two drill presses.
To.install.the.table.support.assembly,.do.
these.steps:
1.
. Insert the table lock lever through the un-
threaded hole (see Figure.9
) in the
table
bracket, and then tighten the lever into
the threaded side exactly three turns.
2..
Starting with the pinion gear, insert the
shaft into the table bracket and mesh the
teeth with the worm gear as shown in
Figure.9..
3..
Align the set screw in the crank handle
with the flat pad on pinion shaft.
4..
Tighten the 3mm set screw to lock the
handle in place (see
Figure.10).
5.
. Examine the rack and note that the rack
teeth at one end are cut closer to the end
of the rack than the other.
6.
Insert the rack through the table bracket
so the end that has the rack teeth cut clos-
er to the end is pointing down (see Figure.
11).
7.
Hold the rack against the worm gear and
slide the table bracket and rack onto the
column (see
Figure.
11).
Figure.9..Pinion and worm gear installation.
Pinion
Gear
Worm
Gear
Un-threaded Hole
Flat
Pad
Set Screw
ASSEMBLY
Figure.13..Column ring in the correct position.
8. Seat the rack tapered-point into the bevel
that is cut into the column support tube
(see Figure.12).
9.
Slide the column ring onto the column with
the inside bevel in the down position until
the rack tapered-point seats into the bevel
(see Figure.13).
10.
Position the column ring so the table
bracket and rack can just rotate around
the column without binding.
11. Carefully, snug the set screw to hold the
column ring in place. Over-tightening the
column ring will distort or split the column
ring.
Column Ring
Bevel
Figure.12..Bevel and rack seated correctly.
Tapered Rack
Point and
Column Support
Tube Bevel.
Set
Screw
ASSEMBLY
-11-
-12-
GET.help.to.lift.the.head-
stock,
. or. you. may. seri-
ously
. hurt. your. back. or.
drop.the.headstock..
The headstock is secured with a set screw so it
is aligned with the drill press base for balance
and weight distribution. DO.NOT over tighten
the set screw, or you will bend the column or
strip the threads.
Headstock
To.install.the.headstock.assembly,.do.these.
steps:
1.. Place the locking gib into the recessed
pocket on the inside of the column bracket
casting (see Figure.14).
2. With an assistant, lift and position the
headstock pocket over the column and
allow the headstock to slide down until
the column fully seats into the headstock
(approximately 2", see Figure.15).
3.. Rotate the headstock directly over the foot
of the base as viewed from the front of the
drill press.
4. Screw in the two lock handles on the sides
of the headstock.
5. Using a plumb bob and ruler, center the
headstock with the base, and tighten the
two set screws to secure the headstock to
the column (see Figure.16).
Figure.14..Locking gib installation.
Figure.15. Headstock-to-column installation.
Figure.16..Aligning the headstock.
Locking
Gib
ASSEMBLY
-13-
Drill.Chuck.and.
Spindle
Your keyed drill chuck attaches to the drill
spindle. When properly joined, the JT-33
tapers on the spindle and inside the chuck cre-
ate an almost permanent connection.
To.install.the.drill.chuck,.do.these.steps:
1... Clean the drill chuck and spindle with min-
eral spirits and follow all safety warnings
on the container (see Figure.17).
Note: Failure to clean the tapered mating
surfaces of the spindle and drill chuck may
result in a loose or wobbly chuck.
2. Use the provided chuck key to adjust the
jaws of the chuck until they are inside of
the drill chuck body (see Figure.18).
3. Place the drill chuck on the spindle and tap
the chuck onto the spindle with a block of
wood or a dead-blow hammer (see Figure.
18). DO.NOT.use a metal hammer to seat
the drill chuck onto the spindle!
Figure.18..Seating chuck into spindle.
Figure.17..Clean the chuck before installation.
Chuck Jaws
Recessed and
Protected
Inside of
Chuck
ASSEMBLY
-14-
ADJUSTMENTS
Belt.Tension
During the life of your drill press you will use differ-
ent belt and pulley combinations. No matter which
pulley combination you use, make sure that the belt
is tensioned properly
To.adjust.the.drive.belt.tension,.do.these.
steps:
1... UNPLUG.THE.DRILL.PRESS!.
2... Open the belt safety cover (see Figure.
19).
3.. Loosen both motor lock knobs at the side
of the headstock (see Figure.).
4... Slide the motor away from the headstock
until the belt is taut.
5... Hold the motor in position, and tighten the
lock screw, and make sure the belt deflec-
tion gap is correct when pinched together
between the pulleys (see Figure.21).
• If the gap between both inner sides of
the belt is greater or less than
3
⁄4" repeat
Steps.3-5 until the deflection gap is
3
⁄4".
