���*��mm ���g铜版纸，折页双面印刷
Overall Product Schematic Diagram Quick Sta Guide
Magnetic Wireless Charging
Area for Mobile Phones
Wireless Charging Area for Watches
Wireless Charging Area for Headphone Charging Cases
Aluminum Alloy Suppo Rod
Type-C Po
Indicator Light
Product Specications
Product Name:
3-in-1 Magnetic Wireless Charging Station
Product Dimensions:
��mm*��mm*��mm
USB-C Input:
��V⎓�.�A ��V⎓�.�A
Operating Frequency:
���-���KHz
Conversion Eciency:
��%-��%
Mobile Phone Output:
25W(max)
Watch Output:
2.5W(max)
Headphone Outpu:
5W(max)
Eective Wireless Charging
Distance (for Mobile Phone):
≤�mm
Material:
ABS+Silicone + Aluminum Alloy
3-in-1 Magnetic
Wireless Charging Station
Indicator Light
❶ Product Front ❷ Product Back
❸Angle Adjustable 65°
��°
❹Concealed Sliding Watch Charger
Instruction Manual
Operating Instructions
❶is product can wirelessly charge three devices simultaneously: mobile phones,
watches, and wireless headphone charging cases that suppo wireless charging.
❷Please connect this wireless charger to a power adapter using a Type-C fast
charging cable and turn on the power.
❸Place your mobile phone on the mobile phone charging area, and it will sta
charging automatically.
❹Place your watch on the watch charging area, and it will sta charging
automatically.
❺Place your wireless headphone charging case on the headphone charging area,
and the charging case will sta charging automatically.
Adapter Selection
Please use a PD protocol adapter with a power
output of 45W or higher. e maximum
charging power for mobile phones is 25W.
Indicator Light Status
Indicator LightMode
White light turns on, then switches to green light, then
back to white light, and turns o after 3 seconds
Power-on
Light oStandby
Green light turns on and turns o after 5 seconds
Light o
White light ashes continuously until the abnormal
state is resolved
Headphone Charging
Case Charging
Fully Charged
Mobile Side FOD
Protection
Green light ashes continuously until the abnormal
state is resolved
Headphone Side FOD
Protection
Package List
Wireless Charger × 1 Charging Cable × 1 User Manual × 1
Warning!
Precautions
Applicable Devices
Please check if your mobile phone suppos wireless charging.
is product suppos fast wireless charging, which realizes sho-distance wireless
power transmission through coil induction.
Donot place metal debris or magnetic cards on the charging pad, as this may
cause the charger to heat up!
When a foreign object alarm is triggered, remove the foreign object immediately!
Slight heating is a normal phenomenon; the mobile phone batte will generate
heat during charging!
Do not place the charger near re sources or in corrosive environments!
FCC Warning Statement
Changes or modications not expressly approved by the pay responsible for
compliance could void the user’s authority to operate the equipment. is
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Pa 15 of the FCC Rules. ese limits are designed to
provide reasonable protection against harmful inteerence in a residential
installation. is equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful inteerence to radio communications. However, there is no
guarantee that inteerence will not occur in a paicular installation. If this
equipment does cause harmful inteerence to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to
t to correct the inteerence by one or more of the following measures:
‐‐ Reorient or relocate the receiving antenna.
‐‐ Increase the separation between the equipment and receiver.
‐‐ Connect the equipment into an outlet on a circuit dierent from that to which
the receiver is connected.
‐‐ Consult the dealer or an experienced radio/TV technician for help.
FCC Radiation Exposure Statement
e antennas used for this transmitter must be installed to provide a separation
distance of at least 20 cm from all persons and must not be co‐located for
operating in conjunction with any other antenna or transmitter.
is device complies with Pa 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)is device may not cause harmful inteerence.
(2)is device must accept any inteerence received, including inteerence that
may cause undesired operation.