• If the deflection gap is
3
⁄4" the belt is ten-
sioned correctly.
6... Close the belt safety cover.
UNPLUG. the. drill. press..
before. any. assembly,.
adjustment,. maintenance,.
or. belt. changing. proce-
dures.. Otherwise. serious.
personal.injury.may.occur!
Figure.19..Open belt safety cover.
Figure.20..Motor lock knob.
Figure.21..Measuring belt deflection.
Motor
Lock Knob
Push rod
Belt Deflection
gap should be
about
3
⁄4"
ADJUSTMENTS
-15-
Figure.23. Typical spring cover lock slot and
locking lug.
Spring-Cover
Lock Slot
Locking Lug
Figure.22..
Feed shaft return spring assembly.
Spring
Lock Cover
Jam Nut
and
Cover Nut
The feed shaft return spring is adjusted at the fac-
tory; however, during the life of the drill press you
may want to adjust the feed shaft return spring to
a greater tension for a stronger quill return.
To.adjust.the.feed.shaft.spring.tension,.do.
these.steps:
1... UNPLUG.THE.DRILL.PRESS!
2... Wipe off any oil on the spring-lock cover so
it will not slip when you hold the cover from
spinning (see Figure.22).
3... Make sure the quill is completely seated and
the depth stop reads zero.
4.. Put on thick leather gloves, and hold the
spring cover against the side of the head-
stock so the cover stays splined with the
locking lug; remove the jam nut and loosen
the cover nut approximately
1
⁄4" (6.4mm).
5... Pull the cover outward just enough to dis-
engage the spring-cover lock slot from the
locking lug (see Figure.23).
6... Rotate the cover counterclockwise to
increase spring tension, or let the cover
slowly unwind in the clockwise direction to
reduce spring tension (see Figure.23).
Feed.Shaft.Spring.
Tension
WEAR. safety. goggles. and.
gloves.when.adjusting.the.
feed. shaft. spring.. Serious.
injury. may. occur. if. this.
warning.is.ignored!
ADJUSTMENTS
Locking Lug
While you may never have to adjust the quill-
shaft screw, you should understand its func-
tion and know how to adjust it should you ever
need to remove the quill for cleaning. This
screw prevents the quill from rotating during
drilling and sanding procedures, and if adjusted
incorrectly, the quill may have lash or bind.
To.adjust.the.quill-shaft.screw,.do.these.steps:
1. UNPLUG.THE.DRILL.PRESS!.
2... Clean and lubricate the quill shaft with a
thin coat of light oil, so the quill travels
freely (see Figure.25).
3... Loosen the jam nut (see Figure.26).
4... Move the quill up and down through the
entire range of travel, and turn the quill-
shaft screw inward as far as it can go with-
out binding the quill.
5... Tighten the jam nut, and check the quill
movement for binding or play while moving
the quill up and down through its entire
range of travel.
6... Re-adjust the quill-shaft screw as required.
Figure.25..Clean and oil quill shaft.
Figure.26..Quill-shaft screw and jam nut.
Quill-Shaft
Screw
Jam
Nut
7... Engage the next available spring-cover
lock slot with the locking lug and hold the
spring lock cover tightly against the side of
the headstock (see Figure.24).
8... Snug the cover nut against the spring cover
just until the nut stops, and then back-
off the nut approximately
1
⁄3 turn, or just
enough so there is no binding anywhere
along spindle travel path.
9... Hold the cover nut and tighten the jam nut
against the cover nut.
-16-
Figure.24..Hold the spring cover tightly.
Cover Nut
Quill-Shaft.Screw
Lock Lug
ADJUSTMENTS
-17-
Table
The table can be adjusted for height, rotation,
and angle. The W1670 adds the fourth adjust-
ment of table distance from column.
Note: Table or table support parts are not
interchangeable between the W1669 and the
W1670 drill presses (see Figures.27.and.28).
To.adjust.the.table,.do.these.steps:
1... Loosen the table lock lever.
2. Turn the hand crank to raise or lower the
table.
3. Tighten the table lock lever.
4. For the W1670, loosen the table tilt lock
bolt (see Figure.29); or for the W1669,
loosen the cap screw.
5. Turn the index pin draw nut clockwise and
draw the index pin out of the casting until
you can rotate the table to your desired
angle (see Figure.29).
Note: Use this index pin only for indexing
the table to the “Zero degree” position.
Note: To index the table back to the zero
position, back off the draw nut, turn the
table to zero, tap the index pin back into
the casting, and tighten the table tilt lock
bolt.
6. Tighten the tilt table lock bolt or cap
screw, and double check your angle.
Figure.27..W1669 Table support assembly.
Figure.28..W1670 Table support assembly.
Figure.29..Tilt mechanism and lock bolt.
Table-Tilt
Lock Bolt
(W1670)
or
Table-Tilt
Lock Cap
Screw
(W1669)
Index Pin
and
Draw Nut
Tilt
Scale
ADJUSTMENTS
-18-
This drill press will perform many types of oper-
ations that are beyond the scope of this manual.
Many of these operations can be dangerous or
deadly if performed incorrectly.
The instructions in this section are written with
the understanding that the operator has the
necessary knowledge and skills to operate this
machine. If at any time you are experiencing
difficulties performing any operation, stop using
the machine!
If you are an inexperienced operator, we
strongly recommend that you read books, trade
articles, or seek training from an experienced
lathe operator before performing any unfamiliar
operations. Above all, your safety should come
first!
To.start.the.drill.press,.do.these.steps:
1. Make sure the starting switch paddle is
down for OFF.
2. Make sure all fasteners and lock handles are
tight.
3. Make sure the drill chuck key is removed.
4. Plug in the power cord.
5. Lift the ON/OFF switch to start the drill
press, and make sure that your fingers are
poised near the paddle, as shown in Figure.
30..In case there is a problem you can turn
the drill press off.
6. Observe and listen to the drill press, it
should run smoothly, with little or no vibra-
tion or rubbing noises.
• If you hear strange or unusual noises, shut
the drill press OFF, and wait for the spin-
dle to stop moving.
7. Unplug the drill press and refer to the
“Troubleshooting” table on Page.27
to help isolate and correct the problem
before using the drill press again.
Figure.30..Fingers poised near the stop switch.
WEAR.safety.goggles.and.
a.respirator.during.drill-
ing. or. sanding. opera-
tions.. Otherwise. seri-
ous.personal.injury.may.
occur!
Keep. your. shop. “Child.
Safe.”. Always. remove.
the. switch. safety. key.
when.drill.press.is.not.in.
use.. Serious. injury. may.
occur.
Test.Run
OPERATIONS
OPERATIONS
To drill wide workpieces up to 34" in diam-
eter, you can slide the headstock in and out
to increase the distance between the drill
chuck and the column up to 17". You can also
tilt the headstock from 45° clockwise to 90°
counterclockwise for drilling angled holes or for
horizontal boring machine use. Using the slide
and tilt features, you can drill a line of straight
or angled holes without the need to reposition
your workpiece after drilling each hole.
To.use.the.headstock-sliding.feature,.do.
these.steps:
1. Loosen the lock lever located on the right
side of headstock (see Figure.31).
2..
Turn the slide knob to move the headstock
back and forth to desired position and then
tighten the lock lever (see Figure.31).
.
To.use.the.headstock-tilting.feature,.do.
these.steps:
Note: If the scale is not calibrated, set the
table to zero degrees, zero the headstock with
the table, and then reposition the scale to zero
degrees.
1.. Loosen the lock handle on the right side of
headstock (see Figure.31).
2.. Pull out the guide pin knob located on the
left side of the headstock and rotate the
pin knob 90° so the pin stays disengaged
from the horizontal column (see Figure.
32).
3.. While reading the tilt scale, tilt the head-
stock to your desired angle and tighten
lock lever (see Figure.31).
4.. Drill your workpiece.
5.. Loosen lock handle located on the right
side of headstock, and tilt the headstock
to zero and move the guide pin back into
the guide slot.
6.. Tighten the lock lever.
Headstock
Figure.31. Headstock tilt and slide controls.
Figure.32..Headstock guide pin and knob.
Lock
Lever
Slide
Knob
Guide Pin
and Knob
Horizontal Column
OPERATIONS
-20-
To.change.a.drill.bit.or.sanding.drum,.do.
these.steps:
1. UNPLUG.THE.DRILL.PRESS!
2.. Use the chuck key to remove the old drill
bit, and open the chuck wide enough to
accept the new bit or the sanding drum
mandrel (see Figure.33).
3.. Install the bit or mandrel so the chuck jaws
will grab as much of the bit or mandrel
shank as it can.
• If you are installing a small drill bit, make
sure it is held between three jaws instead
of only two, and NEVER allow a chuck to
grab the fluted body of drill bits.
4.. Using any of the three key locations,
tighten the chuck with the chuck key and
remove.the.key (see Figure.34).
Figure.34..Using the chuck key.
Figure.33..Installing a drill bit.
TURN. OFF. and. UNPLUG.
the. drill. press,. and. wait.
until. all. working. parts.
are. stopped. before. you.
attempt. to. change. drill.
bits.. Otherwise,. severe.
injury.may.occur!
Changing.Drill.Bits
The chuck supplied with your W1669 or W1670
drill press accepts drill bits from 1/32" to 5⁄8''.
Follow the steps below to safely swap drill bits
or sanding spindles.
OPERATIONS
Speed.Changes
To.change.the.drilling.speed,.do.these.steps:
1... UNPLUG.THE.DRILL.PRESS!
2.. Loosen the belt tension lock knobs on the
side of the headstock (see Figure.35).
3. Locate the desired speed on the chart and
move the V-belt to the desired V-grooves
on the motor and spindle pulleys (see
Figure.36).
4.. Push the motor inward, and move the V-
belt to the right spot.
5.. Push the motor toward the back of the
headstock. The motor support rod is spring
loaded and will follow the motor. Tighten
the lock knob when the right tension is
achieved.
6. Close the cover.
UNPLUG. the. drill. press.
before. changing. speeds.
to.avoid. accidental.start.
up..Failure.to.do.this.may.
result.in.serious.personal.
injury.
The Model W1669 and W1670 Radial Drill Press
has 5 speeds ranging from 550 to 3470 RPM.
To find your needed drilling speed and pulley
combination, refer to the speed chart located
under the belt guard; or go to.Page.22 and
refer to the Drill.Press.RPM.Chart.
Figure.35..Loosening lock knob.
Figure.36..Adjusting belt to desired speed.
Never.operate.drill.press.
with. belt. cover. in. the.
open.position..Your.hand.
may.become.trapped.in.a.
belt.and.serious.personal.
injury.will.occur.
Pushrod
OPERATIONS
-21-
Use Figure.37.to select the optimum motor-to-spindle pulley ratio for drilling, cutting, and sanding
operations. for example the above figure shows the belt in the C position on the spindle pulley and the
#3 position on the motor pulley, which will give a speed of 1,520 RPM. Refer to the Drill,. Cutter,.and.
Saw.RPM.Chart on Page.23 for suggested tool RPMs.
Figure.37..Drill Press RPM Chart.
Drill.Press.RPM.Chart
Drilling.Depth
Your new drill press comes fitted with a depth
stop that allows drilling many holes at a pre-
set depth consistently. When the hex nuts are
set, the nuts will contact the stop flange and
stop the drill press from drilling any deeper.
To.adjust.the.drilling.depth,.do.these.steps:
1. Measure the maximum depth that you want
to drill a series of holes at. In this example
the maximum depth is 1
1
⁄4" deep.
2. Loosen the hex nuts shown on the depth
stop and align the lower nut to the 1
1
⁄4"
mark on the depth stop rod (see Figure.
38).
3. Hold the lower hex nut and tighten the
upper hex nut so both nuts are locked
together.
4. Make sure the depth has been set cor-
rectly, measure, or drill a hole into scrap
wood before drilling into any workpiece.
Figure.38..Depth stop set for 1
1
⁄4" drilling
depth.
Depth..
Stop
Upper
Hex Nut
Stop.
Flange
Lower.
Hex.Nut
1-1⁄4"
OPERATIONS
-22-
Drill,.Cutter,.and.Hole.Saw.Suggested.RPM.Chart
-23-
..
..
..
..
..
..
..
..
..
..
..
..
..
..
.
OPERATIONS
-24-
OPERATIONS
-25-
Since all bearings are shielded and permanently
lubricated, simply leave them alone until they
need to be replaced. DO.NOT lubricate them.
For other items on this machine, such as the
quill, table and column, horizontal and verti-
cal columns, an occasional application of light
machine oil is all that is necessary to maintain
smooth rust-free operation.
Before applying any lubricant, clean off the old
lubricant, and any sawdust or metal chips.
DO.NOT over lubricate, your goal is to achieve
adequate lubrication. Too much lubrication will
attract dirt and sawdust, and various parts of
your machine could loose freedom of move-
ment.
Periodic maintenance on your Model W1669 and
W1670 Radial Drill Press will ensure its opti-
mum performance. Make a habit of inspecting
your drill press after each use.
Check.for.the.following.conditions.and.repair.
or.replace.when.necessary.
1. Loose or missing base mounting bolts.
2. Worn switch.
3. Worn or damaged cords and plugs.
4. Damaged drive belt.
5. Any other condition that could hamper the
safe operation of this machine.
Keep the table and other unpainted surfaces
rust-free with regular applications of prod-
ucts like Boeshield® T-9. For long term stor-
age consider products like Kleen Bore's Rust
Guardit™.
NEVER. adjust. or. service.
the. machine. while. it. is.
running.. Wait. until. the.
machine. is. turned. off,.
unplugged.and.all.working.
parts.have.come.to.a.stop.
before.proceeding!
Table.and.Base
Lubrication
General
MAINTENANCE
MAINTENANCE
-26-
Troubleshooting
MAINTENANCE
This section covers the most common symptoms and corrections with this type of machine.
WA RNING!.DO.NOT.make.any.adjustments.until.power.is.disconnected.and.moving.parts.
have.come.to.a.complete.stop!
-27-
W1669.and.W1670.Drill.Press.110V.Wiring
ELECTROCUTION HAZARD!
Disconnect all power to the machine
and wall receptacle before doing any
electrical service. Otherwise, you
or others may be burned or
electrocuted resulting in injury or
death!
Start
Capacitor
Capacitor
Cover
110V
Motor
Start
Switch
Blk
Wht
Wht
Blk
Wht
Wht
Wht
Blk
Blk
Grn
Grn
Grn
5-15 Plug
Red
Red
Wht
MAINTENANCE
43
47
39
37
51
50
44
48
29
45
59
75
60
32
31
46
27
34
36
28
28A
28
42
41
40
33
20
64
65
66
54
38
53
22
23
93
36
19
56
49
76
53
21
26
62
25
35
52
63
10
77
81
9
30
8
85
86
24
88
87
76
0
1
2
3
15
94
103
79
381
89
351
194
191
192
193
45A3
45A1
45A2
16A1
16A
11
196
195
321
102
107
105
104
107
106
108
89
331
-28-
W1669.and.W1670.
Parts
MAINTENANCE
MAINTENANCE
-29-
PARTS
.REF. PART.#. .DESCRIPTION
8 X1669008 GEAR
9 XPR16M EXT RETAINING RING 9MM
10 XPN03M HEX NUT M8-1.25
11 X1668019 CLAMP BOLT M10-1.5 X 30
15 X1669015 KNOB BOLT M8-1.25 X 16
16A X1669016A MOUNT PLATE N/S
16A-1 X1669016A-1 MOTOR PLATE N/S
19 X1669019 MOTOR
1
⁄2 HP, 110V
19-1 X1669019-1 S. CAPCTR 150MFD/125VAC
19-2 X1669019-2 CAPACITOR COVER
19-3 X1669019-3 MOTOR FAN
19-4 X1669019-4 FAN COVER
19-5 XPS54M PHLP HD SCR M4-.75 X 6
19-6 XPW05M FLAT WASHER 4MM
20 X1669020 PULLEY COVER
21 X1669021 MOTOR PULLEY
22 X1669022 V-BELT 0-1480
23 X1669023 UNTHREADED FEMALE KNOB
24 X1669024 LOCK PIN ASSEMBLY
25 X1669025 SPINDLE PULLEY
26 X1669026 DRIVE SLEEVE
27 XPR23M INT RETAINING RING M40
28 XP6203 BEARING 6203
28A X1669028A SPACER
29 X1669029 KNOB
30 X1669030 LEVER
31 XPLN08 LOCK NUT
1
⁄2"-20
32 X1669032 COVER WITH SPRING
32-1 X1669032 COVER WITH SPRING
33 X1669033 HORIZONTAL COLUMN
33-1 X1669033-1 HORIZONTAL COLUMN RACK
34 X1669034 HEADSTOCK
35 XPSW09 SWITCH AND KEY
35-1 XPSW09-1 SWITCH KEY
36 XPSS02 SET SCREW
5
⁄16"-18 X
3
⁄8"
37 XPS22 PHLP SCREW 10-24 X
5
⁄8"
38 X1669038 SWITCH BOX
38-1 X1669038-1 SWITCH MOUNTING PLATE
39 X1669039 RUBBER WASHER
40 X1669040 QUILL SHAFT
41 XP6202 BEARING 6202
42 X1669042 SPINDLE JT#33
.REF. PART.#. .DESCRIPTION
43 X1669043 CHUCK KEY
44 X1669044
1
⁄2" CHUCK 1-16MM JT#33
45 X1668031 COLLAR
45A-1 X1668031A DEPTH STOP ROD N/S
45A-2 X1669045A-1 DEPTH STOP ROD BRACKET
45A-3 X1668031A-6 DEPTH STOP MOUNT
46 X1668030 FEED SHAFT
47 X1668033 FEED COLLAR
48 X1669048 HANDLE
49 X1669049 DEGREE SCALE
50 XPR03M EXT RETAINING RING 12M
51 XP6201 BEARING 6201
52 X1669052 POWER CORD
53 X1669053 SET SCREW
54 XPS07 PHLP SCREW
1
⁄4"-20 X
3
⁄8"
56 X1669056 RIVET
59 X1669059 SPECL SET SCR
5
⁄16"-18 X 1"
60 XPN02 HEX NUT
5
⁄16"-18
62 X1669062 LABEL
63 X1669063 WIRE STRAP
64 XPS06 PHLP SCREW 10-24 X
3
⁄8"
65 X1669065 MOTOR SWITCH CORD
66 X1669066 SPEED CHART
75 X1669075 SAFETY LABEL
76 X1669076 LOCKING GIB
77 XPW01M FLAT WASHER 8MM
79 XPW06M FLAT WASHER 12MM
81 XPB09M HEX BOLT M8-1.25 X 20
85 X1669085 SAFETY GOGGLES LABEL
86 X1669086 LONG HAIR SAFETY LABEL
87 XPAW03M HEX WRENCH 3MM
88 XPAW05M HEX WRENCH 5MM
89 XPHTEK7 SELF TAP SCREW #8 X
3
⁄8"
93 X1669093 RUBBER WASHER 8MM
94 X1669094 GUIDE ROD 16 X 30MM
102 XPN02M HEX NUT M10-1.5
103 XPLW06M LOCK WASHER 10MM
104 XPW03M FLAT WASHER 6MM
105 XPS68M PHLP HD SCR M6-1 X 10
106 XPN03M HEX NUT M8-1.25
107 XPN02M HEX NUT M10-1.5
108 XPSB14M CAP SCREW M8-1.25 X 20
W1669,.W1670.Parts.List
-30-
1
3
4
5
83
84
78
79
71
73
74
7
7
8
73
7
98
93
13
91
99
7
841
5
11
11
71
W1669.Parts
MAINTENANCE
MAINTENANCE
-31-
PARTS
.REF. PART.#. .DESCRIPTION
1 X1669001 BASE
3 XPB09M HEX BOLT M8-1.25 X 20
4 X1669004 W1669 RACK
5 X1669005 W1669 COLUMN
7 X1669007 GEARED TBL BRKT N/S
7-1 X1669007-1 COMPLETE TBL BRKT ASSY
7-2 X1669007-2 GEARED TBL BRKT SCALE
11 X1668019 LEVER BOLT M10-1.5 X 30
13 X1669013 HORR. COLUMN BRKT
54 XPS07 PHLP SCREW
1
⁄4"-20 X
3
⁄8"
56 X1669056 RIVET
70 X1669070 PIN
71 X1669071 WORM PINION
.REF. PART.#. .DESCRIPTION
72 X1669072 LIFT HANDLE CRANK
73 XPSS01M SET SCREW M6-1.0 X 10
74 X1669074 10T GEAR
78 XPSB77M CAP SCREW M12-1.75 X 30
79 XPW06M FLAT WASHER 12MM
80 X1669080 COLUMN RING
83 X1669083 TABLE
84 X1669084 COLUMN SUPPORT ARM N/S
84-1 X1669084-1 SCALE
91 XPAW10M HEX WRENCH 10MM
93 X1670093 HEX BOLT M8-1.25 X 125
99 XPLW05M LOCK WASHER 12MM
98 XPWN02M WING NUT M8-1.25
W1669.Parts.List
-32-
1
71
73
74
70
72
4A
84
94
95
96
97
11
11
84A
80
73
7
3
98
93
13
83
5A
101
92
56
72
841
71
W1670.Parts
MAINTENANCE
MAINTENANCE
-33-
PARTS
.REF. PART.#. .DESCRIPTION
1 X1670001 BASE
3 XPB31M HEX BOLT M10-1.5 X 40
4A X1670004A W1670 RACK
5A X1670005A W1670 COLUMN
7 X1668010A GEARED TBL BRKT N/S
7-1 X1668010A-2 COMPLETE TBL BRKT ASSY
7-2 X1669007-2 SCALE
11 X1668019 LEVER BOLT M10-1.5 X 30
13 X1670013 HORR. COLUMN BRKT
56 X1669056 RIVET
70 X1668010A-3 AXLE
71 X1668012 WORM PINION
72 X1668016 LIFT HANDLE
73 XPSS01M SET SCREW M6-1.0 X 10
.REF. PART.#. .DESCRIPTION
74 X1668015 WORM GEAR
80 X1668008 COLUMN RING
83 X1670083 TABLE
84 X1668010A-1 COLUMN SUPPORT ARM N/S
84-1 X1669084-1 SCALE
84A X1670084A TABLE SUPPORT ARM
92 X1668013 CLAMP BOLT M12-1.75 x 50
93 X1670093 HEX BOLT M8-1.25 X 125
94 XPN01M HEX NUT M6-1.0
95 X1668111B SPECIAL PIN
96 X1670096 HEX BOLT
5
⁄8"-13 X 1
1
⁄2"
97 XPW14 FLAT WASHER
5
⁄8"
98 XPWN02M WING NUT M8-1.25
101 X1668152 SPECIAL WRENCH
W1670.Parts.List
SHOP FOX
®
.Drill. Press. Vises use precision ground steel guide rods,
smooth-action Acme threads, ground steel jaws, with fixed jaw V-grooves
for holding round stock, and dovetailed ways where applicable.
D2727
SHOP FOX
®
(3" Basic Vise)
D2728
SHOP FOX
®
(4" Basic Vise)
D2729
SHOP FOX
®
(6" Basic Vise)
D2933
SHOP FOX
®
(3
3
⁄4" Angle Vise)
D2730
SHOP FOX
®
(3" Cross Sliding Vise)
D2731
SHOP FOX
®
(4" Cross Sliding Vise)
The 4".PRO-STIK
®
Stick with Handle
is the easiest solution for
increasing
the life of sanding sleeves by removing pitch and sawdust particles
from
the abrasive pores, which later harden in place if not removed.
Simply
press the cleaner lightly against the moving abrasive surface to remove
clogged-up pitch and sawdust.
PRO-STIK
®
cleaners are available in other
sizes for any cleaning application that would need cleaners with handles,
as blocks, or as flat pads. (Not recommended for wide-belt sanders.)
-34-
The following drill press accessories may be available through your local Woodstock International Inc.
Dealer. If you do not have a dealer in your area, these products are also available through online dealers.
Please call or e-mail Woodstock International Inc. Customer Service to get a current listing of dealers at:
1-800 840-8420 or at [email protected].
D2677. Drum. Sander. Set includes three rubber sanding drums 4
1
⁄
4
" in
length to accommodate 1", 1
1
⁄
2
" and 2" diameter sanding sleeves. This kit
also includes one 80 grit sleeve for each drum to get things started.
D2722.Mandrel is a
3
⁄
8
" shank and is required to use with the Drum Sander
Set with any drill press.
Drill. Press. Clamps
adjust quickly and easily to lock your workpiece
in any position. The clamping pad pivots to conform to any workpiece,
ensuring uniform pressure.
W1301 6" Drill Press Clamp (1
1
⁄2" Capacity)
D2192 10" Drill Press Clamp (3" Capacity)
D2493 12" Drill Press Clamp (5" Capacity)
Accessories
Sanding.Sleeves are sized to fit the D2677 Drum Sander Set. These hard
Sanding Sleeves are available in 60, 80, 100, 120, and 150 grits. Keep
plenty of these consumable Sanding Sleeves on hand.
Sanding.Sleeves
. Size
.
. (Dia..x.Ht.).
60.Grit. 80.Grit
.
. 100.Grit. 120.Grit. 150.Grit
. 1".X.4
1
⁄
4
". D2683. D2684. D2685. D2686. D2687
.1
1
⁄
2
".X.4
1
⁄
4
". D2688. D2689. D2690. D2691. D2692
. 2".X.4
1
⁄
4
". D2693. D2694. D2695. D2696. D2697
MAINTENANCE
MAINTENANCE
-35-
Steelex
®
.Carded.Forstner.Bits
stack up as some of the best bits in
the world. In fact, an independent testing lab proved that the
Steelex
®
brand cut was equal to or better than Forstner Bits from
Austria, known for being the best. For use with drill presses.
Refer
to http://www.woodstockint.com/forstner.cfm for a complete
product line available through your dealer.
Woodstock. offers. a. full. line. of. Brad. Point. Bits,Tenon/Plug.
Cutters,. Countersink. Bits,. and. Stubby. Drill. Bits to satisfy
every need. Whether for do-it-yourselfers or professional
woodworkers, you can depend on Woodstock International
Inc. to manufacture a useful selection of drilling and cutting
tools. Refer to http://www.woodstockint.com/drilling.cfm
for a complete product line available through your dealer.
D2251.Steelex
®
..Adjustable.Circle.Cutter
cuts flat-sided holes in wood
from 1" to 5". Made of M-2 alloy steel, this Circle Cutter features a
3
⁄8" hex
shank,
5
⁄16" drill, center point and hex wrench.
D3161.Steelex
®
..Heavy-Duty.Carbide-Tipped.Adjustable.Circle.Cutter.
is Carbide Tipped and cuts 1
3
⁄4" to 5
3
⁄4" diameter holes in the toughest
material. For use with
1
⁄2" drill press chucks. Includes hex wrench and
7
⁄16"
pilot drill.
The.SHOP FOX
®
D2056.Tool.Table
is great for bench-top tools like chop
saws, drill presses, planers, scroll
saws and bandsaws. Support cross braces
on top provide incredible
strength and capacity. Flared legs and adjustable
rubber feet ensure stability and reduce machine vibration. Butcher block
finish table top measures 13" x 23" and is 30
1
⁄2" tall with a 700 lb. capacity.
Steelex.Plus
®
.
Bi-Metal.Hole.Saws stay sharper longer than carbon steel
hole saws. Equipped with high-speed steel alloy cutting teeth bonded to
a welded steel body, they cut wood, metal and plastics with ease.
D2784 10-pc. Bimetal Hole Saw Set
D2020 8-pc. Aggressive Hole Saw Set
D2783 6-pc. Bimetal Hole Saw Set
D2797
1
⁄2" X 20 UNF Hole Saw Arbor
D2798
5
⁄8" X 18 UNF Hole Saw Arbor
D2799
12" Hole-Saw Arbor Extension
D2928
Replacement Pilot Drill for D2797
D2929
Replacement Pilot Drill for D2798
-36-
Notes
Notes
-37-
Woodstock International, Inc. warrants all SHOP FOX
®
machinery to be free of defects from workman-
ship and materials for a period of two years from the date of original purchase by the original owner.
This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence or acci-
dents, lack of maintenance, or reimbursement of third party expenses incurred.
Woodstock International, Inc. will repair or replace, at its expense and at its option, the
SHOP FOX
®
machine or machine part which in normal use has proven to be defective, provided that the original
owner returns the product prepaid to the
SHOP FOX
®
factory service center or authorized repair facil-
ity designated by our Bellingham, WA office, with proof of their purchase of the product within two
years, and provides Woodstock International, Inc. reasonable opportunity to verify the alleged defect
through inspection. If it is determined there is no defect, or that the defect resulted from causes not
within the scope of Woodstock International Inc.'s warranty, then the original owner must bear the cost
of storing and returning the product.
This is Woodstock International, Inc.'s sole written warranty and any and all warranties that may be
implied by law, including any merchantability or fitness, for any particular purpose, are hereby lim-
ited to the duration of this written warranty. We do not warrant that
SHOP FOX
®
machinery complies
with the provisions of any law or acts. In no event shall Woodstock International, Inc.'s liability under
this warranty exceed the purchase price paid for the product, and any legal actions brought against
Woodstock International, Inc. shall be tried in the State of Washington, County of Whatcom. We shall
in no event be liable for death, injuries to persons or property or for incidental, contingent, special or
consequential damages arising from the use of our products.
Every effort has been made to ensure that all
SHOP FOX
®
machinery meets high quality and durabil-
ity standards. We reserve the right to change specifications at any time because of our commitment to
continuously improve the quality of our products.
Warranty
Name ___________________________________________________________________________________
Street __________________________________________________________________________________
City _________________________ State ___________________________Zip ________________________
Phone # ______________________ E-mail __________________________Invoice # ___________________
Model #_________Serial #______________Dealer Name__________________Purchase Date___________
Wa rranty.Registration
The following information is given on a voluntary basis. It will be used for marketing purposes to help us
develop better products and services. Of course, all information is strictly confidential.
1. How did you learn about us?
_____ Advertisement _____ Friend ____ Local Store
_____ Mail Order Catalog _____ Website ____ Other:
2. How long have you been a woodworker/metalworker?
_____ 0-2 Years _____ 2-8 Years ____ 8-20 Years _____ 20+ Years
3. How many of your machines or tools are Shop Fox
®
?
_____ 0-2 _____ 3-5 ____ 6-9 _____ 10+
4. Do you think your machine represents a good value? _____ Yes ____ No
5. Would you recommend Shop Fox
®
products to a friend? _____ Yes ____ No
6. What is your age group?
_____ 20-29 _____ 30-39 ____ 40-49
_____ 50-59 _____ 60-69 ____ 70+
7. What is your annual household income?
_____ $20,000-$29,000 _____ $30,000-$39,000 ____ $40,000-$49,000
_____ $50,000-$59,000 _____ $60,000-$69,000 ____ $70,000+
8. Which of the following magazines do you subscribe to?
9. Comments:.__________________________________________________________________
. _____________________________________________________________________________.
. _____________________________________________________________________________.
. _____________________________________________________________________________.
____ Cabinet Maker
____ Family Handyman
____ Hand Loader
____ Handy
____ Home Shop Machinist
____ Journal of Light Cont.
____ Live Steam
____ Model Airplane News
____ Modeltec
____ Old House Journal
____ Popular Mechanics
____ Popular Science
____ Popular Woodworking
____ Practical Homeowner
____ Precision Shooter
____ Projects in Metal
____ RC Modeler
____ Rie
____ Shop Notes
____ Shotgun News
____ Today’s Homeowner
____ Wood
____ Wooden Boat
____ Woodshop News
____ Woodsmith
____ Woodwork
____ Woodworker West
____ Woodworker’s Journal
____ Other:
TAPE ALONG EDGES--PLEASE DO NOT STAPLE
FOLD ALONG DOTTED LINE
FOLD ALONG DOTTED LINE
WOODSTOCK.INTERNATIONAL,.INC.
P.O..BOX.2309
BELLINGHAM,.WA..98227-2309
Place
Stamp
Here
